wheel VOLVO XC90 2014 Owner´s Manual
[x] Cancel search | Manufacturer: VOLVO, Model Year: 2014, Model line: XC90, Model: VOLVO XC90 2014Pages: 308, PDF Size: 13.31 MB
Page 70 of 308
02 Instruments and controls
Lighting panel
02
68
wheel (see the right-pointing beam in the illustration).
NOTE
When driving in daylight conditions, the headlights will switch off and the daytimerunning lights will come on. In darkness,the daytime running lights will switch offand the Active Bending Lights will switchon.
The ABL function is activated automatically when the engine is started and the headlight switch is in the
position and can be
deactivated/reactivated by pressing the but- ton in the center console (see page 64.
LED Daytime Running Lights (DRL)
To help conserve fuel by reducing the use of electrical current in the vehicle, DRL can beused in daylight conditions instead of the lowbeam headlights, which consume more elec-trical current. The daytime running lights aremounted in the front spoiler and use bright,electricity-saving LEDs (light emitting diodes).
Press button A to activate automatic DRL in day-
light driving conditions
With the headlight switch in the
posi-
tion as shown in the illustration, press the button with the A symbol to activate the auto-
matic LED daytime running lights in daylightdriving conditions (the indicator light in thebutton will illuminate). A light sensor thenmonitors the ambient lighting conditions andautomatically switches from LED DRL to thelow beam headlights in weaker ambient light(and will switch back to DRL when the ambi-ent light becomes brighter). Press the buttonagain (the indicator light in the switch will turnoff) to switch on the headlights. The LED DRLs will also switch off automati-cally (and the low beams will switch on) if:
• The rear fog light is switched on
• The windshield wipers are switched on for more than 10 seconds
If the LED DRL function was activated when the ignition was switched off, it will be activewhen the ignition is switched on again.
WARNING
• DRL is a driving aid designed to help conserve electrical current. This sys-tem cannot always determine if theambient lighting conditions are suffi-cient for switching from low beams toDRL (or vice versa). It is always thedriver's responsibility to visually deter-mine if the low beam headlights shouldbe used.
• As the driver, you have full responsibil-ity for operating the vehicle in a safemanner.
Page 71 of 308
02 Instruments and controls
Lighting panel
02
69
Parking lights
The front and rear parking lights can be turned on even when the ignition is switchedoff.
–Turn switch (1) to position .
The license plate lights also illuminate when the parking lights are switched on.
Rear fog light
The single rear fog light is located in the driv- er's side of the vehicle. The rear fog light will only function in combi- nation with the high/low beam headlights.
1. Turn the ignition key to position II.
2. Press button (3) to turn on the rear fog light.
An indicator light in the button illuminates when the rear fog light is on.
NOTE
The rear fog light is considerably brighter than the normal tail lights and should beused only when conditions such as fog,rain, snow, smoke or dust reduce visibilityfor other vehicles to less than 500 ft.(150 meters).
Instrument panel lighting
The instrument panel lighting illuminates when the ignition key is in position II and the light switch (1) is in either position
or
.
–Move the thumb wheel (4) up to increase brightness or down to decrease bright-ness.
Unlocking the fuel filler door
Press button (5) when the vehicle is at a standstill to unlock the fuel filler door. Pleasenote that the fuel filler door will remainunlocked until the vehicle begins to move for-ward. An audible click will be heard when thefuel filler door relocks.
NOTE
If the fuel filler door does not unlock after the button has been pressed, drive thevehicle at a speed of at least 5 mph(8 km/h), stop the vehicle, and press thebutton again.
For information on unlocking the fuel filler door manually, see page 70.
Page 73 of 308
02 Instruments and controls
Left-side steering wheel lever
02
71
Lever positions
G026954
Turn signals, lane change position
Turn signals, position for normal turns
High beam flash
Toggle between high and low beams, Home Safe lighting
Turn signals
When turningMove the lever as far up or down as possible (to position 2) to start the turn signals. Theturn signals will be cancelled automatically bythe movement of the steering wheel, or thelever can be returned to its initial position byhand.
When changing lanesThe driver can automatically flash the turnsignals 3 times by:• Moving the turn signal lever up or down to position (1) and releasing it.
• Moving the lever up or down to position(2) and immediately back to its originalposition.
NOTE
• This automatic flashing sequence can be interrupted by immediately movingthe lever in the opposite direction.
• If the turn signal indicator flashesfaster than normal, check for aburned-out turn signal bulb.
High/low beam headlights
Continuous high beams1. Turn the ignition key to position
II.
2. With the light switch in position
,
(see page 67) pull the turn signal lever toward the steering wheel to togglebetween high and low beams.
High beam flash1. Turn the ignition key to position II.
2. Pull the turn signal lever to position (3). The high beams will remain on until thelever is released.
Home safe lightingWhen leaving your vehicle at night, home safelighting can illuminate the area in front of thevehicle.
1. Remove the key from the ignition switch.
2. Pull the turn signal lever as far as possibletoward the steering wheel and release it.
3. Exit the vehicle and lock the doors.The headlights and parking lights will illumi- nate and remain on for 30 1
, 60 or 90 seconds.
