light YAMAHA BLASTER 200 2007 Owner's Manual

8-36
1
2
3
4
5
6
78
9
10
11

EBU25340
Replacing the headlight bulb
If the headlight bulb burns out, replace it as follows.
1. Remove the panel shown by removing the
screws.2. Remove the headlight beam adjusting screw,
the washer, the spring and the nut.
NOTE:

Be sure not to lose the washer, the spring and the
nut.
1. Grease nipple
1

1. Panel
2. Screw
1 2 2

8-37
1
2
3
4
5
6
78
9
10
11

3. Disconnect the main switch leads.4. Remove the headlight unit from the headlight
assembly by removing the screws.
1. Headlight beam adjusting screw
2. Washer
3. Spring
4. Nut
1 2
3 4

1. Main switch lead
1

8-38
1
2
3
4
5
6
78
9
10
11

5. Remove the headlight bulb holder cover.
6. Remove the headlight bulb holder by turning it
counterclockwise, and then remove the defec-
tive bulb.
1. Headlight unit
2. Screw
1
21
2

1. Headlight bulb holder cover
2. Headlight bulb holder
1 2

8-39
1
2
3
4
5
6
78
9
10
11
WARNING

EWB02200
A headlight bulb is hot when it is on and imme-
diately after it is turned off. Wait for the bulb to
cool before touching or removing it. You can
be burned, or a fire could start if the bulb
touches something flammable.
7. Place a new bulb into position, and then install
the bulb holder by turning it clockwise.
CAUTION:

ECB00650
Do not touch the glass part of the headlight
bulb to keep it free from oil, otherwise the
transparency of the glass, the luminosity of the
bulb, and the bulb life will be adversely affect-
ed. Thoroughly clean off any dirt and finger-
prints on the headlight bulb using a cloth
moistened with alcohol or thinner.
8. Install the headlight bulb holder cover.
1. Headlight bulb holder
2. Headlight bulb
12

1. Do not touch the glass part of the bulb.1

8-40
1
2
3
4
5
6
78
9
10
11
CAUTION:

ECB00670
Make sure the headlight bulb holder cover is
securely fitted over the bulb holder and seated
properly.
9. Place the headlight unit in the original posi-
tion, and then install the screws.
10. Install the headlight beam adjusting screw,
the washer, the spring and the nut.11. Connect the main switch leads.
12. Install the panel by installing the screws.
13. Adjust the headlight beam.
EBU25550
Adjusting a headlight beam
CAUTION:

ECB00690
It is advisable to have a Yamaha dealer make
this adjustment.
1. Headlight unit
2. Screw
1
21
2

1. Headlight beam adjusting screw
2. Washer
3. Spring
4. Nut
1 2
3 4

8-41
1
2
3
4
5
6
78
9
10
11

To raise a headlight beam, turn the adjusting
screw in direction (a).
To lower a headlight beam, turn the adjusting
screw in direction (b).
EBU25610
Replacing the tail/brake light bulb
If the tail/brake light bulb burns out, replace it as
follows.
1. Remove the bulb holder (together with the
bulb) by turning it counterclockwise.2. Remove the defective bulb by pushing it in
and turning it counterclockwise.
1. Headlight beam adjusting screw
1(a)
(b)

1. Tail/brake light bulb holder
1

8-42
1
2
3
4
5
6
78
9
10
11

3. Insert a new bulb into the bulb holder, push it
in, and then turn it clockwise until it stops.
4. Install the bulb holder (together with the bulb)
by turning it clockwise.
EBU25650
Removing a wheel
1. Loosen the wheel nuts.
Front
1. Tail/brake light bulb holder
2. Tail/brake light bulb
1
2

1. Wheel nut
1
1

8-44
1
2
3
4
5
6
78
9
10
11
WARNING

EWB02280
Do not smoke when checking the fuel system.
Fuel can ignite or explode, causing severe inju-
ry or property damage. Make sure there are no
open flames or sparks in the area, including pi-
lot lights from water heaters or furnaces.

10-4
1
2
3
4
5
6
7
8
910
11
Electrical system:

Ignition system:
CDI
Charging system:
Flywheel magneto
Headlight:
Bulb type:
Halogen bulb
Bulb voltage, wattage x quantity:
Headlight:
12 V, 35.0/36.5 W
×
1
Tail/brake light:
12 V, 5.0/21.0 W
×
1
Oil level warning light:
12 V, 3.4 W
×
1

INDEX
A
Accessories and loading ................................................ 6-6
Air filter element, cleaning ............................................ 8-11
Autolube pump ............................................................. 8-11
B
Brake and clutch levers, checking and lubricating ....... 8-34
Brake and shift pedals, checking and lubricating ......... 8-34
Brake fluid, changing.................................................... 8-25
Brake fluid level, checking............................................ 8-24
Brake lever ..................................................................... 4-5
Brake lever free play, checking the front ...................... 8-25
Brake light switches ..................................................... 8-29
Brake pads, checking the front and rear ...................... 8-23
Brake pedal .................................................................... 4-5
Brake pedal position, checking .................................... 8-26
Brakes, front and rear .................................................... 5-4
C
Cables, checking and lubricating ................................. 8-33
Carburetor settings, changing ...................................... 8-16
Chassis fasteners........................................................... 5-8
Cleaning ......................................................................... 9-1
Clutch lever .................................................................... 4-5
Clutch lever free play, adjusting ................................... 8-29
D
Drive chain ..................................................................... 5-5
Drive chain, lubricating ................................................. 8-32Drive chain slack .......................................................... 8-30
E
Engine break-in .............................................................. 6-4
Engine, cold start ........................................................... 6-1
Engine idling speed ...................................................... 8-21
Engine, starting a warm ................................................. 6-2
Engine stop switch ......................................................... 4-3
F
Fuel ........................................................................ 4-8
,
5-4
Fuel cock ........................................................................ 4-9
Fuel tank cap.................................................................. 4-8
H
Handlebar switches ........................................................ 4-2
Headlight beam, adjusting............................................ 8-40
Headlight bulb, replacing.............................................. 8-36
I
Identification numbers .................................................. 11-1
Indicator light .................................................................. 4-2
Instruments, lights and switches .................................... 5-8
K
Key identification number ............................................. 11-1
Kickstarter ...................................................................... 4-7
L
Label locations ............................................................... 2-1
Light switch .................................................................... 4-3