clock YAMAHA CYGNUS 125 2012 Owners Manual

1
2
3
4
5
6
7
8
9
3-3
EAU1044E
INSTRUMENT AND CONTROL FUNCTIONS
engine is not working correctly. If this
occurs, have a Yamaha dealer check
the self-diagnosis system.
The electrical circuit of the warning
light can be checked by turning the
key to “ON”. The warning light should
come on for a few seconds, and then
go off.
If the warning light does not come
on initially when the key is turned to
“ON”, or if the warning light remains
on, have a Yamaha dealer check the
electrical circuit.
EAU11601
SpeedometerZAUM00**
RESET
SELECT
1
1. SpeedometerThe speedometer shows the riding
speed.
When the key is turned to “ON”, the
speedometer needle will sweep once
across the speed range and then re-
turn to zero in order to test the electri-
cal circuit.
EAUT1957
Multi-function display
EWA14431
WARNING
Be sure to stop the vehicle before
making any setting changes to the
multi-function display. Changing
settings while riding can distract
the operator and increase the risk
of an accident.ZAUM00**
RESET
SELECT
1
2
3
4
5
6
1. Oil change indicator “7”
2. Odometer
3. Fuel meter
4. “RESET” button
5. “SELECT” button
6. ClockThe multi-function display is equipped
with the following:●
an odometer
4P9-F8199-E5_CS.indd 3-34P9-F8199-E5_CS.indd 3-3
2011/09/06 14:18:392011/09/06 14:18:39
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
3-4
EAU1044E
INSTRUMENT AND CONTROL FUNCTIONS●
a tripmeter (which shows the dis-
tance traveled since it was last
set to zero)
●
an oil change tripmeter (which
shows the distance traveled since
the last engine oil change)
●
an oil change indicator (which
flashes when the engine oil
should be changed)
●
a clock
●
a fuel meter
TIP●
When the key is turned to “ON”,
all segments of the display come
on for a few seconds. During this
time, the multi-function display is
performing a self-test.
●
Be sure to turn the key to “ON”
before using the “SELECT” and
“RESET” buttons.
Odometer, tripmeter and oil change
tripmeter modes
Pushing the “SELECT” button switch-
es the display among the odom-
eter mode “ODO”, the tripmeter mode
“TRIP” and the oil change tripmeter
“OIL CHANGE TRIP” in the following
order:
ODO → TRIP → OIL CHANGE TRIP
→ ODO
OdometerTIPIf the odometer indicates “-----”, have
a Yamaha dealer check the multi-
function display, as it may be faulty.
Tripmeter
To reset the tripmeter, select it by
pushing the “SELECT” button until
“TRIP” is displayed, and then push the
“RESET” button at least 1 second.TIPIf the tripmeter indicates “-----”, have
a Yamaha dealer check the multi-
function display, as it may be faulty.
Oil change tripmeter
To reset the oil change tripmeter, se-
lect it by pushing the “SELECT” but-
ton until “OIL CHANGE TRIP” is dis-
played, and then push the “RESET”
button at least 3 seconds.
Push the “SELECT” button again to
start the oil change tripmeter; the dis-
play changes to the ODO mode.
Oil change indicator “7”
This indicator flashes at the initial
1000 km (600 mi), then at every 3000
km (1800 mi) thereafter to indicate
that the engine oil should be changed.
After changing the engine oil, reset
the oil change tripmeter.
If the engine oil is changed before
the oil change indicator flashes (i.e.
before the periodic oil change interval
has been reached), the oil change
tripmeter must be reset after the
oil change for the next periodic oil
change to be indicated at the correct
time.TIP●
If the oil change tripmeter is reset
before the initial 1000 km (600
mi), the next periodic oil change
4P9-F8199-E5_CS.indd 3-44P9-F8199-E5_CS.indd 3-4
2011/09/06 14:18:392011/09/06 14:18:39
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
3-5
EAU1044E
INSTRUMENT AND CONTROL FUNCTIONS
interval will be at every 3000 km
(1800 mi) thereafter.
●
If the oil change tripmeter in-
dicates “-----”, have a Yamaha
dealer check the multi-function
display, as it may be faulty.
Clock
To set the clock:
1. Push the “SELECT” button and
“RESET” button together for at
least two seconds.
2. When the hour digits start flash-
ing, push the “SELECT” button to
set the hours.
3. Push the “RESET” button, and
the first minute digit will start
fl ashing.
4. Push the “SELECT” button to set
the fi rst minute digit.
5. Push the “RESET” button and
the second minute digit will start
fl ashing.
6. Push the “SELECT” button to set
the second minute digit.
7. Push the “RESET” button and
then release it to start the clock.Fuel meter
The fuel meter indicates the amount
of fuel in the fuel tank. The display
segments of the fuel meter disappear
towards “E” (Empty) as the fuel level
decreases. When “
” starts flashing,
refuel as soon as possible. When the
key is turned to “ON”, all of the display
segments of the fuel meter will appear
for a few seconds, and then shown
actual fuel level.
EAU12349
Handlebar switchesLeftZAUM00**
3 1
2
1. Dimmer switch “%/&”
2. Turn signal switch “4/6”
3. Horn switch “*”RightZAUM00**
1
1. Start switch “,”
4P9-F8199-E5_CS.indd 3-54P9-F8199-E5_CS.indd 3-5
2011/09/06 14:18:392011/09/06 14:18:39
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
3-7
EAU1044E
INSTRUMENT AND CONTROL FUNCTIONS
EAU13074
Fuel tank capTo open the fuel tank cap
Open the fuel tank cap lock cover,
insert the key into the lock, and then
turn it 1/4 turn clockwise. The lock will
be released and the fuel tank cap can
be opened.ZAUM00**
1
1. Fuel tank cap lock coverTo close the fuel tank cap
1. Push the fuel tank cap into posi-
tion with the key inserted in the
lock.
