warning VOLVO XC90 TWIN ENGINE 2018 Owners Manual

LOADING, STORAGE AND PASSENGER COMPARTMENT
* Option/accessory.
584 Using the electrical outlets
The 12 V outlet can be used for devices
intended for this such as MP3 players, coolers
and cellular phones.
The high-voltage outlet* can be used for devices
intended for this, such as chargers, laptops, etc. The ignition must be in at least mode I for the
outlets to supply current. The outlets will then be
active as long as there is sufficient charge in the
start battery.
If the engine is turned off and the vehicle is
locked, the outlets will be deactivated. If the
engine is turned off and the vehicle remains
unlocked, the sockets will remain active for up to
7 minutes.
NOTE Bear in mind that using the electrical outlets
when the engine is off could cause the starter
battery to have too low of a charge level,
which could limit other functionality.
Accessories connected to the electrical out-
lets can be activated even when the vehicle
electrical system is off or if preconditioning is
used. For this reason, disconnect plugs when
they are not in use to prevent the starter bat-
tery from becoming discharged.
WARNING •
Do not use accessories with large or
heavy plugs – they could damage the out-
let or come loose while you are driving.
• Do not use accessories that could cause
disruptions to e.g. the vehicle's radio
receiver or electrical system.
• Position the accessory so that there is no
risk of it injuring the driver or passengers
in the event of heavy braking or a colli-
sion.
• Pay attention to connected accessories
as they can generate heat that could burn
passengers or the interior.
Using 12 V outlets1. Remove the stopper (tunnel console) or fold
down the cover (trunk/cargo compartment)
over the socket and plug in the device.
2. Unplug the device and put the stopper back in (tunnel console) or fold up the cover
(trunk/cargo compartment) when the socket
is not in use or left unattended.
CAUTION The maximum power is 120 W (10 A) per
outlet.
Using high-voltage outletsThe ignition must be in at least mode I for outlets
to supply current. The outlets will then be active
as long as there is sufficient charge in the start
battery.
1. Slide down the cover over the outlet and plug
in the device.
>
The LED 2
light on the outlet will indicate
its status.
2. The outlet is supplying electrical current when the light is glowing steadily green.
3. Disconnect the device by pulling out the plug (do not pull on the cord).
Pull up the cover when the outlet is not in
use or is left unattended.
CAUTION The maximum power is 150 W.
WARNING
Do not attempt to alter or repair the high-volt-
age outlet on your own. Volvo recommends
contacting an authorized Volvo workshop.
2
LED (Light Emitting Diode)

LOADING, STORAGE AND PASSENGER COMPARTMENT
585
WARNING•
Only use accessories that are not dam-
aged or malfunctioning. The accessories
must be designed for 120 V and 60 Hz,
with plugs intended for the outlet. The
accessories must be CE marked, UL
marked or have an equivalent safety
marking.
• New let outlets, plugs or accessories
come into contact with water or another
fluid. Do not touch or use the outlet if it
appears damaged or has been in contact
with water or another fluid.
• Do not connect power strips, adapters or
extension cords to the outlet has this
could cause the outlet's safety functions
to malfunction.
• The outlet is equipped with a pet guard.
Make sure that no one picks at or dam-
ages the outlet in such a way that the
guard is disabled. Children should not be
left unsupervised in the vehicle when the
outlet is active.
Failure to follow the above could lead to
severe or fatal electrical shocks.
Related information
• Electrical outlets (p. 582)
• Passenger compartment interior (p. 580) Using the glove compartment
The glove compartment is located on the pas-
senger side. The glove compartment can be
used to store the Owner's Manual, maps, etc.
There is also room for a pen and a card holder. Glove compartment and opening button on the center
console.
The glove compartment is opened by pressing
the opening button in the center console.
Locking and unlocking the glove box
The glove compartment can be locked ("private
locking") when the vehicle is left at a workshop,
hotel, etc. When private locking is activated, the
tailgate is also locked.
Using the glove box as a cooled area
The glove compartment can be used to cool e.g.
drinks or food. Cooling is possible when the cli-
mate system is active (i.e. when the ignition is in
mode II or when the engine is running). The illustration is generic – the design may vary.
Activate cooling
Deactivate cooling
– Activate or deactivate cooling by moving the
control as far as possible toward the passen-
ger compartment/glove compartment.
Related information
•
Passenger compartment interior (p. 580)
• Private Locking (p. 266)

