recommended oil YAMAHA BLASTER 200 2004 Notices Demploi (in French)

5-13
EBU00134
Engine oil
Make sure the engine oil is at the specified level.
Add oil as necessary (see page 10-2).
NOTE:
Be sure to push the cap into the filler neck until it
is properly seated.
q
1. Oil tank filler cap1. Bouchon de remplissage de réservoir d’huile1. Tapa de llenado de depósito de aceite
Recommended oil:
Air-cooled 2-stroke engine oil
Oil quantity:
Total amount:
1.3 L
5VM-9-61-02 3/14/03 9:35 PM Page 50

5-15
EBU01308
Transmission oil
Make sure the transmission oil is at the specified
level. Add oil as necessary. (See pages 8-17–
8-23.)
cC
8In order to prevent clutch slippage (since
the transmission oil also lubricates the
clutch), do not mix any chemical additives.
Do not use oils with a diesel specification of
“CD” or oils of a higher quality than speci-
fied. In addition, do not use oils labeled
“ENERGY CONSERVING
II” or higher.
8Make sure that no foreign material enters
the crankcase.
Recommended oil:
SAE 10W30
Recommended oil classification:
API Service SE, SF, SG type or higher
Oil quantity:
Total amount:
0.7 L
Periodic oil change:
0.65 L
5VM-9-61-02 3/14/03 9:35 PM Page 52

8-9
NOTE:
8Recommended brake fluid: DOT 4
8Brake fluid replacement:
9When disassembling the master cylinders or caliper cylinders, replace the brake fluid.
Normally check the brake fluid level and add fluid as required.
9On the inner parts of the master cylinders and caliper cylinders, replace the oil seals every
two years.
9Replace the brake hoses every four years, or if cracked or damaged.
5VM-9-61-05 3/14/03 10:48 PM Page 10

EBU08371
Transmission oil
Transmission oil measurement
1. Place the machine on a level surface.
2. Warm up the engine for several minutes,
and stop it.
3. Check the oil level through the level window
located at the right side crankcase cover.
NOTE:
Wait a few minutes until the oil level settles
before checking.
4. The oil level should be between the mini-
mum and maximum marks. If the level is
low, add the recommended oil to raise it to
the proper level.
1
2
3
1
1. Level window
2. Maximum level mark 3. Minimum level mark
1. Hublot de contrôle du niveau d’huile
2. Repère de niveau maximum 3. Repère de niveauminimum
1. Mirilla del nivel
2. Marca de máximo 3. Marca de mínimo
8-17
5VM-9-61-05 3/14/03 10:48 PM Page 18

q
1. Drain bolt1. Boulon de vidange1. Perno de drenaje
8-19
Transmission oil replacement
1. Place the machine on a level surface.
2. Warm up the engine for several minutes,
and stop it.
3. Place a container under the engine to col-
lect the used oil.
4. Remove the oil filler cap and drain bolt to
drain the oil.
5. Install the drain bolt and tighten it to the
specified torque.
6. Fill the engine with the recommended oil
and install the filler cap.
1
1. Transmission oil filler cap1. Bouchon de remplissage d’huile1. Tapón de llenado del aceite
Tightening torque
Drain bolt:
20 Nm (2.0 m0kgf)
5VM-9-61-05 3/14/03 10:48 PM Page 20

8-21
cC
8In order to prevent clutch slippage (since
the transmission oil also lubricates the
clutch), do not mix any chemical additives.
Do not use oils with a diesel specification
of “CD” or oils of a higher quality than
specified. In addition, do not use oils
labeled “ENERGY CONSERVING
II” or
higher.
8Make sure that no foreign material enters
the crankcase.
Recommended oil:
See page 10-2.
Oil quantity:
Periodic oil change:
0.65 L
5VM-9-61-05 3/14/03 10:48 PM Page 22

8-81
EBU00570
Cable inspection and lubrication
w
Inspect cables frequently and replace if dam-
aged. Corrosion can result when the outer
covering of control cables becomes dam-
aged. Cables can also become frayed or
kinked. Operation of controls could be
restricted, which could cause an accident or
injury.
Lubricate the inner cables and the cable ends. If
the cables do not operate smoothly, ask a
Yamaha dealer to replace them.
Recommended lubricant:
Engine oil
5VM-9-61-05 3/14/03 10:48 PM Page 82

10-2
Model YFS200
Engine oil (2-cycle):
Type Air-cooled 2-stroke engine oil
Quantity 1.3 L
Transmission oil:
Type SAE 10W30 type SE motor oil
Recommended transmission oil
classificationAPI Service SE, SF, SG type or higher
cC
In order to prevent clutch slippage (since the
transmission oil also lubricates the clutch),
do not mix any chemical additives. Do not
use oils with a diesel specification of “CD” or
oils of a higher quality than specified. In
addition, do not use oils labeled “ENERGY
CONSERVING
II” or higher.
Quantity:
Periodic oil change 0.65 L
Air filter Wet type element
10
5VM-9-61-06 3/14/03 9:40 PM Page 13