battery YAMAHA FZR SVHO 2009 User Guide

Maintenance and care
71
*1 This operation should be performed after every use.
*2 This operation should be performed before long-term storage.
BatteryCheck, charge 76
Rubber couplingCheck—
Engine mountCheck—
Nuts and boltsCheck—
Air filter elementCheck 72
Engine oilReplace
50 hours or 12 months72
Oil filterReplace 72
Valve clearanceCheck, adjust— Item OperationInitial Thereafter every
Page 10
hours50
hours100
hours100
hours200
hours
6
months12
months12
months24
months
UF2R70E0.book Page 71 Thursday, November 6, 2008 10:05 AM

Maintenance and care
76

Throttle cable (handlebar end)

Steering cable (handlebar end)

Steering cable (jet thrust nozzle end)

QSTS rod (jet thrust nozzle end)

Shift cable (reverse gate end)

Intermediate housing
Fill the intermediate housing with water-re-
sistant grease through the grease nipple
using a grease gun.
EJU34452Checking the battery
Check the level of the battery electrolyte and
make sure that the negative (–) and positive
(+) battery leads are tightened securely.
Grease quantity:
Initial 10 hours or 1 month:
33.0–35.0 cm³ (1.12–1.18 US oz,
1.16–1.23 Imp.oz)
Every 100 hours or 12 months:
6.0–8.0 cm³ (0.20–0.27 US oz,
0.21–0.28 Imp.oz)
1Grease nipple
1
UF2R70E0.book Page 76 Thursday, November 6, 2008 10:05 AM

Maintenance and care
77
WARNING
EWJ00791
Battery electrolyte is poisonous and dan-
gerous, causing severe burns, etc. Elec-
trolyte contains sulfuric acid. Avoid
contact with skin, eyes, or clothing.
Antidotes
External: Flush with water.
Internal: Drink large quantities of water or
milk. Follow with milk of magnesia, beaten
egg, or vegetable oil. Call a physician im-
mediately.
Eyes: Flush with water for 15 minutes and
get prompt medical attention.
Batteries produce explosive gases. Keep
sparks, flames, cigarettes, etc., well away.
If using or charging the battery in an en-
closed space, make sure that it is well ven-
tilated. Always shield your eyes when
working near batteries.
Keep out of the reach of children.
To remove the battery:
Disconnect the negative (–) battery lead first,
then the positive (+) battery lead and breather
hose, and then remove the battery from the
watercraft.To replenish the battery:
(1) Make sure that the electrolyte level is be-
tween the maximum and minimum level
marks.
(2) If the electrolyte level is low, add distilled
water to raise it to the specified level.
NOTICE: Use only distilled water for
replenishing the battery, otherwise
battery life could be shortened.
[ECJ00241]
To recharge the battery:
NOTICE
ECJ00250
Do not attempt to charge a battery hastily.
Battery life could be shortened.
It is recommended to have a Yamaha dealer
charge the battery. If you charge the battery
yourself, be sure to read and follow the in-
structions provided with the battery tester and
charger you use.
To install the battery:
(1) Place the battery in the battery compart-
ment. Connect the red lead to the positive
(+) battery terminal, and then connect the
black lead to the negative (–) battery ter-
minal. NOTICE: Reversal of the battery
leads will damage the electrical parts.
[ECJ00261]
(2) Connect the breather hose to the battery.
1Maximum level mark
2Minimum level mark
UF2R70E0.book Page 77 Thursday, November 6, 2008 10:05 AM

Maintenance and care
78
(3) Secure the battery in place. WARNING!
Fire or explosion could result if the
breather hose is damaged, obstruct-
ed, or not connected properly.
[EWJ00451]
EJU34491
Fuel injection system
If the fuel injection system is malfunctioning,
have a Yamaha dealer service the watercraft.
EJU37500Checking the trolling speed
(1) Place the watercraft in the water.
(2) Start the engine and warm it up. Use the
tachometer in the dual analog meter unit
to check the trolling speed.
If the trolling speed is out of specification,
have a Yamaha dealer service the watercraft.
1Negative (–) battery terminal: Black lead
2Positive (+) battery terminal: Red lead
3Breather hose
Trolling speed:
1250 ±100 r/min
12
3
UF2R70E0.book Page 78 Thursday, November 6, 2008 10:05 AM