LOADING, STORAGE AND PASSENGER COMPARTMENT
* Option/accessory.
586 Sun visors
In the ceiling in front of the driver and front pas-
senger, there are sun visors that can be lowered
and angled to the side as necessary.
The illustration is generic – the design may vary.
The mirror lighting* comes on automatically when
the cover is lifted up.
The mirror frame has a holder for e.g. cards or
tickets.
Related information
• Passenger compartment interior (p. 580) Cargo compartment
The vehicle has a flexible cargo compartment
that makes it possible to carry and secure large
objects.
The cargo compartment capacity can be consid-
erably increased by folding down the backrests in
the second and third rows* of seats. To make
loading and unloading easier, the rear section of
the vehicle can be raised and lowered using the
level control function*. Use the load anchoring
eyelets or grocery bag holders to help secure
objects in place, and the retractable cargo com-
partment cover* to help conceal objects in the
cargo compartment.
If the vehicle is equipped with a temporary spare
tire, this is secured to the cargo compartment
floor under the cover. The towing eyelet and tire
sealing system are located under the cargo com-
partment floor.
Related information
• Loading recommendations (p. 586)
• Grocery bag holders (p. 588)
• Load anchoring eyelets (p. 589)
• Installing and removing the cargo compart-
ment cover* (p. 589) Loading recommendations
There are a number of things to consider when
carrying loads in or on the vehicle. Load-carrying capacity is determined by the vehi-
cle's curb weight. The total weight of all passen-
gers and any installed accessories reduces the
vehicle's load-carrying capacity by the corres-
ponding amount.
WARNING The vehicle's driving characteristics change
depending on the weight and position of the
load.
Loading in the trunk and cargo
compartment
•
Position objects so they are pressing against
the rear seat backrests.
• Distribute the load evenly.
• Heavy objects should be positioned as low
as possible. Avoid placing heavy objects on
folded-down seat backrests.
• Cover sharp corners with a soft cloth or simi-
lar to help prevent damage to the upholstery.
• Use the load anchoring eyelets and tension-
ing straps or similar to secure all objects.

LOADING, STORAGE AND PASSENGER COMPARTMENT
* Option/accessory.587
WARNINGIn a head-on collision at a speed of 50 km/h
(30 mph), an unsecured object weighing 20
kg (44 pounds) can reach a projectile weight
equivalent to 1000 kg (2200 pounds).
WARNING
If objects are loaded higher than the upper
edge of the side windows, leave a 10 cm (4
in.) space between the objects and the win-
dow. Objects placed closer to this could
impede the function of the inflatable curtain
concealed inside the headlining.
WARNING
Always secure the load. Otherwise, it may shift
during heavy braking and injure people in the
vehicle.
Cover sharp edges and sharp corners with
something soft.
Turn off the engine and apply the parking
brake when loading/unloading long objects.
Otherwise, it is possible for the load to reach
the gear lever or gear selector and move it to
a drive position – which could cause the vehi-
cle to begin rolling.
Extra cargo space
The rear seat backrests can be folded down to
increase cargo compartment space and simplify
loading. If the rear seat backrests are folded down, make sure that no objects loaded into the
vehicle prevent the WHIPS system for the front
seats from functioning correctly.
Raising/lowering the rear end of the
vehicle*
The rear end of the vehicle can be lowered or
raised for easier loading or to facilitate attaching
a trailer*.
The controls for raising/lowering are located at
the rear edge of the cargo compartment's right
side panel. Controls for raising/lowering the rear end of the vehicle.
The controls consist of two buttons ‒ one button
for lowering and one button for raising the rear
end. Press and hold the relevant button until the
desired height is reached.
The rear end of the vehicle cannot be raised
higher than its normal height. The rear end will return to the normal height
when the vehicle begins driving.
NOTE It is not possible to adjust the height of the
vehicle's rear when one or more of the doors
or the hood is open. This does not apply to
the tailgate.
WARNING
Make sure that no people, animals or objects
are found under the vehicle when it is low-
ered. This could endanger life and cause
damage to the vehicle or objects.
Related information
•
Load anchoring eyelets (p. 589)
• Folding the second row backrests (p. 192)
• Roof loads and load carriers (p. 588)
• Leveling control* and suspension (p. 450)
• Weights (p. 659)

