wheel YAMAHA BLASTER 200 2002 User Guide

7-39
w
Always open the throttle gradually and
release the clutch lever slowly. Otherwise,
the machine could wheelie which would
increase the chance of an accident.
cC
Do not shift gears without releasing the
throttle. Damage to the engine or drive train
may occur.
When slowing down or stopping, release the
throttle and apply the brakes smoothly and
evenly. As you slow down, shift to a lower gear.
Be sure that the engine has sufficiently slowed
before engaging a lower gear. Improper use of
the brakes or shifting can cause the tires to lose
traction, reducing control and increasing the
possibility of an accident.
5KJ-62 (7 shou) 4/23/01 3:06 PM Page 40

7-41
w
Make sure the engine has sufficiently slowed
before shifting to a lower gear. Engaging a
lower gear when the engine speed is too
high could cause the wheels to stop rotating.
5KJ-62 (7 shou) 4/23/01 3:06 PM Page 42

7-43
TURNING YOUR ATV
To achieve maximum traction while riding off-
road, the two rear wheels are mounted solidly
on one axle and turn together at the same
speed. Therefore, unless the wheel on the
inside of the turn is allowed to slip or lose some
traction, the ATV will resist turning. A special
turning technique must be used to allow the ATV
to make turns quickly and easily. It is essential
that this skill be learned first at low speed.
w
Always follow proper procedures for turning
as described in this Owner’s Manual.
Practice turning at low speeds before
attempting to turn at faster speeds. Do not
turn at speeds too fast for your skills or the
conditions.
5KJ-62 (7 shou) 4/23/01 3:06 PM Page 44

1. Lean towards inside of turn.
2. Support your weight on the outer footrest.
1. Se pencher vers l’intérieur du virage.
2. S’appuyer sur le repose-pied externe.
1. Inclínese hacia el interior del giro.
2. Descanse su peso en el descansapie externo.
7-45
As you approach a curve, slow down and begin
to turn the handlebars in the desired direction.
As you do so, put your weight on the footboard
to the outside of the turn (opposite your desired
direction) and lean your upper body into the
turn. Use the throttle to maintain an even speed
through the turn. This maneuver will let the
wheel on the inside of the turn slip slightly,
allowing the ATV to make the turn properly.
This procedure should be practiced at slow
speed many times in a large off-road area with
no obstacles. If an incorrect technique is used,
your ATV may continue to go straight. If the ATV
doesn’t turn, come to a stop and then practice
the procedure again. If the riding surface is slip-
pery or loose, it may help to position more of
your weight over the front wheels by moving for-
ward on the seat.Once you have learned this
technique you should be able to perform it at
higher speeds or in tighter curves.
q
w
5KJ-62 (7 shou) 4/23/01 3:06 PM Page 46

7-55
If your ATV has stalled or stopped and you
believe you can continue up the hill, restart care-
fully to make sure you do not lift the front wheels
which could cause you to lose control. If you are
unable to continue up the hill, dismount the ATV
on the uphill side. Physically turn the ATV
around and then descend the hill.
If you start to roll backwards, DO NOT use the
rear brake to stop or try to put the ATV in gear.
The ATV could easily tip over backwards.
Instead, dismount the ATV immediately on the
uphill side.
5KJ-62 (7 shou) 4/23/01 3:06 PM Page 56

7-63
CROSSING A SLOPE
Traversing a sloping surface on your ATV
requires you to properly position your weight to
maintain proper balance. Be sure that you have
learned the basic riding skills on flat ground
before attempting to cross a sloping surface.
Avoid slopes with slippery surfaces or rough ter-
rain that may upset your balance.
As you travel across a slope, lean your body in
the uphill direction. It may be necessary to cor-
rect the steering when riding on loose surfaces
by pointing the front wheels slightly uphill. When
riding on slopes be sure not to make sharp turns
either up or down hill.
5KJ-62 (7 shou) 4/23/01 3:06 PM Page 64

7-73
SLIDING AND SKIDDING
Care should be used when riding on loose or
slippery surfaces since the ATV may slide. If
unexpected and uncorrected, sliding could lead
to an accident.
To reduce the tendency for the front wheels to
slide in loose or slippery conditions, positioning
your weight over the front wheels will sometimes
help.
If the rear wheels of your ATV start to slide side-
ways, control can usually be regained (if there is
room to do so) by steering in the direction of the
slide. Applying the brakes or accelerating is not
recommended until you have corrected the
slide.
5KJ-62 (7 shou) 4/23/01 3:06 PM Page 74

7-77
WHAT TO DO IF ...
This section is designed to be a reference guide
only. Be sure to read each section on riding
techniques completely.
WHAT TO DO ...
8If your ATV doesn’t turn when you want it to:
Bring the ATV to a stop and practice the turn-
ing maneuvers again. Be sure you are putting
your weight on the footboard to the outside of
the turn. Position your weight over the front
wheels for better control. (See pages 7-43 ~
7-47.)
8If your ATV begins to tip while turning:
Lean more into the turn to regain balance. If
necessary, gradually let off the throttle and/or
steer to the outside of the turn. (See pages
7-43 ~ 7-47.)
5KJ-62 (7 shou) 4/23/01 3:06 PM Page 78

8-8 * It is recommended that these items be serviced by a Yamaha dealer.
** Lithium soap base greaseINITIAL EVERY
ITEM ROUTINE 1 3 6 6 1
month months months months year
Drive chain9Lubricate, check free play and alignment.
2222
9Replace if necessary.
* Drive chain guard
9Check wear and replace if necessary.222
and rollers
* Steering system9Inspect free play, clean and lubricate.**22222
* Front and rear
9Inspect and lubricate.**22222
suspension
9Inspect air pressure, wheel runout, and tire wear.
Tire, wheels9*Inspect bearings.22222
9*Replace bearings if necessary.
Throttle, control cable9Check routing and connection.
22222
9*Lubricate.
Outside nuts and bolts9Retighten.22222
Frame9Clean and inspect.2222
Lighting equipment9Inspect.22222
5KJ-62 (8 shou) 4/23/01 3:08 PM Page 9

qw
a
a’
a = a’
1. Equalizer 2. Cable joint1.Égaliseur 2. Raccord de câble1. Ecualizador 2. Conexión del cable
8-51
EBU00524
Front brake lever free play adjustment
NOTE:
Before adjusting the brake, inspect the front
brake shoes.
The front brake lever free play should be adjust-
ed to 3 ~ 5 mm at the brake lever pivot. If the
free play is incorrect, adjust as follows:
1. Loosen the locknut and fully turn in the
adjusting bolt at the front brake lever.
2. Make sure the cable joint in the equalizer is
straight when the brake is applied. If not,
turn the adjusting nuts at the front wheel
hubs until the cable joint becomes straight.
3. Turn the adjusting bolt at the brake lever
until specified free play is obtained.
wqa
1. Adjusting bolt 2. Locknut a. Free play1. Boulon de réglage 2. Contre-écrou a. Jeu1. Perno de ajuste 2. Contratuerca a. Juego libre
Specified free play: 3 ~ 5 mm
5KJ-62 (8 shou) 4/23/01 3:08 PM Page 52