parking brake VOLVO XC60 2010 Owner´s Manual

06 Maintenance and specifications
Replacing bulbs
06
234* Option/accessory, for more information, see Introduction.
Introduction
All bulb specifications are listed on page 240.
The following bulbs should only be replaced by
a trained and qualified Volvo service techni-
cian:
•Dome lighting
•Reading lights
•Glove compartment lighting
•Turn signals in the door mirror
•Approach lighting in the door mirror
•Brake/fog/taillights
•Rear side parking lights
•Active Bending Lights and LED bulbs
NOTE
For information regarding any other bulbs
not mentioned in this section, please con-
tact your Volvo retailer or a trained and
authorized Volvo service technician.
WARNING
•Active Bending Lights* – due to the high
voltage used by these headlights, these
bulbs should only be replaced by a
trained and qualified Volvo service tech-
nician.
•Turn off the lights and remove the
remote key from the ignition before
changing any bulbs.
Headlight housing
G010325
WARNING
•The engine should not be running when
changing bulbs.
•When changing in the headlight hous-
ing, if the engine has been running just
prior to replacing bulbs, please be
aware that components in the engine
compartment will be hot.
The entire headlight housing must be lifted out
when replacing all front bulbs (except for the
fog lights).
CAUTION
Never touch the glass of bulbs with your fin-
gers. Grease and oils from your fingers
vaporize in the heat and will leave a deposit
on the reflector, which will damage it.

06 Maintenance and specifications
Replacing bulbs
06
238
2. Remove the bulb holder by turning it coun-
terclockwise and pulling it out of the head-
light housing.
3. Pull out the burned out bulb and install a
new one. It can only be inserted in one
position.
4. Reinsert the bulb holder into the headlight
housing and turn it clockwise.
5. Reinstall the headlight housing.
Front fog lights
Remove the fog light lens by pulling out the
upper corner that is closest to the grille.
1. Pull the lens straight out toward the center
of the car using a tool as shown in the illus-
tration.2. Unscrew the fog light housing screw and
pull out the fog light.
3. Turn the bulb counterclockwise and pull it
out.
4. Insert a new bulb and turn it clockwise.
5.
Reinstall the bulb holder. The TOP mark on
the bulb holder must always be upward.
6. Tighten the fog light housing screw and
reinstall the lens.
Rear fog light
The rear fog light (located on the driver's side
of the vehicle) can be reached from behind the
bumper
1. Remove the bulb holder by turning it coun-
terclockwise.2. Remove the burned out bulb by pressing it
in and turning it counterclockwise.
3. Insert a new bulb, press it in and turn it
clockwise.
4. Reinsert the bulb holder and turn it clock-
wise.
Location of taillight bulbs
Taillight lens, right side
Parking/side marker lights (LED)
Side reflector
Brake light
Backup light
Turn signal
Brake lights (LED)

06 Maintenance and specifications
Fuses
06

* Option/accessory, for more information, see Introduction.251 Under the glove compartment
Fold aside the iupholstery covering the fuse
box.
1. Press the cover's lock and fold it up.
2. The fuses are accessible.
Positions
FunctionA
Rain sensor*5
SRS system10
ABS brakes. Electric parking
brake5
FunctionA
Accelerator pedal, heated
seats*7.5
–
ICM display, CD & Radio15
Steering wheel module7.5
–
High beam15
FunctionA
Laminated panoramic roof*20
Backup lights7.5
–
Front fog light*15
Windshield washers15
Adaptive cruise control ACC*10
–

06 Maintenance and specifications
Fuses
06
254* Option/accessory, for more information, see Introduction.
Module (white). Func-
tionA
Park assist, Park assist cam-
era*5
Control module Four C*15
Heated driver's seat*15
Heated passenger's seat*15
Rear seat heater, passenger's
side*15
AWD control module10
Rear seat heater, driver's
side*15
–
Power passenger's seat*25
Keyless drive*20
Electric parking brake – driv-
er's side*30
-
Module (blue). Func-
tionA
Navigation system display*10
–
Subwoofer*25
SIRIUS satellite radio*5
Audio amplifier*25
Audio system15
Bluetooth Hands-free system5
Reserve –

06 Maintenance and specifications
Wheels and tires
06
266
Changing a wheel
Location of jack and tools
Spare wheelThe spare wheel (Temporary spare) is only
intended for temporary use. Replace the spare
wheel with a normal wheel as soon as possible.
The car's handling may be altered by the use
of the spare wheel. The correct tire pressure for
the spare wheel is stated in the tire pressure
tables on pages 260 and 260.
WARNING
Current legislation prohibits the use of the
“Temporary Spare” tire other than as a tem-
porary replacement for a punctured tire. It
must be replaced as soon as possible by a
standard tire. Road holding and handling
may be affected with the “Temporary
Spare” in use.
CAUTION
The vehicle must never be driven with more
than one temporary spare wheel.
The spare wheel is located in the spare wheel
well with the rim side down. There are two foam
blocks, one under the spare wheel and one
over/inside. The upper one contains all tools.
The same bolt runs through to secure the spare
wheel and the foam blocks.
Taking out the spare wheel1. Fold the rear edge of the floor mat forward.
2. Open the floor hatch.
3. Undo the retaining bolt.
4. Lift out the foam block with tools.
5. Lift out the spare wheel.
The other two blocks can remain in the wheel
well.
After useThe foam block and spare wheel must be
replaced in the reverse order. Note the arrow
on the upper foam block. It should point for-
ward.
Removing the wheel cover
Changing a tire:1. Apply the parking brake.
2.
Put the gear selector in P.
3. Block the wheels that are on the ground
with wooden blocks or large stones.
4. Remove the wheel cover (where applica-
ble) using the lug wrench in the tool
bag.With the vehicle still on the ground,
use the lug wrench to loosen the wheel

