engine overheat YAMAHA FX 2003 Owners Manual

2-15
E
EJU19940
Yamaha Engine Management
System (YEMS)
This model is equipped with an inte-
grated, computerized management system
that controls and adjusts ignition timing, fuel
injection, engine diagnostics, and the Off-
Throttle Steering (OTS) system.
EJU01786
Multifunction meter
This meter contains the following func-
tions for help and convenience in operating
the watercraft.
1
Tachometer
2
Hour meter/Voltmeter
3
Speedometer
4
Fuel meter
5
Fuel warning indicator
6
Engine overheat warning indicator
7
Speedometer display select switch
8
Hour meter/Voltmeter display select switch
9
Check engine warning indicator
0
Oil pressure warning indicator
CAUTION:@ Do not run the engine for more than
15 seconds when checking the operation
of the meter on land. The engine could
overheat.
NOTE:@
When the engine is started, all displays
light up for 2 seconds and the buzzer
sounds 2 times. Then, the meter starts to
operate normally.

The current display will continue to oper-
ate for 25 seconds after the engine stops.
UF1B71.book Page 15 Tuesday, November 12, 2002 4:17 PM

2-19
E
EJU01794
Engine overheat warning indicator
This model is equipped with an engine
overheat warning system.
If the engine starts to overheat, the over-
heat warning indicator blinks for 5 seconds,
and then it comes on. The buzzer also
begins to sound intermittently, and then it
sounds continuously. At the same time, the
engine speed reduction control is activated
when the engine runs over 3,000 r/min.
If this occurs, immediately reduce the
engine speed and beach the watercraft, and
check for water discharge at the port (left)
cooling water pilot outlet. If there is no dis-
charge of water, check the intake grate and
impeller for clogging.
WARNING@ Before attempting to remove weeds or
debris from the intake grate or impeller,
shut the engine off and remove the clip
from the engine shut-off switch. Severe
injury or death could result from coming
in contact with the rotating parts of the
jet pump.
CAUTION:@ If you cannot locate and correct the
cause of the overheating, consult a
Yamaha dealer. Continuing to operate at
higher speeds could result in severe
engine damage.
NOTE:@ Press any button on the multifunction meter
to stop the buzzer.
UF1B71.book Page 19 Tuesday, November 12, 2002 4:17 PM

3-14
E
EJU01058
Jet unit
Carefully check the jet intake for weeds,
debris, or anything else that might restrict
the intake of water. If the intake is clogged,
cavitation could occur, reducing jet thrust,
and possibly damaging the jet pump.
In some cases, the engine may overheat
because of lack of cooling water, and dam-
age to the engine could result. Engine cool-
ing water is fed to the engine by the jet
pump. (See page 5-3 for jet intake cleaning
procedures.)
WARNING@
Keep away from intake grate while
engine is on. Items such as long hair,
loose clothing, or PFD straps can
become entangled in moving parts
resulting in severe injury or drowning.

Stop the engine and remove the clip
from the engine shut-off switch before
removing any debris or weeds, which
may have collected around the jet
intake.
EJU01059
Engine shut-off cord (lanyard)
Check that the engine shut-off cord is not
frayed or broken. If the cord is damaged,
replace it; never try to repair it or tie it
together.
UF1B71.book Page 14 Tuesday, November 12, 2002 4:17 PM

3-34
E
EJU01866
Post-operation checks
Always perform the following post-opera-
tion checks after operating the watercraft.
1. Remove the watercraft from the water.
2. Wash down the hull, handlebars, and jet
unit with fresh water.
3. Remove the seat and check the engine
compartment for water. To drain excess
water, remove the stern drain plugs, and
then raise the bow of the watercraft
enough to allow water in the bilge to
drain out.
NOTE:@ This watercraft is equipped with a jet vac-
uum bilge draining system and an electric
bilge draining system that remove water
from the engine compartment while you are
underway. However, some residual water will
remain. (See “Bilge” on page 3-9 for more
information.)
4. Put the watercraft in a horizontal posi-
tion.
5. Flush the cooling system to prevent it
from clogging with salt, sand, or dirt.
(See page 4-1 for flushing procedures.)
6. Drain residual water from the exhaust
system by alternately squeezing and
releasing the throttle lever for 10 to
15 seconds while the engine is running.
CAUTION:@ Do not run the engine for more than
15 seconds on land. The engine could
overheat.
UF1B71.book Page 34 Tuesday, November 12, 2002 4:17 PM

4-1
E
EJU18121
Storage
WARNING@ Always place the watercraft upright in a
horizontal position when storing it, oth-
erwise fuel could leak out into the engine
or engine compartment, which could
result in a fire hazard.
@
Storage for prolonged periods of time,
such as winter storage, requires preventa-
tive maintenance to ensure against deterio-
ration. It is advisable to have the watercraft
serviced by a Yamaha dealer prior to stor-
age. However, the following procedures can
be performed by the owner.
EJU01813
Flushing the cooling system
Flushing the cooling system is essential
to prevent the cooling system from being
clogged with salt, sand, or dirt.
CAUTION:@
Do not supply water to the cooling
water passages when the engine is not
running. The water could flow back
through the muffler into the crankcase
causing severe engine damage.

