wheel YAMAHA BLASTER 200 2007 Owner's Manual

8-43
1
2
3
4
5
6
78
9
10
11
Rear

2. Elevate the ATV and place a suitable stand
under the frame.
3. Remove the nuts from the wheel.
4. Remove the wheel.
EBU25660
Installing a wheel
1. Install the wheel and the nuts.
2. Lower the ATV to the ground.
3. Tighten the wheel nuts to the specified
torques.
EBU25720
Troubleshooting
Although Yamaha ATVs receive a thorough in-
spection before shipment from the factory, trouble
may occur during operation. Any problem in the fu-
el, compression, or ignition systems, for example,
can cause poor starting and loss of power.
The following troubleshooting chart represents a
quick and easy procedure for checking these vital
systems yourself. However, should your ATV re-
quire any repair, take it to a Yamaha dealer, whose
skilled technicians have the necessary tools, expe-
rience, and know-how to service the ATV properly.
Use only genuine Yamaha replacement parts. Im-
itation parts may look like Yamaha parts, but they
are often inferior, have a shorter service life and
can lead to expensive repair bills.
1. Wheel nut
1
1

Tightening torques:
Front wheel nut:
45 Nm (4.5 m·kgf, 32 ft·lbf)
Rear wheel nut:
45 Nm (4.5 m·kgf, 32 ft·lbf)

9-1
1
2
3
4
5
6
7
89
10
11

EBU25860
CLEANING AND STORAGE
EBU25900
Cleaning
Frequent, thorough cleaning of your ATV will not
only enhance its appearance but will improve its
general performance and extend the useful life of
many components.
1. Before cleaning the ATV:
a. Block off the end of the exhaust pipe to
prevent water entry. A plastic bag and
strong rubber band may be used.
b. Make sure the spark plug and all filler caps
are properly installed.
2. If the engine case is excessively greasy, apply
degreaser with a paint brush. Do not apply de-
greaser to the chain, sprockets or wheel ax-
les.
3. Rinse the dirt and degreaser off with a garden
hose. Use only enough pressure to do the job.
CAUTION:

ECB00710
Excessive water pressure may cause water
seepage and deterioration of wheel bearings,
brakes, transmission seals and electrical de-
vices. Many expensive repair bills have result-ed from improper high-pressure detergent
applications such as those available in coin-
operated car washers.
4. Once most of the dirt has been hosed off,
wash all surfaces with warm water and mild,
detergent-type soap. An old toothbrush or bot-
tle brush is handy for hard-to-reach places.
5. Rinse the ATV off immediately with clean wa-
ter and dry all surfaces with a chamois, clean
towel or soft absorbing cloth.
6. Dry the chain and lubricate it to prevent it from
rusting.
7. Clean the seat with a vinyl upholstery cleaner
to keep the cover pliable and glossy.
8. Automotive type wax may be applied to all
painted and chrome plated surfaces. Avoid
combination cleaner-waxes. Many contain
abrasives which may mar the paint or protec-
tive finish. When finished cleaning, start the
engine and let it idle for several minutes.

9-3
1
2
3
4
5
6
7
89
10
11

the next step.)
d. Turn the engine over several times with
the starter. (This will coat the cylinder wall
with oil.)
e. Remove the spark plug cap from the spark
plug, and then install the spark plug and
the spark plug cap.
6. Lubricate all control cables and the pivoting
points of all levers and pedals.
7. Check and, if necessary, correct the tire air
pressure, and then block up the ATV so that
all of its wheels are off the ground. Alternative-
ly, turn the wheels a little every month in order
to prevent the tires from becoming degraded
in one spot.
8. Cover the muffler outlet with a plastic bag to
prevent moisture from entering it.
NOTE:

Make any necessary repairs before storing the
ATV.

10-1
1
2
3
4
5
6
7
8
910
11

EBU25960
SPECIFICATIONS
EBU25975
Dimensions:
Overall length:
1735 mm (68.3 in)
Overall width:
1035 mm (40.7 in)
Overall height:
1040 mm (40.9 in)
Seat height:
740 mm (29.1 in)
Wheelbase:
1100 mm (43.3 in)
Ground clearance:
120 mm (4.7 in)
Minimum turning radius:
3000 mm (118 in)
Weight:
With oil and fuel:
155.0 kg (342 lb)
Engine:
Engine type:
Air cooled 2-stroke
Cylinder arrangement:
Forward-inclined single cylinder
Displacement:
195.0 cm
3