Specifications
79
EJU34542
Specifications
Watercraft capacity:
Maximum people on board:
2 person
Maximum load capacity:
160 kg (353 lb)
Dimensions:
Length:
3350 mm (131.9 in)
Width:
1230 mm (48.4 in)
Height:
1160 mm (45.7 in)
Dry weight:
366 kg (807 lb)
Performance:
Maximum output (according to ISO 8665/SAE
J1228):
154.50 kW@7500 r/min
Maximum fuel consumption:
67.3 L/h (17.8 US gal/h, 14.8 Imp.gal/h)
Cruising range at full throttle:
1.04 hour
Trolling speed:
1250 ±100 r/min
Engine:
Engine type:
Liquid cooled 4-stroke, DOHC
Number of cylinders:
4
Engine displacement:
1812 cm³
Bore & stroke:
86.0 × 78.0 mm (3.39 × 3.07 in)
Compression ratio:
8.6 : 1
Valve clearance-intake (cold):
0.14–0.23 mm (0.0055–0.0091 in)
Valve clearance-exhaust (cold):
0.28–0.37 mm (0.0110–0.0146 in)
Lubrication system:
Wet sump
Cooling system:
Water
Starting system:
Electric
Ignition system:
T.C.I.Spark plug:
LFR6A
Spark plug gap:
0.8–0.9 mm (0.031–0.035 in)
Battery capacity:
12 V, 19.0 Ah
Charging system:
Flywheel magneto
Drive unit:
Propulsion system:
Jet pump
Jet pump type:
Axial flow, single stage
Impeller rotation:
Counterclockwise
Jet thrust nozzle angle:
24.0+24.0 °
Jet thrust nozzle trim angle:
-10, -5, 0, 5, 10 °
Fuel and oil:
Recommended fuel:
Regular unleaded gasoline
Minimum octane rating (PON):
86
Minimum octane rating (RON):
90
Recommended engine oil type SAE:
SAE 10W-30, 10W-40, 20W-40, 20W-50
Recommended engine oil grade API:
API SE,SF,SG,SH,SJ,SL
Fuel tank total capacity:
70 L (18.5 US gal, 15.4 Imp.gal)
Engine oil quantity with oil filter replacement:
3.1 L (3.28 US qt, 2.73 Imp.qt)
Engine oil quantity without oil filter replacement:
3.0 L (3.17 US qt, 2.64 Imp.qt)
Engine oil total quantity:
4.3 L (4.55 US qt, 3.78 Imp.qt)
UF2R70E0.book Page 79 Thursday, November 6, 2008 10:05 AM

Trouble recovery
80
EJU34560
Troubleshooting
If you have any trouble with your watercraft, use this section to check for the possible cause.
If you cannot find the cause, or if the procedure for replacement or repair is not described in
this owner’s/operator’s manual, have a Yamaha dealer perform the necessary service.
EJU36982Troubleshooting chart
TROUBLE POSSIBLE CAUSE REMEDY PAGE
Engine does not
start (Starter motor
does not turn over)Yamaha Se-
curity SystemLock mode selected Select unlock mode
31
Engine shut-
off switchClip not in place Install clip
25
Fuse Burned out Replace fuse and
check wiring84
Battery Run down Recharge 76
Poor terminal con-
nectionsTighten as required
76
Terminal corroded Clean 68
Starter motor Faulty Have serviced by
Yamaha dealer—
Engine does not
start (Starter motor
turns over)Throttle lever Squeezed Release 26
Fuel Empty Refill as soon as pos-
sible41
Stale or contaminat-
edHave serviced by
Yamaha dealer72
Fuel tank Water or dirt present Have serviced by
Yamaha dealer72
Spark plug Fouled or defective Clean or replace 74
Spark plug
capNot connected or
looseConnect properly
74
Connected to wrong
cylinderConnect properly
74
Fuel injec-
tion systemFuel pump faulty Have serviced by
Yamaha dealer—
UF2R70E0.book Page 80 Thursday, November 6, 2008 10:05 AM

Trouble recovery
84
(2) Remove any weeds or debris from
around the jet intake, drive shaft, impel-
ler, jet pump housing, and jet thrust noz-
zle.
If debris is difficult to remove, consult a
Yamaha dealer.
EJU34641Jumping the battery
If the watercraft battery has run down, the en-
gine can be started using a 12-volt booster
battery and jumper cables.
EJU34662Connecting the jumper cables
WARNING
EWJ01250
To avoid battery explosion and serious
damage to the electrical system:

Do not reverse the polarity of the jumper
cables when connecting to the batteries.

Do not connect the negative (–) jumper
cable to the negative (–) terminal of the
watercraft battery.