LOADING, STORAGE AND PASSENGER COMPARTMENT
* Option/accessory.
588 Roof loads and load carriers
Volvo-developed load carriers are recommended
for carrying loads on the roof of the vehicle.
Volvo load carriers are specially designed to help
prevent damage to your vehicle and help ensure
maximum safety while driving. Volvo load carriers
are available from authorized Volvo retailers.
Carefully follow the installation instructions provi-
ded with the load carriers.
•
Check periodically to ensure that the load
carriers and load are properly secured.
Secure the load firmly using tie straps or
similar.
• Distribute the load evenly throughout the
load carriers. Place heavier cargo at the bot-
tom of the load.
• The vehicle's wind resistance and fuel con-
sumption increase with the size of the load.
• Drive smoothly. Avoid rapid acceleration, hard
braking and fast cornering.
WARNING The vehicle's center of gravity and driving
characteristics are altered by roof loads.
Follow the vehicle's specifications regarding
weights and maximum permitted load.
Related information
•
Loading recommendations (p. 586)
• Weights (p. 659) Grocery bag holders
Grocery bag holders (hooks) help keep shop-
ping bags in place and prevent them from falling
over and spilling their contents in the cargo
compartment.
On the sides of the cargo compartment
There are two fold-out holders in the side panels,
one on each side of the cargo compartment.
CAUTION
The grocery bag holders are only intended to
hold weights up to 5 kg (11 lbs).
Related information
•
Loading recommendations (p. 586)
• Installing and removing the cargo net*
(p. 593) •
Installing and removing the cargo compart-
ment cover* (p. 589)
• Installing and removing the steel cargo grid*
(p. 592)

LOADING, STORAGE AND PASSENGER COMPARTMENT
* Option/accessory.589
Load anchoring eyelets
The fold-out eyelets in the cargo compartment
can be used to secure objects with straps, a net,
etc.
WARNING Hard, sharp and/or heavy objects in or pro-
truding from the vehicle can cause injury in
the event of hard braking.
Always secure large and heavy objects with a
seat belt or cargo retaining straps.
Related information
•
Loading recommendations (p. 586)
• Weights (p. 659) Installing and removing the cargo
compartment cover*
The cover can be rolled out to conceal objects
in the cargo compartment.
Installing the cargo compartment
cover 3 Press the end piece on one side of the cover
into the retaining bracket in the side panel of
the cargo compartment.
Then put the other end piece in the recess in
the side panel on the opposite side. Push the end piece down on both sides, one
at a time.
>

When a click is heard and the red marks
on each end piece are no longer visible,
the cover is in place. Check that it is
secure.
Removing the cargo compartment
cover
In retracted position:
1. Press the button on one of the cover's ends and lift out that end.
For 7-seat models - remove the third row
seat belt latches from the hooks above the
side panels.
2. Carefully lift the cover up and out. > The other end will release automaticallyand the cover can then be lifted out of the
cargo compartment.
Related information
• Operating the cargo compartment cover*
(p. 590)
• Loading recommendations (p. 586)
3
In the XC90 Excellence, the cargo compartment cover is permanently fixed\
and cannot be taken out or put in.

LOADING, STORAGE AND PASSENGER COMPARTMENT
* Option/accessory.591
Loading modeFrom the fully retracted position - grasp the
handle and pull the cover up and over the
side panels in the cargo compartment. Pull to
the end position and press the attaching pins
at the end of the cover into the grooves in
the side panels of the vehicle. (If the cover is
already fully open, see next section.)
From the fully open position - grasp the han-
dle and press the cover's attaching pins
down into the grooves in the side panels and
then release.
>

Retract the cover until it stops in the parti-
ally retracted position. If your hands are full: In the fully open position, push the cover's
handle slightly upward with e.g. your elbow.
>
The cover will retract until it stops in
the partially retracted position.
To fully open the cover from the partially retrac-
ted position:
1.

Grasp the handle and pull the cover out as
far as possible.
2. Let the cover retract slightly and press the handle slightly downward.
> The cover will be secured in the fully openposition.
CAUTION Do not place objects on top of the cargo
compartment cover.
WARNING In 7-seat models - never have a cargo com-
partment cover mounted when there are pas-
sengers in the rear seats. This could lead to
serious injury in the event of a collision.
Retracting the cover
1. From the fully opened position:
Lift the cover's handle and pull it rearward to
release the cover's attaching pins from the
grooves. Let the cover retract.
From the partially retracted position:
Grasp the handle and pull the cover out of
the groves to the fully open position. Lift the
handle and pull it rearward to release the
cover's attaching pins from the grooves. Let
the cover retract.
2. Let the cover retract with its attaching pins above the side panels until it stops in the
fully retracted position.
Related information
• Installing and removing the cargo compart-
ment cover* (p. 589)

