brake YAMAHA BLASTER 200 2002 Owner's Guide

8-71
EBU00737
Brake and shift pedal/brake and clutch lever
lubrication
Lubricate the pivoting parts of each lever and
pedal.
EBU00793
Upper arm and lower arm pivot lubrication
Lubricate the upper arm pivot and the lower arm
pivot.
Recommended lubricant:
Lithium-soap-based grease
(all-purpose grease)
Recommended lubricant:
Lithium-soap-based grease
(all-purpose grease)
5KJ-62 (8 shou) 4/23/01 3:08 PM Page 72

8-81
EBU00861
Tail/brake light bulb replacement
1. Remove the bulb holder (together with the
bulb) by turning it counterclockwise.
2. Remove the defective bulb from the bulb
holder by pushing it inward and turning it
counterclockwise.
3. Install a new bulb in the bulb holder by
pushing it inward and turning it clockwise.
4. Install the bulb holder (together with the
bulb).
q
q
w
1. Bulb holder1. Fixation d’ampoule1. Portabombillas
1. Bulb holder 2. Bulb
1. Fixation d’ampoule 2. Ampoule
1. Portabombillas 2. Bombilla
5KJ-62 (8 shou) 4/23/01 3:08 PM Page 82

9-3
cC
Excessive water pressure may cause water
seepage and deterioration of wheel bearings,
brakes, transmission seals and electrical
devices. Many expensive repair bills have
resulted from improper high pressure deter-
gent applications such as those available in
coin-operated car washers.
4. Once the majority of the dirt has been hosed
off, wash all surfaces with warm water and
mild, detergent-type soap. An old tooth-
brush or bottle brush is handy for hard-to-
get-at places.
5. Rinse the machine off immediately with
clean water and dry all surfaces with a
chamois, clean towel or soft absorbent
cloth.
6. Dry the chain and lubricate it to prevent rust.
5KJ-62 (9 shou ~) 4/23/01 3:09 PM Page 4

9-5
7. Clean the seat with a vinyl upholstery clean-
er to keep the cover pliable and glossy.
8. Automotive type wax may be applied to all
painted and chrome plated surfaces. Avoid
combination cleaner-waxes. Many contain
abrasives which may mar the paint or pro-
tective finish.
When finished, start the engine and let it idle for
several minutes.
w
Wet brakes may have reduced stopping abili-
ty, increasing the chance of an accident.
Test the brakes after washing. Apply the
brakes several times at slow speeds to let
friction dry out the linings.
5KJ-62 (9 shou ~) 4/23/01 3:09 PM Page 6

10-4
Model YFS200
Gear ratio
1st 34/11 (3.091)
2nd 31/14 (2.214)
3rd 25/15 (1.667)
4th 20/16 (1.250)
5th 19/18 (1.056)
6th 19/21 (0.905)
Chassis:
Frame type Steel tube frame
Caster angle 9°
Trail 40 mm
Tire:
Type Tubeless
Size front AT21 ×7 - 10
rear AT21 ×10 - 8
Brake:
Front brake type Drum brake
operation Right hand operation
Rear brake type Single disc brake
operation Right foot operation
5KJ-62 (9 shou ~) 4/23/01 3:09 PM Page 15

10-5
Model YFS200
Suspension:
Front suspension Double wishbone
Rear suspension Swingarm (monocross)
Shock absorber:
Front shock absorber Coil spring/Oil damper
Rear shock absorber Coil spring/Gas-oil damper
Wheel travel:
Front wheel travel 180 mm
Rear wheel travel 180 mm
Electrical:
Ignition system C.D.I.
Generator system C.D.I. magneto
Headlight type: Bulb type
Bulb voltage, wattage ×quantity:
Headlight 12V, 45 W/45 W ×1
Tail/brake light 12V, 5/21 W ×1
Indicator light:
Oil level 12V, 3.4 W ×1
5KJ-62 (9 shou ~) 4/23/01 3:09 PM Page 16