The time interval can be changed by a trained and qualified Volvo service technician.
1 Factory setting
Page 74 of 308
02 Instruments and controls
Right-side steering wheel lever
02
72
Windshield wipers
G026953
Thumb wheel
Rain sensor on/off
Windshield wipers offIf the lever is in the 0 position and
you move it upwards, the wipers will sweep one stroke at a time foras long as you hold the lever up.
Single sweep positionMove the lever slightly upward from the 0 position for one sweep
of the wipers. The lever returnsautomatically to 0 when released.
Intermittent wiper functionWith the lever in this position, you can set the wiper interval bytwisting the control ring (1)upward to increase wiper speedor downward to decrease the
speed.
Windshield washer/headlight washer (certain models)
When the lever is pulled to wash the wind- shield, high pressure jets mounted in thebumper will spray the headlights.
CAUTION
• Use ample washer fluid when washing the windshield to avoid scratching theglass. The windshield should be thor-oughly wet when the wipers are inoperation.
• Before using the wipers, ice and snowshould be removed from the wind-shield/rear window. Be sure the wiperblades are not frozen in place.
•
To conserve washer fluid in driving condi- tions where the windshield washers areused frequently, the headlights will onlybe washed once for every five times the windshield is washed within a 10-minuteperiod.
• A short pull on the lever will wash thewindshield only.
• When approximately 1 US quart (1 liter)remains in the washer fluid reservoir, theheadlights will not be washed when thelever is pulled to conserve washer fluidfor the windshield. A text message willalso be displayed to remind the driver tofill the washer fluid reservoir.
Continuous wiper functionTop arrow:
normal speed
Bottom arrows: higher speed
Page 75 of 308
02 Instruments and controls
Right-side steering wheel lever
02
* Option/accessory, for more information, see Introduction.73
Tailgate wiper/washer
G027127
Intermittent wiping: Press the upper
section of the switch
Neutral position: The wiper is
switched off
Normal (continuous) wiping: Press the
lower section of the switch
Move the lever forward to start the tailgate washer. After washing the rear window, thewiper will make several additional sweeps.
Tailgate wiper and reverse gearIf the front wipers are on and the transmissionis put into reverse gear, the tailgate wiper will go into intermittent wiping function 1
.
If the tailgate wiper is already in normal wip- ing function, the normal wiping function willcontinue.
Rain sensor*
The rain sensor automatically regulates wiper speed according to the amount of water onthe windshield. The sensitivity of the sensor can be adjusted
by twisting ring (1) up (the wipers will sweep the windshield more frequently) or down (thewipers will sweep the windshield less fre-quently).
Activating the rain sensor:1. Turn the ignition key to at least position I
and put the windshield wiper lever inposition 0.
2. Press button (2), see page 72. > A light in the button will light up to indi-cate that the rain sensor is active.
Deactivating the rain sensor:
• Press button (2), see page 72. or •
Move the windshield wiper lever
down to
another position. Moving the lever up will not deactivate the rain sensor. Doing sowill cause the wipers to sweep the wind-shield until the lever is released, at whichtime the wipers return to rain sensormode.
The rain sensor is also deactivated when the key is removed from the ignition.
CAUTION
The rain sensor should be deactivated when washing the vehicle in an automaticcar wash, etc. If the rain sensor function isleft on, the wipers will start inadvertently inthe car wash and could be damaged.
1 Consult your Volvo retailer if you would like to have this function deactivated.
Page 76 of 308
02 Instruments and controls
Right-side steering wheel lever
02
74* Option/accessory, for more information, see Introduction.
IR-reflecting windshield*
Section of the windshield where the IR-coating is not applied
An optional factory-installed infrared (IR) coa- ting can be applied to the windshield to helpprotect the cabin from the sun's heat and thefading effect of sunlight on upholstery, pan-els, etc. Electronic equipment such as garage door openers, electronic toll tags and similar devi-ces should not be placed on sections of thewindshield with the IR coating because thiscould affect their function and limit theirrange. For best performance, place the device on the section of the windshield without the IR coating (see the area marked in the illustra-tion).
Page 78 of 308
02 Instruments and controls
Trip computer
02
76* Option/accessory, for more information, see Introduction.
Trip computer*
G026956
READ (press to acknowledge/confirm/
erase a message)
Thumb wheel (used to scroll among the trip computer menus)
RESET
The trip computer stores information gath- ered from several systems in your vehicle andhas four menus that can be displayed in thetext window.
• Driving distance on current fuel reserve
• Average fuel consumption
• Current fuel consumption
• Average speed •
Current speed in mph (Canadian models only)
• DSTC (see page 158 for detailed infor-mation)
NOTE
Warning messages from the vehicle's monitoring systems will override the tripcomputer function. If a warning message isdisplayed in the text window while you areusing the trip computer, you mustacknowledge the message by pressingbutton
A. Press button A again to return to
the trip computer function.
