light YAMAHA GRIZZLY 125 2012 Owner's Manual

8-44
8
EBU25263Replacing the fuse The fuse holder is located on the right side of the
ATV.
If the fuse is blown, replace it as follows.
1. Turn the key to “OFF” and turn off all electrical
circuits.
NOTICEECB00640To prevent accidental short-circuiting, turn off
the main switch when checking or replacing a
fuse.2. Remove the blown fuse, and then install a
new fuse of the specified amperage.
WARNING! Always use a fuse of the spec-
ified rating, and never use a substitute ob-
ject in place of the proper fuse. An
improper fuse or a substitute object can
cause damage to the electrical system,
which could lead to a fire.
[EWB02172]
3. Turn the key to “ON” and turn on the electrical
circuits to check if the devices operate.
4. If the fuse immediately blows again, have a
Yamaha dealer check the electrical system.EBU25481Replacing a headlight bulb If a headlight bulb burns out, replace it as follows.
1. Fuse
2. Spare fuse
12
Specified fuse:
15.0 A
U1PY60E0.book Page 44 Friday, March 11, 2011 9:30 AM

8-45
81. Remove the cover at the rear of the headlight
by pulling it off.
2. Remove the headlight bulb holder cover by
pulling it off.3. Remove the headlight bulb holder by pushing
it in and turning it counterclockwise.
4. Remove the burnt-out bulb by pulling it out.
5. Insert a new headlight bulb into the bulb hold-
er by pushing it in. NOTICE: Do not touch
the glass part of the headlight bulb to keep
it free from oil, otherwise the transparency
of the glass, the luminosity of the bulb, and
the bulb life will be adversely affected.
Thoroughly clean off any dirt and finger-
prints on the headlight bulb using a cloth
moistened with alcohol or thinner.
[ECB00651]
1. Cover at the rear of the headlight
1
1. Headlight bulb holder cover
2. Headlight bulb holder
12
U1PY60E0.book Page 45 Friday, March 11, 2011 9:30 AM

8-46
8 6. Install the bulb holder by pushing it in and turn-
ing it clockwise.
7. Install the bulb holder cover and the cover at
the rear of the headlight. NOTICE: Make sure
the headlight bulb holder cover is securely
fitted over the bulb holder and seated
properly.
[ECB00671]
8. Adjust the headlight beam if necessary.
EBU25551Adjusting a headlight beam NOTICEECB00690It is advisable to have a Yamaha dealer make
this adjustment.To raise a headlight beam, turn the headlight beam
adjusting screw in direction (a).
To lower a headlight beam, turn the adjusting
screw in direction (b).
1. Headlight bulb
1
1. Headlight beam adjusting screw
1(a)
(b)
U1PY60E0.book Page 46 Friday, March 11, 2011 9:30 AM

8-47
8
EBU25613Replacing the tail/brake light bulb If the tail/brake light bulb burns out, replace it as
follows.
1. Remove the tail/brake light bulb holder (to-
gether with the bulb) by turning it counter-
clockwise.
2. Remove the burnt-out bulb by pushing it in
and turning it counterclockwise.
3. Insert a new bulb into the bulb holder, push it
in, and then turn it clockwise until it stops.4. Install the bulb holder (together with the bulb)
by turning it clockwise.
EBU25651Removing a wheel 1. Place the ATV on a level surface.
2. Loosen the wheel nuts.
1. Tail/brake light bulb holder
1
1. Tail/brake light bulb
2. Tail/brake light bulb holder
12
U1PY60E0.book Page 47 Friday, March 11, 2011 9:30 AM

8-49
8
EBU25720Troubleshooting Although Yamaha ATVs receive a thorough in-
spection before shipment from the factory, trouble
may occur during operation. Any problem in the fu-
el, compression, or ignition systems, for example,
can cause poor starting and loss of power.
The following troubleshooting chart represents a
quick and easy procedure for checking these vital
systems yourself. However, should your ATV re-
quire any repair, take it to a Yamaha dealer, whose
skilled technicians have the necessary tools, expe-
rience, and know-how to service the ATV properly.
Use only genuine Yamaha replacement parts. Im-
itation parts may look like Yamaha parts, but they
are often inferior, have a shorter service life and
can lead to expensive repair bills.
WARNING
EWB02280Do not smoke when checking the fuel system.
Fuel can ignite or explode, causing severe inju-
ry or property damage. Make sure there are no
open flames or sparks in the area, including pi-
lot lights from water heaters or furnaces.
Tightening torques:
Front wheel nut:
55 Nm (5.5 m·kgf, 40 ft·lbf)
Rear wheel nut:
55 Nm (5.5 m·kgf, 40 ft·lbf)
U1PY60E0.book Page 49 Friday, March 11, 2011 9:30 AM