06 Maintenance and specifications
Wheels and tires
06

267
nuts 1/2 – 1 turns by exerting downward
pressure.
5. Turn the nuts counterclockwise to loosen.
6. There are two jack attachment points on
each side of the vehicle. Position the jack
correctly in the attachment (see illustration
above) and crank while simultaneously
guiding the base of the jack to the ground.
The base of the jack must be flat on a level,
firm, non-slippery surface. Before raising
the vehicle, check that the jack is still cor-
rectly positioned in the attachment.
7. Raise the vehicle until the wheel to be
changed is lifted off the ground.
WARNING
There are two attachment points near the
rear of the vehicle. Only the rear-most
attachment point is intended for the jack
(see the illustration).
8. Raise the vehicle until the wheel to be
changed is lifted off the ground.
9. Unscrew the wheel nuts completely and
carefully remove the wheel so as not to
damage the threads on the studs.
WARNING
•The jack must correctly engage the jack
attachment.
•Be sure the jack is on a firm, level, non-
slippery surface.
•Never allow any part of your body to be
extended under a vehicle supported by
a jack.
•Use the jack intended for the vehicle
when changing a tire. For any other job,
use stands to support the vehicle.
•Apply the parking brake and put the
gear selector in the Park (P) position.
•Block the wheels standing on the
ground, use rigid wooden blocks or
large stones.
•The jack should be kept well-greased
and clean, and should not be damaged.
•No objects should be placed between
the base of jack and the ground, or
between the jack and the attachment
bar on the vehicle.
Re-installing the wheel1. Clean the contact surfaces on the wheel
and hub.
2. Lift the wheel and place it on the hub.

06 Maintenance and specifications
Wheels and tires
06
270
upper and lower eyelids. Get medical
attention if symptoms occur.
•Inhalation: Move the person to fresh air.
If irritation persists, get medical atten-
tion.
Tire sealing system–temporarily
repairing a flat tire
G014338
Temporarily repairing a flat tire is done in two
stages:
•Stage 1: The hole is sealed by pumping
sealing compound into the tire. The car is
then driven a short distance to distribute
the sealing compound in the tire.
NOTE
Do not remove any foreign objects (nails,
etc.) from the tire before using the sealing
system.
•Stage 2: The tire’s inflation pressure is
checked and adjusted if necessary.
WARNING
•Never leave the tire sealing system
unattended when it is operating.
•Keep the tire sealing system away from
children.
•Be sure the vehicle is parked safely off
the road and away from moving traffic.
•Apply the parking brake.
Stage 1: Sealing the hole1. Open the cover on the tire sealing kit.2. Peel off the speed limit sticker and affix it
to the steering wheel hub where it will be
clearly visible to the driver.
3. Ensure that the on/off switch is in posi-
tion 0 (the 0 side of the switch should be
pressed down).
WARNING
Contact with the sealing compound may
cause skin irritation. If contact occurs, wash
the affected area immediately with soap and
water.
4. Unscrew the orange cover over the bottle
holder and unscrew the cap on the bottle
of sealing compound.
NOTE
Do not break the seal on the bottle. This
occurs automatically when the bottle is
screwed into the holder.
5. Screw the bottle into the bottle holder.