Bore
×
stroke:
66.0
×
57.0 mm (2.60
×
2.24 in)Compression ratio:
6.60 :1
Starting system:
Kickstarter
Lubrication system:
Separate lubrication (Yamaha autolube)
Type:
YAMALUBE 2-cycle oil or 2-stroke engine oil (AUS)(NZL)
YAMALUBE 2-cycle oil or 2-stroke engine oil (JASO FC
grade) (EUR)
Engine oil quantity:
Quantity:
1.3 L (1.37 US qt) (1.14 Imp.qt)

Transmission oil:
Type:
SAE10W30 type SE motor oil
Quantity:
0.6 L (0.69 US qt) (0.57 Imp.qt)
Air filter:
Air filter element:
Wet element
Fuel:
Recommended fuel:
Premium unleaded gasoline only
Fuel tank capacity:
9.0 L (2.38 US gal) (1.98 Imp.gal)
Fuel reserve amount:
2.0 L (0.53 US gal) (0.44 Imp.gal)

10-3
1
2
3
4
5
6
7
8
910
11

Manufacturer/model:
CHENG SHIN/C-874N
Loading:
Maximum loading limit:
100.0 kg (220 lb)
(Total weight of rider, cargo, accessories, and tongue)
Tire air pressure (measured on cold tires):
Recommended:
Front:
30.0 kPa (4.4 psi) (0.300 kgf/cm
2

)
Rear:
25.0 kPa (3.6 psi) (0.250 kgf/cm
2

)
Minimum:
Front:
27.0 kPa (3.9 psi) (0.270 kgf/cm
2

)
Rear:
22.0 kPa (3.2 psi) (0.220 kgf/cm
2

)
Maximum:
Front:
33.0 kPa (4.8 psi) (0.330 kgf/cm
2

)
Rear:
28.0 kPa (4.1 psi) (0.280 kgf/cm
2

)
Front wheel:
Wheel type:
Panel wheel
Rim size:
10 x 5.5AT
Rear wheel:
Wheel type:
Panel wheelRim size:
8 x 8.0AT
Front brake:
Type:
Dual disc brake
Operation:
Right hand operation
Recommended fluid:
DOT 4
Rear brake:
Type:
Single disc brake
Operation:
Right foot operation
Recommended fluid:
DOT 4
Front suspension:
Type:
Double wishbone
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
180 mm (7.1 in)
Rear suspension:
Type:
Swingarm (monocross)
Spring/shock absorber type:
Coil spring/gas-oil damper
Wheel travel:
180 mm (7.1 in)

10-4
1
2
3
4
5
6
7
8
910
11
Electrical system:

Ignition system:
CDI
Charging system:
Flywheel magneto
Headlight:
Bulb type:
Halogen bulb
Bulb voltage, wattage x quantity:
Headlight:
12 V, 35.0/36.5 W
×
1
Tail/brake light:
12 V, 5.0/21.0 W
×
1
Oil level warning light:
12 V, 3.4 W
×
1

M
Main switch .....................................................................4-1
Model label....................................................................11-2
O
Owner’s manual and tool kit............................................8-1
P
Parking ............................................................................6-5
Parking brake ..................................................................4-6
Parking brake free play, adjusting.................................8-27
Parking on a slope ..........................................................6-6
Part locations ..................................................................3-1
Periodic maintenance and lubrication chart ....................8-3
Pre-operation check list ..................................................5-1
R
Riding your ATV ..............................................................7-1
S
Safety information ...........................................................1-1
Seat...............................................................................4-11
Shifting ............................................................................6-2
Shift pedal .......................................................................4-7
Shock absorber assemblies, adjusting the front ...........4-12
Shock absorber assembly, adjusting the rear ...............4-13
Spark arrester, cleaning ................................................8-14
Spark plug, checking.......................................................8-7
Specifications ................................................................10-1
Speed limiter ...................................................................4-4
Starter (choke) ..............................................................4-11
Steering shaft, lubricating .............................................8-35
Storage ...........................................................................9-2
Suspension, lubricating the upper and lower arm
pivots ..........................................................................8-35Swingarm pivots, lubricating ........................................ 8-34
T
Tail/brake light bulb, replacing ..................................... 8-41
Throttle cable free play, adjusting ................................ 8-22
Throttle lever ...........................................................4-3
,
5-5
Throttle OverRide System.............................................. 4-4
Tire pressure, measuring ............................................... 5-7
Tires ............................................................................... 5-6
Tire wear limit................................................................. 5-8
Transmission oil ......................................................5-4
,
8-8
Troubleshooting ........................................................... 8-43
Troubleshooting chart .................................................. 8-45
Two-stroke engine oil ..................................................... 5-4
Two-stroke engine oil level warning light ....................... 4-2
V
Vehicle identification number ....................................... 11-1
W
Wheel bearings, checking ............................................ 8-34
Wheel, installing ........................................................... 8-43
Wheel, removing .......................................................... 8-42