8-34
1
2
3
4
5
6
78
9
10
11
the hub stopper bolt.
3. Loosen the axle holding bolts.
4. Loosen the chain adjusting bolt locknut. To
tighten the drive chain, turn the adjusting bolt
in direction (a). To loosen the drive chain, turn
the adjusting bolt in direction (b), and then
push the wheels forward.
NOTICE:
Improper
drive chain slack will overload the engine
as well as other vital parts of the ATV and
can lead to drive chain slippage or break-age. To prevent this from occurring, keep
the drive chain slack within the specified
limits.
[ECB00542]
5. Tighten the locknut and the axle holding bolts
to the specified torques.
1. Hub stopper bolt
2. Locknut
3. Axle holding bolt (lower)
4. Axle holding bolt (upper)
1
2
34
1. Locknut
2. Drive chain slack adjusting bolt
1
2
(a)
(b)
8-35
1
2
3
4
5
6
78
9
10
11
NOTICE
ECB00550
If measurement “A” of the drive chain adjust-
ing bolt is less than 27 mm (1.06 in), have a
Yamaha dealer replace the drive chain.
6. Tighten the hub stopper bolt, and then its lock-
nut.
EBU24882
Lubricating the drive chain
The drive chain must be cleaned and lubricated at
the intervals specified in the periodic maintenance
and lubrication chart, otherwise it will quickly wear
out, especially when riding in dusty or wet areas.
Service the drive chain as follows.NOTICE
ECB00561
The drive chain must be lubricated after wash-
ing the ATV or riding in the rain or wet areas.
1. Clean the drive chain with kerosene and a
small soft brush.
NOTICE:
To prevent dam-
aging the O-rings, do not clean the drive
chain with steam cleaners, high-pressure
washers or inappropriate solvents.
[ECB00571]
Tightening torques:
Chain adjusting bolt locknut:
16 Nm (1.6 m·kgf, 12 ft·lbf)
Axle holding bolt (upper):
85 Nm (8.5 m·kgf, 61 ft·lbf)
Axle holding bolt (lower):
60 Nm (6.0 m·kgf, 43 ft·lbf)
1. Measurement A
1
8-48
1
2
3
4
5
6
78
9
10
11
TIP
Tapered nuts are used for both the front and rear
wheels. Install the nuts with their tapered side to-
wards the wheel.
4. Lower the ATV to the ground.
5. Tighten the wheel nuts to the specified
torques.
EBU25720
Troubleshooting
Although Yamaha ATVs receive a thorough in-
spection before shipment from the factory, trouble
may occur during operation. Any problem in the fu-
el, compression, or ignition systems, for example,
can cause poor starting and loss of power.
The following troubleshooting chart represents a
quick and easy procedure for checking these vital
systems yourself. However, should your ATV re-
quire any repair, take it to a Yamaha dealer, whose
skilled technicians have the necessary tools, expe-
rience, and know-how to service the ATV properly.
Use only genuine Yamaha replacement parts. Im-
itation parts may look like Yamaha parts, but they
are often inferior, have a shorter service life and
can lead to expensive repair bills.
1. Tapered nut
1
Tightening torques:
Front wheel nut:
55 Nm (5.5 m·kgf, 40 ft·lbf)
Rear wheel nut:
55 Nm (5.5 m·kgf, 40 ft·lbf)