10-4
10
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
70 mm (2.8 in)Rear suspension:Type:
Swingarm
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
80 mm (3.1 in)Electrical system:Ignition system:
DC CDI
Charging system:
AC magnetoBattery:Model:
12N12C-4A-2
Voltage, capacity:
12 V, 12.0 AhHeadlight:Bulb type:
Krypton bulbBulb voltage, wattage × quantity:Headlight:
12 V, 30.0/30.0 W × 2
Tail/brake light:
12 V, 5.0/21.0 W × 1
Neutral indicator light:
12 V, 1.7 W × 1Reverse indicator light:
12 V, 1.7 W × 1
Fuses:Main fuse:
15.0 AEBU30400For EUR only
The figures quoted are emission levels and are not
necessarily safe working levels. Whilst there is a
correlation between the emission and exposure
levels, this cannot be used reliably to determine
whether or not further precautions are required.
Factors that influence the actual level of exposure
of work-force include the characteristics of the
work room, the other sources of noise, etc. i.e. the
number of machines and other adjacent process-
es, and the length of time for which an operator is
exposed to the noise. Also the permissible expo-
sure level can vary from country. This information,
however, will enable the user of the machine to
make a better evaluation of the hazard and risk.
U1PY60E0.book Page 4 Friday, March 11, 2011 9:30 AM

INDEX
AAccessories and loading ................................................ 6-6
Air filter elements, engine and V-belt filter cleaning ..... 8-17BBattery ................................................................... 5-6, 8-41
Brake lever free play, adjusting the front ..................... 8-28
Brake lever free play (rear), adjusting .......................... 8-32
Brake lever, front ............................................................ 4-4
Brake lever, rear ............................................................ 4-5
Brake levers, checking and lubricating ........................ 8-38
Brakes .......................................................................... 8-27
Brakes, front and rear .................................................... 5-3
Brake shoes, checking the front and rear .................... 8-27CCables, checking and lubricating ................................. 8-37
Carburetor, adjusting ................................................... 8-25
Carrier, front ................................................................. 4-11
Carrier, rear .................................................................. 4-11
Chassis fasteners .......................................................... 5-6
Cleaning ......................................................................... 9-1DDrive chain ..................................................................... 5-3
Drive chain, lubricating ................................................. 8-36
Drive chain slack .......................................................... 8-34
Drive select lever ........................................................... 4-6
Drive select lever and driving in reverse ........................ 6-3EEngine break-in .............................................................. 6-4Engine, cold start ........................................................... 6-1
Engine idling speed ..................................................... 8-25
Engine oil .............................................................. 5-3, 8-11
Engine, starting a warm ................................................. 6-2
Engine stop switch ......................................................... 4-2
FFront knuckle pivots, lubricating .................................. 8-40
Fuel ......................................................................... 4-7, 5-3
Fuel cock ....................................................................... 4-8
Fuel tank cap ................................................................. 4-7
Fuse, replacing ............................................................ 8-44HHandlebar switches ....................................................... 4-2
Headlight beam, adjusting ........................................... 8-46
Headlight bulb, replacing ............................................. 8-44
Horn switch .................................................................... 4-3IIdentification numbers .................................................. 11-1
Indicator lights ................................................................ 4-2
Instruments, lights and switches .................................... 5-6LLabel locations ............................................................... 1-1
Light switch .................................................................... 4-3MMain switch .................................................................... 4-1
Maintenance and lubrication chart ................................. 8-5
Maintenance chart, emission control system ................. 8-3
Model label .................................................................. 11-2
U1PY60E0.book Page 1 Friday, March 11, 2011 9:30 AM

NNeutral indicator light ..................................................... 4-2OOwner’s manual and tool kit ........................................... 8-2PParking ........................................................................... 6-5
Parking brake ................................................................. 4-5
Parking on a slope ......................................................... 6-5
Part locations ................................................................. 3-1RReverse indicator light .................................................... 4-2
Riding your ATV ............................................................. 7-1SSafety information .......................................................... 2-1
Seat .............................................................................. 4-10
Spark arrester, cleaning ............................................... 8-23
Spark plug, checking ...................................................... 8-9
Specifications ............................................................... 10-1
Speed limiter .................................................................. 4-4
Starter (choke) ............................................................. 4-10
Start switch ..................................................................... 4-3
Steering shaft, lubricating ............................................. 8-40
Storage ........................................................................... 9-2
Suspension, lubricating the lower arm pivots ............... 8-39TTail/brake light bulb, replacing ..................................... 8-47
Throttle lever ........................................................... 4-3, 5-3
Throttle lever free play, adjusting ................................. 8-26
Tires ............................................................................... 5-3
Transmission oil .................................................... 5-3, 8-14
Troubleshooting ........................................................... 8-49
Troubleshooting chart .................................................. 8-50
VValve clearance ............................................................ 8-27
V-belt case drain screw ................................................ 8-24
Vehicle identification number ....................................... 11-1WWheel hub bearings, checking ..................................... 8-38
Wheel, installing ........................................................... 8-48
Wheel, removing .......................................................... 8-47
U1PY60E0.book Page 2 Friday, March 11, 2011 9:30 AM