1. Trip computer controls and functionsThe trip computer functions can be accessed by twisting INFO (B ) one step at a time in
either direction. Twisting a final time returnsyou to the original function. The trip computer can be reset (current data will be erased from system memory) bypressing RESET (button C).
2. Driving distance on current fuel
reserve
This function shows the approximate dis-tance that can be driven on the fuel remainingin the tank. The calculation is based on aver-age fuel consumption during the last 20 miles(30 km) of driving and the amount of fuel remaining in the tank when the reading wastaken. When
"----" is displayed in the text window,
refuel as soon as possible.
3. Average fuel consumptionThis value indicates fuel consumption since the last time the trip computer was reset (bypressing RESET, button C). When the engine
is switched off, information on fuel consump-tion is stored and remains in system memoryuntil the RESET (button C) is pressed again.
4. Current fuel consumptionThis value indicates the current fuel con-sumption, based on readings taken once persecond. When the vehicle is not moving,"----" will be displayed.
5. Average speedThis value indicates average speed since thelast time the trip computer was reset (bypressing RESET, button C). When the engine
is switched off, information on average speedis stored and remains in system memory untilthe RESET (button C) is pressed again.
Page 80 of 308
02 Instruments and controls
Cruise control
02
78
Engaging the cruise control function
G027098
The cruise control panel is located on the left side of the steering wheel hub.
NOTE
This does not set the vehicle's speed.
1. Press the CRUISE button.
>
CRUISE will be displayed in the infor-
mation window in the instrument panel.
2. Press + or – to set the current speed.
>
CRUISE-ON will be displayed in the
information window in the instrument panel.
Increasing or decreasing speed
G027139
Use + or – in the following ways to increase
or decrease the vehicle's speed:
1. Press and hold down + or – until the vehi-
cle reaches the desired speed.
2. Press + or – for approximately a half sec-
ond and release the button to increase or decrease vehicle speed by approximately1 mph (1.6 km/h).
NOTE
Cruise control will not function at speeds below 20 mph. (30 km/h).
Braking
• Cruise control is automatically disen- gaged when the brake pedal isdepressed. The currently set speed isstored in memory.
• Pressing resume
will return the vehicle
to the previously set speed.
AccelerationMomentary acceleration, such as when pass- ing another vehicle, does not affect cruisecontrol operation. The vehicle will automati-cally return to the previously set speed whenyou release the accelerator pedal.
Disengaging cruise controlTo disengage cruise control, press the CRUISE button. CRUISE or CRUISE-ON will
no longer be displayed in the information win- dow in the instrument panel.
Page 81 of 308
02 Instruments and controls
Cruise control
02
79
NOTE
Cruise control is automatically disengaged if:
• When the brake pedal is depressed.
• the engine is switched off
• the gear selector is placed in (
N) Neu-
tral
• the wheels start to spin or lock
• if an increase in speed is maintained for more than one minute
• if the vehicle's speed falls belowapproximately 20 mph (30 km/h).
Temporarily disengaging the cruise control
1. Press
0 to temporarily disengage cruise
control. >
CRUISE will be displayed in the infor-
mation window in the instrument panel.
2. Depress the brake pedal. Pressing "resume"
causes the vehicle to
return to the previously set speed.
WARNING
Cruise control should not be used in heavy traffic or when driving on wet or slipperyroads, or when driving on unpaved oruneven road surfaces. Cruise control maynot maintain set speed on steep down-grades.
Page 121 of 308
04 Interior
Securing cargo
04
119
G027031
As a safety precaution, all cargo in your vehi- cle should be securely anchored to keep itfrom being thrown forward in the event ofsudden braking, etc. The vehicle is equippedwith eyelets in the cargo space to whichstraps or other cargo restraints can beattached.
WARNING
The eyelets are not to be used as passen- ger restraints or as anchorages for childrestraints.
Consult your Volvo retailer about suitable accessories for this purpose.Remember that an object weighing 44 lbs(20 kg) produces a force of 2,200 lbs(1,000 kg) in a head-on collision at 30 mph(50 km/h)! Keep the following in mind when loading the vehicle:
• The load carrying capacity of your vehicle is determined by factors such as thenumber of passengers, the amount ofcargo, the weight of any accessories thatmay be installed, etc. See the section"Vehicle loading" in the chapter "Wheeland tires" for more detailed information.
• Load the cargo
against the backrest.
• Load heavy cargo as low as possible.
• If no one is sitting in the outboard rearseat(s), reinforce the backrest by fasten-ing the seat belts.
• Never load cargo above the backrestwithout a cargo net.
WARNING
When the rear backrest(s) are folded down, the vehicle should not be loaded toa level higher than 2 in. (5 cm) below theupper edge of the rear side windows.Objects placed higher than this level couldimpede the function of the inflatable cur-tain.
G027058
Attachment bracket
Nylon cargo net (accessory)The Volvo XC90 can be equipped with a cargo net made of strong nylon fabric. This net can be installed in two places:
• Behind the rear seat backrests (the sec- ond row of seats)
• Behind the front seat backrests if the rearseat backrests (the second row of seats)have been folded down.