Do not touch the positive (+) jumper ca-
ble to the negative (–) jumper cable.
(1) Connect the positive (+) jumper cable to
the positive (+) battery terminals of both
batteries.
(2) Connect one end of the negative (–)
jumper cable to the negative (–) battery
terminal of the booster battery.(3) Connect the other end of the negative (–)
jumper cable to an engine hanger.
(4) Start the engine, and then disconnect the
jumper cables by reversing the steps
above. NOTICE: Never push the start
switch while the engine is running. Do
not operate the start switch for more
than 5 seconds, otherwise the battery
will be discharged and the engine will
not start. Also, the starter motor could
be damaged. If the engine does not
start in 5 seconds, release the start
switch, wait 15 seconds, and then try
again.
[ECJ00481]
EJU36991
Replacing the fuses
The fuses are located in the electrical box.
To replace a fuse:
(1) Remove the seats. (See page 23 for seat
removal and installation procedures.)
1Negative (–) jumper cable
2Positive (+) jumper cable
3Booster battery
4Engine hanger
2
3 1
4
UF2R70E0.book Page 84 Thursday, November 6, 2008 10:05 AM

Trouble recovery
85
(2) Remove the electrical box cover.
(3) Remove the cap on the electrical box.
(4) Replace the blown fuse with the spare
fuse of the correct amperage by using the
fuse puller on the reverse side of the cap.
WARNING! Do not use fuses of higher
amperage than recommended. Substi-
tution with a fuse that has an improper
rating can cause extensive electricalsystem damage and possible fire.
[EWJ00801]
(5) Install the cap.
(6) Install the electrical box cover.
(7) Install the seats.
1Electrical box cover
1
1Electrical box
2Spare fuse
3Fuse
4Cap
1Fuse puller
Fuse amperage:
Battery fuse:
30 A
Main relay drive fuse:
10 A
Electronic throttle valve fuse:
10 A
Security system fuse:
3 A
Main fuse:
20 A
3 2
4
1
UF2R70E0.book Page 85 Thursday, November 6, 2008 10:05 AM

Index
A
Air filter element ....................................... 72
B
Battery ................................................ 47, 68
Battery, checking...................................... 76
Battery, jumping ....................................... 84
Beaching the watercraft ........................... 64
Bilge ......................................................... 47
Boarding alone ......................................... 58
Boarding and starting from a dock ........... 58
Boarding and starting in deep water ........ 58
Boarding and starting in shallow water .... 57
Boarding with a passenger....................... 59
Bow down................................................. 30
Bow eye ................................................... 30
Bow up ..................................................... 30
Builder’s plate............................................. 2
C
Capsized watercraft ................................. 61
Check engine warning.............................. 37
Cleaning the watercraft ............................ 68
Cooling water pilot outlets .................. 27, 52
Craft Identification Number (CIN) ............... 1
Cruising limitations ................................... 11
D
Docking the watercraft ............................. 64
Dual analog meter unit ....................... 33, 52
E
Emergency procedures ............................ 83
Engine break-in ........................................ 53
Engine compartment ................................ 45
Engine oil ................................................. 42
Engine oil and oil filter .............................. 72
Engine oil level ......................................... 45
Engine overheat warning ......................... 36
Engine serial number ................................. 1
Engine shut-off cord (lanyard) .................. 51
Engine shut-off switch .............................. 25
Engine stop switch ................................... 25
Enjoy your watercraft responsibly ............ 17
F
Fire extinguisher....................................... 48
Flushing the cooling system ..................... 67
Front storage compartment ...................... 37
Fuel .......................................................... 41Fuel and oil............................................... 41
Fuel injection system ................................ 78
Fuel level .................................................. 45
Fuel level meter ........................................ 35
Fuel level warning .................................... 35
Fuel system, checking .............................. 72
Fuel tank .................................................. 72
Fuel tank filler cap .................................... 24
Fuses, replacing ....................................... 84
G
Getting to know your watercraft ............... 56
Glove compartment .................................. 38
H
Hazard information ................................... 15
Hood ......................................................... 24
Hour meter/voltmeter ............................... 34
Hull and deck ........................................... 45
I
Identification numbers ................................ 1
Information display ................................... 34
J
Jet intake .................................................. 51
Jet intake and impeller, cleaning .............. 83
Jet thrust nozzle angle, checking ............. 72
Jumper cables, connecting ...................... 84
L
Labels, important ........................................ 3
Labels, other .............................................. 8
Labels, warning .......................................... 4
Launching the watercraft .......................... 53
Learning to operate your watercraft ......... 56
Leaving the watercraft .............................. 55
Limitations on who may operate the
watercraft .............................................. 10
L-MODE (low-RPM mode) ....................... 32
Lubrication................................................ 68
Lubrication points ..................................... 75
M
Main components, location of .................. 19
Maintenance and adjustments ................. 69
Model information....................................... 2
O
Oil pressure warning ................................ 35
Operating in weeded areas ...................... 64
Operating your watercraft ......................... 56
UF2R70E0.book Page 1 Thursday, November 6, 2008 10:05 AM