06 Maintenance and specifications
Vehicle care
06

277
CAUTION
•Avoid waxing or polishing plastic or rub-
ber components
•Polishing chromed strips can wear
away or damage the surface
•Polishes containing abrasive sub-
stances should not be used
Automatic car wash
•We do NOT recommend washing your car
in an automatic wash during the first six
months (because the paint will not have
hardened sufficiently).
•An automatic wash is a simple and quick
way to clean your car, but it is worth
remembering that it may not be as thor-
ough as when you yourself go over the car
with sponge and water. Keeping the under-
body clean is most important, especially in
the winter. Some automatic washers do
not have facilities for washing the under-
body.
CAUTION
•Before driving into an automatic car
wash, turn off the optional rain sensor to
avoid damaging the windshield wipers.
•Make sure that side view mirrors, auxil-
iary lamps, etc, are secure, and that any
antenna(s) are retracted or removed.
Otherwise there is risk of the machine
dislodging them.
•Chromed wheels: Clean chrome-
plated wheels using the same deter-
gents used for the body of the vehicle.
Aggressive wheel-cleaning agents can
permanently stain chrome-plated
wheels.
WARNING
•When the vehicle is driven immediately
after being washed, apply the brakes,
including the parking brake, several
times in order to remove any moisture
from the brake linings.
•Engine cleaning agents should not be
used when the engine is warm. This
constitutes a fire risk.
Exterior lightingCondensation may form temporarily on the
inside of the lenses of exterior lights such as
headlights, fog lights, or taillights. This is nor-mal and the lights are designed to withstand
moisture. Normally, condensation will dissi-
pate after the lights have been on for a short
time.
Polishing and waxing
•Normally, polishing is not required during
the first year after delivery, however, wax-
ing may be beneficial.
•Before applying polish or wax the vehicle
must be washed and dried. Tar spots can
be removed with kerosene or tar remover.
Difficult spots may require a fine rubbing
compound.
•After polishing use liquid or paste wax.
•Several commercially available products
contain both polish and wax.
•Waxing alone does not substitute for pol-
ishing a dull surface.
•A wide range of polymer-based waxes can
be purchased today. These waxes are easy
to use and produce a long-lasting, high-
gloss finish that protects the bodywork
against oxidation, road dirt and fading.
•Do not polish or wax your vehicle in direct
sunlight (the surface of the vehicle should
not be warmer than 113 °F (45 °C).

07 Index
07
294
E
ECC.................................................129, 130
Economical driving.................................. 204
Electric parking brake.............................. 117
Electronic Climate Control.......128, 129, 130
air distribution table............................ 131
Interior Air Quality System.................. 130
Emergency brake lights............................. 90
Emergency locking retractor...................... 36
Emergency starting.................................. 108
Emergency towing...........................221, 222
Emission inspection readiness................ 227
Engine
overheating........................................... 76
specifications...................................... 285
starting................................................ 106
switching off....................................... 108
Engine compartment overview................229
Engine oil
checking............................................. 230
low pressure warning light.............. 75, 76
specifications...................................... 287
volumes.............................................. 288
Environment............................................... 11Eyelets for anchoring loads..................... 213
F
Federal Clean Air Act............................... 226
Fluid specifications.................................. 288
Fog lights
front...................................................... 75
front/rear............................................... 90
rear...................................................... 238
Four C (active chassis system)................158
Front airbags.............................................. 20
disconnecting passenger’s side air-
bag.................................................. 24, 25
Front fog lights..................................... 75, 90
Front park assist.............................. 188, 190
Front seats...........................................81, 83
Fuel filler cap........................................... 210
Fuel filler door, opening........................... 210
Fuel level warning light.............................. 75
Fuel requirements............................ 208, 209
Fuel tank volume.....................................288
Fuses............................... 247, 248, 251, 253
G
Gasoline requirements............................. 209
Gas tank volume...................................... 288
Gauges...................................................... 73
Geartronic................................................ 111
Geartronic automatic transmission.......... 111
Generator warning light............................. 76
Glossary of tire terminology..................... 262
Grocery bag holder.................................. 214
Gross vehicle weight...............................262
H
Hazard warning flashers............................ 91
HD digital radio........................................ 138
Headlights
Active Bending Lights........................... 89
changing bulbs...........................235, 236
high/low beams.................................... 88
high beam flash.................................... 88
Headlight washers..................................... 95
Head restraints, rear seat.......................... 85
Heartbeat sensor (alarm system).........57, 58

07 Index
07
296
Malfunction indicator light......................... 74
Menu system........................................... 122
overview.............................................. 122
Messages in the instrument panel........... 124
Mirrors
defroster............................................. 100
power door........................................... 99
rearview, auto-dim function................ 100
retractable............................................. 99
vanity.................................................. 200
Motor oil
checking............................................. 230
specifications...................................... 287
volumes.............................................. 288
N
Net in cargo area..................................... 216
O
Occupant safety........................................ 14
Occupant weight sensor...................... 24, 25
Octane recommendations.......................209Odometer, trip........................................... 78
Oil
specifications...................................... 287
volumes.............................................. 288
On Call Roadside Assistance.................. 290
Overhead courtesy lighting........................ 92
Overheating, engine................................... 76
Oxygen sensors, heated.......................... 211
P
Paint, touching up.................................... 279
Park assist.......................................188, 190
Park Assist Camera................................. 191
Parking brake
electric, applying/releasing................. 117
warning light......................................... 76
Parking lights............................................. 89
Personal Car Communicator, unique func-
tions........................................................... 57
Polishing.................................................. 277
Power front seat
memory function................................... 82
with keyless drive................................. 83Power mirrors............................................ 99
defroster............................................. 100
Power steering
fluid..................................................... 233
speed-dependent............................... 158
Power steering fluid................................. 288
Power tailgate.......................................... 212
Power windows......................................... 97
laminated glass..................................... 98
Pregnancy, using seat belts during........... 18
PROPOSITION 65 WARN-
ING..................................... 11, 108, 246, 289
R
Radio
Sirius satellite radio............................141
Radio functions........................................ 135
HD digital radio................................... 138
Rain sensor................................................ 94
READ button............................................ 124
Rear fog light..................................... 90, 238
Rear park assist............................... 188, 190
Rear seat head restraints........................... 85