2. Turn the key counterclockwise to
the original position, remove it,
and then close the lock cover.
TIPThe fuel tank cap cannot be closed
unless the key is in the lock. In addi-
tion, the key cannot be removed if the
cap is not properly closed and locked.
EWA11091
WARNING
Make sure that the fuel tank cap
is properly closed after lling fuel.
Leaking fuel is a re hazard.
EAU13221
FuelZAUM00**
1
2
1. Fuel tank fi ller tube
2. Fuel levelMake sure there is suffi cient gasoline
in the tank.
EWA10881
WARNING
Gasoline and gasoline vapors are
extremely ammable. To avoid res
and explosions and to reduce the
risk of injury when refueling, follow
these instructions.
1. Before refueling, turn off the en-
gine and be sure that no one is
sitting on the vehicle. Never re-
fuel while smoking, or while in the
4P9-F8199-E5_CS.indd 3-74P9-F8199-E5_CS.indd 3-7
2011/09/06 14:18:392011/09/06 14:18:39
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
3-10
EAU1044E
INSTRUMENT AND CONTROL FUNCTIONS
EAUT1503
SeatTo open the seat
1. Place the scooter on the center-
stand.
2. Insert the key into the main
switch, and then turn it coun-
terclockwise to the first “OPEN”
position. If the main switch is in
the “LOCK” position, turn the key
counterclockwise to the second
“OPEN” position.ZAUM00**TIPDo not push inward when turning the
key from “OFF” to “OPEN” or from
“LOCK” to “OPEN”.
3. Fold the seat up.
To close the seat
1. Fold the seat down, and then
push it down to lock it in place.
2. Remove the key from the main
switch if the scooter will be left
unattended.TIPMake sure that the seat is properly se-
cured before riding.
EAUT1713
Storage compartmentsFront storage compartmentZAUM00**
1
1. Front storage compartment
EWA11191
WARNING
● Do not exceed the load limit of
1.5 kg (3.3 lb) for the front stor-
age compartment.● Do not exceed the maximum
load of 157 kg (346 lb) for the
vehicle.
4P9-F8199-E5_CS.indd 3-104P9-F8199-E5_CS.indd 3-10
2011/09/06 14:18:402011/09/06 14:18:40
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-28
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
EAUT1892
Replacing a front turn signal
light bulb
ECA10670
NOTICEIt is advisable to have a Yamaha
dealer perform this job.
1. Place the scooter on the center-
stand.
2. Remove panel A. (See page 6-7.)
3. Remove the socket (together with
the bulb) by turning it counter-
clockwise.
4. Remove the burnt out bulb by
pushing it in and turning it coun-
terclockwise.ZAUM00**
1
2
1. Turn signal light bulb
2. Socket
5. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
6. Install the socket (together with
the bulb) by turning it clockwise.
7. Install the panel.
EAUT1923
Replacing the tail/brake light
bulb or a rear turn signal light
bulbZAUM00**3
1
2
4
1. Tail/brake light lens
2. Turn signal light lens
3. Rear turn signal light bulb
4. Tail/brake light bulbTail/brake light bulb
1. Remove the tail/brake light lens
by removing the screws.
2. Remove the burnt out bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.
4P9-F8199-E5_CS.indd 6-284P9-F8199-E5_CS.indd 6-28
2011/09/06 14:18:412011/09/06 14:18:41
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-29
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENTRear turn signal light bulb
1. Remove the tail/brake light lens
by removing the screws.
2. Remove the turn signal light lens
by removing the screws.
3. Remove the burnt out bulb by
pushing it in and turning it coun-
terclockwise.
4. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
5. Install the turn signal light lens by
installing the screws.
6. Install the tail/brake light lens
by installing the screws.
NO-
TICE:
Do not overtighten the
screws, otherwise the lens may
break.[ECA10681]EAUT1963
Replacing an auxiliary light
bulbZAUM00**
12
1. Auxiliary light bulb
2. SocketThis model is equipped with two aux-
iliary lights. If an auxiliary light bulb
burns out, replace it as follows.
1. Remove panel B. (See page 6-7.)
2. Remove the auxiliary light socket
(together with the bulb) by turning
it counterclockwise.
3. Remove the burnt out bulb by
pulling it out.
4. Insert a new bulb into the socket.
5. Install the auxiliary light socket
(together with the bulb) by turning
it clockwise.
6. Install the panel.
EAU25861
TroubleshootingAlthough Yamaha scooters receive a
thorough inspection before shipment
from the factory, trouble may occur
during operation. Any problem in the
fuel, compression, or ignition systems,
for example, can cause poor starting
and loss of power.
The following troubleshooting chart
represents a quick and easy pro-
cedure for checking these vital sys-
tems yourself. However, should your
scooter require any repair, take it to a
Yamaha dealer, whose skilled techni-
cians have the necessary tools, expe-
rience, and know-how to service the
scooter properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
EWA15141
WARNING
When checking the fuel system, do
not smoke, and make sure there
are no open flames or sparks in
4P9-F8199-E5_CS.indd 6-294P9-F8199-E5_CS.indd 6-29
2011/09/06 14:18:412011/09/06 14:18:41
Process BlackProcess Black