LOADING, STORAGE AND PASSENGER COMPARTMENT
* Option/accessory.
592 Installing and removing the steel
cargo grid*
The steel cargo grid prevents loads or pets in
the cargo compartment from being thrown for-
ward into the passenger compartment. For safety reasons, the steel grid must always be
installed and secured correctly.
WARNING
Under no circumstances may a person be in
the cargo compartment when the vehicle is
moving. Heavy braking or a collision could
lead to serious injury.
The steel grid consists of the grid itself and two
separate mounting brackets. Each of the mount- ing brackets has a screw cover and two plastic
sleeves for the grid.
WARNING The steel cargo grid may only be used in the
rear position described here. The ceiling
attachment points behind the front seats are
not intended to anchor the steel grid.
WARNING
For safety reasons, the third-row seats
4
must
be folded down when the steel cargo grid is
mounted in the vehicle.
CAUTION The steel cargo grid and the cargo compart-
ment cover cannot be mounted at the same
time.
Installation1. Fold down the rear seats and lift in the steel
grid through one of the rear doors or the tail-
gate. The curved (convex) side of the grid
should face toward the cargo compartment
and the hooks on each side of the grid
should face upward. The mounting brackets
and plastic sleeves are not needed in this
step. 2. Press one of the grid's hooks into the larger
hole in the ceiling attachment point (1).
Grasp the grid near the hook and pull/push it
into the smaller hole (2).
>

The hook is now secured in the attach-
ment point.
3. Repeat step 2 above to secure the other hook in the attachment point on the opposite
side.
WARNING Make sure the cargo grid's hooks are securely
attached in the ceiling attachment points to
help ensure the grid does not come loose.
4
7-seat models only.

||LOADING, STORAGE AND PASSENGER COMPARTMENT
594
WARNING
Objects in the cargo compartment must
always be securely anchored, even with a cor-
rectly installed cargo net.
Installing the cargo net
WARNING
All of the cargo net's upper consoles, hooks
and straps must be securely mounted and
attached before the net is used.
Never use the net if it is damaged.
NOTE
With front mounting, the cargo net is most
easily installed via a rear door.
1. Fold out the cargo net and make sure that
the upper rod folds out and locks into posi-
tion.
2.

Insert one of the net's hooks into the front or
rear ceiling mounting point with the strap
lock facing you. 3. Insert the other upper hook into the ceiling
mounting point on the opposite side. The
telescopic spring-loaded hooks make mount-
ing easier.
Make sure that the net's hooks are pushed
forward as far as possible into their respec-
tive mounting points. 4. Rear mounting: With the cargo net hooked
into the rear ceiling mounting points, attach
the net's straps into the front floor eyelets in
the cargo compartment. Rear mounting.
Front mounting: With the cargo net mounted
in the front ceiling mounting points, hook the
straps into the outer eyelets on the front seat
rails behind the seats. Attaching the net is
easier if the seat backrests are upright and
the seats are moved slightly forward.

MAINTENANCE AND SERVICE
598Volvo's service program
To keep the vehicle as safe and reliable as pos-
sible, follow the Volvo service schedule speci-
fied in the Warranty and Maintenance Records
Information booklet.
Volvo recommends having an authorized Volvo
workshop perform service and maintenance.
Volvo workshops have the staff, service literature
and special tools to guarantee the highest quality
of service.
CAUTION To ensure the Volvo warranty is not invalida-
ted, check and follow the Service and War-
ranty Booklet.
Service and repairsService the vehicle regularly. Follow Volvo's rec-
ommended service intervals.
Detailed inspection and repairs may only be per-
formed by an authorized workshop.
WARNING
Do not make any repairs on this vehicle your-
self. Electrical cables and/or components that
have come loose may only be corrected by an
authorized workshop – an authorized Volvo
workshop is recommended.
IntroductionThe maintenance services contain several checks
that require special instruments and tools and
therefore must be performed by a qualified tech-
nician. To keep your Volvo in top condition, spec-
ify time-tested and proven Genuine Volvo Parts
and Accessories.
The Federal Clean Air Act - U.S.
The Federal Clean Air Act requires vehicle manu-
facturers to furnish written instructions to the ulti-
mate purchaser to assure the proper servicing
and function of the components that control
emissions. These services, which are listed in the
"Warranty and Service Records Information"
booklet, are not covered by the warranty. You will
be required to pay for labor and material used.
Maintenance
Your Volvo passed several major inspections
before it was delivered to you, in accordance with
Volvo specifications. The maintenance proce-
dures outlined in the Warranty and Service
Records Information booklet, many of which will
positively affect your vehicle's emissions, should
be performed as indicated. It is recommended
that receipts for vehicle emission maintenance be
retained in case questions arise concerning
maintenance. Inspection and maintenance should
also be performed anytime a malfunction is
observed or suspected.
Applicable warranties - U.S./Canada
In accordance with applicable U.S. and Canadian
regulations, the following list of warranties is pro-
vided.
• New Vehicle Limited Warranty
• Parts and Accessories Limited Warranty
• Corrosion Protection Limited Warranty
• Seat Belt and Supplemental Restraint Sys-
tems Limited Warranty
• Emission Design and Defect Warranty
• Emission Performance Warranty
These are federal warranties. Other warranties
are provided as required by state/provincial law.
Refer to your separate Warranty and Service
Records Information booklet for detailed informa-
tion concerning each of the warranties.