Do not run the engine for more 15 sec-
onds without supplying water, other-
wise the engine may overheat.
E_F1B-70-4.fm Page 1 Tuesday, November 19, 2002 3:21 PM

4-3
E
EJU01898
Lubrication
WARNING@ Do not spray flammable rust inhibitor
products on engine surfaces while the
engine is hot. The sprayed substance or
propellants could catch fire.
@
1. Remove the rear and front seats. (See
pages 2-5 to 2-6 for seat removal and
installation procedures.)
2. Remove the air filter case cover
screws1, slide the locks 2 open, and
then remove the case cover.
3. Remove the air filter case cover and air
filter element.
4. Spray a rust inhibitor into each intake
opening 3 for 3 seconds.
5. Install the air filter element and air filter
case cover.
6. Start the engine in a well-ventilated area
and let it run at idle for 15 seconds.
CAUTION:@ Do not run the engine for more than
15 seconds. The engine could overheat.
@
7. Lubricate all cables such as the throttle
and steering cables.
NOTE:@ Use a suitable marine grease applicator to
pressure lubricate the cables and purge out
any moisture between the inner and outer
cables.
@
8. Lubricate the areas of the watercraft
specified under Lubrication points on
page 4-18.
UF1B71.book Page 3 Tuesday, November 12, 2002 4:17 PM

5-3
E
EJU01118
Emergency procedures
EJU01119
Cleaning the jet intake and
impeller
If weeds or debris get caught in the intake
or impeller, cavitation can occur, causing jet
thrust to decrease even though engine
speed rises. If this condition is allowed to
continue, the engine will overheat and may
seize. If there is any sign that the jet intake
or impeller is clogged with weeds or debris,
beach the watercraft and check the intake
and impeller. Always stop the engine before
beaching the watercraft.
WARNING@ Before attempting to remove weeds or
debris from the jet intake or impeller
areas, shut the engine off and remove
the clip from the engine shut-off switch.
Severe injury or death could result from
contact with the rotating parts of the jet
pump.
1. Turn the watercraft on its side as shown.
CAUTION:@
Place a suitable clean cloth or carpet-
ing underneath the watercraft to pro-
tect it from abrasions and scratches.

Always turn the watercraft over onto
its port (left) side.

When turning the watercraft on its
side, support the bow so the handle-
bars cannot be bent or damaged.
UF1B71.book Page 3 Tuesday, November 12, 2002 4:17 PM

6-1
E
EJU01125
Index
A
Adjusting the fuel injection system ........ 4-23
Approval label of Emission control
certificate ................................................. 1-3
B
Battery ............................................ 3-10, 4-5
Beaching the watercraft ........................ 3-32
Bilge ........................................................ 3-9
Boarding alone ...................................... 3-25
Boarding and starting in deep water ..... 3-25
Boarding with passengers ..................... 3-26
Bow down.............................................. 2-14
Bow up .................................................. 2-14
C
Capsized watercraft .............................. 3-27
Changing the engine oil ........................ 4-11
Check engine warning indicator ............ 2-17
Checking the air filter element............... 4-13
Checking the trolling speed ................... 4-23
Cleaning and adjusting the
spark plugs ............................................ 4-16
Cleaning the jet intake and impeller ........ 5-3
Cleaning the watercraft ........................... 4-6
Connecting the jumper cables................. 5-6
Cooling water pilot outlet ................ 2-9, 3-15
Cruising limitations ................................ 1-12
D
Docking the watercraft .......................... 3-32
E
Emergency procedures ........................... 5-3
Emission control information
(For Canada only) ................................... 1-3
Engine break-in ..................................... 3-16
Engine compartment ............................... 3-6
Engine oil ................................................ 3-3
Engine oil level ........................................ 3-7
Engine overheat warning indicator ........ 2-19
Engine serial number .............................. 1-2
Engine shut-off cord (lanyard) ............... 3-14
Engine shut-off switch ............................. 2-8Engine stop switch .................................. 2-7
Enjoy your watercraft responsibly ......... 1-19
F
Filling the fuel tank .................................. 3-4
Fire extinguisher .................................... 3-11
Flushing the cooling system .................... 4-1
Front seat ................................................ 2-6
Front storage compartment ................... 2-20
Fuel and oil.............................................. 3-1
Fuel level ................................................. 3-6
Fuel meter ............................................. 2-16
Fuel system ............................................. 4-4
Fuel tank ............................................... 4-10
Fuel tank filler cap ................................... 2-7
Fuel warning indicator ........................... 2-18
G
Gasohol ................................................... 3-2
Gasoline .................................................. 3-1
Getting to know your watercraft ............ 3-21
Glove compartment ............................... 2-21
H
Handgrip ................................................ 2-14
Hazard information ................................ 1-16
Hood........................................................ 2-7
Hour meter/Voltmeter ............................ 2-17
Hull Identification Number (HIN).............. 1-2
I
Identification numbers ............................. 1-1
Important labels ....................................... 1-4
Inspecting and adjusting the
throttle cable.......................................... 4-14
Inspecting the battery ............................ 4-21
Inspecting the fuel system ..................... 4-10
Inspecting the jet thrust nozzle angle .... 4-14
Inspecting the QSTS mechanism .......... 4-15
Inspecting the shift cable ....................... 4-14
J
Jet unit................................................... 3-14
Jumping the battery ................................. 5-5
UF1B71.book Page 1 Tuesday, November 12, 2002 4:17 PM