engine oil YAMAHA JOG50R 2007 User Guide

EAUS1090
Cleaning the air filter
element
The air filter element should be clea-
ned at the intervals specified in the
periodic maintenance and lubrication
chart. Clean the air filter element more
frequently if you are riding in unu-
sually wet or dusty areas.
1. Lid from the air filter box
2. Screw
3. Screw
1. Remove the screw clamp and the
screws that fasten the air filter
case to the crankcase.
1. Lid from the air filter box
2. Screws (x 3)
2. Remove the air filter case cover
by removing the screws.
3. Pull the air filter element out.
4. Clean the air filter element with
solvent, and then squeeze the
remaining solvent out.
1. The air filter
EWA10430
s s
WARNING
Use only a dedicated parts clea-
ning solvent. To avoid the risk of
fire or explosion, do not use gasoli-
ne or solvents with a low flash
point.
ECA10510
CAUTION
To avoid damaging the foam mate-
rial, handle it gently and carefully,
and do not twist or wring it.
5. Apply oil of the recommended
type to the entire surface of the
sponge material, and then sque-
eze the excess oil out.
NOTE:
The air filter element should be wet
but not dripping.
6. Insert the element into the air fil-
ter case.
Recommended oil:
Engine oil
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-8
12
3
1 2
1
5RW-F8199-E3.qxd 08/09/2005 18:07 Página 35

and the cables and cable ends should
be lubricated if necessary. If a cable is
damaged or does not move smoothly,
have a Yamaha dealer check or repla-
ce it.
EWA10720
s s
WARNING
Damage to the outer sheath may
interfere with proper cable opera-
tion and will cause the inner cable
to rust. Replace a damaged cable
as soon as possible to prevent
unsafe conditions.
EAU23110
Checking and lubricating the
throttle grip and cable
The operation of the throttle grip
should be checked before each ride.
In addition, the cable should be lubri-
cated or replaced at the intervals spe-
cified in the periodic maintenance
chart.
EAU23120
Adjusting the Autolube pump
The Autolube pump is a vital and sop-
histicated component of the engine,
which must be adjusted by a Yamaha
dealer at the intervals specified in the
periodic maintenance and lubrication
chart.
EAU23170
Lubricating the front and
rear brake levers
The pivoting points of the front and
rear brake levers must be lubricated
at the intervals specified in the perio-
dic maintenance and lubrication
chart.
EAU23190
Checking and lubricating the
centerstand
The operation of the centerstand
should be checked before each ride,
and the pivots and metal-to-metal
contact surfaces should be lubricated
if necessary.
EWA11300
s s
WARNING
If the centerstand does not move
up and down smoothly, have a
Yamaha dealer check or repair it.
Recommended lubricant:
Lithium-soap-based grease (all-
purpose grease)
Recommended lubricant:
Lithium-soap-based grease (all-
purpose grease)
Recommended lubricant:
Engine oil
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-14
5RW-F8199-E3.qxd 08/09/2005 18:07 Página 41

EAU23271
Checking the front fork
The condition and operation of the
front fork must be checked as follows
at the intervals specified in the perio-
dic maintenance and lubrication chart.
To check the condition
EWA10750
s s
WARNING
Securely support the motorcycle so
that there is no danger of it falling
over.
Check the inner tubes for scratches,
damage and excessive oil leakage.
To check the operation
1. Place the motorcycle on a level
surface and hold it in an upright
position.2. While applying the front brake,
push down hard on the handle-
bars several times to check if the
front fork compresses and
rebounds smoothly.
ECA10590
CAUTION
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or
repair it.
EAU23280
Checking the steering
Worn or loose steering bearings may
cause danger. Therefore, the opera-
tion of the steering must be checked
as follows at the intervals specified in
the periodic maintenance and lubrica-
tion chart.1. Place a stand under the engine to
raise the front wheel off the
ground.
EWA10750
s s
WARNING
Securely support the motorcycle so
that there is no danger of it falling
over.
2. Hold the lower ends of the front
fork legs and try to move them
forward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the stee-
ring.
EAU23290
Checking the wheel bearings
The front and rear wheel bearings
must be checked at the intervals spe-
cified in the periodic maintenance and
lubrication chart. If there is play in the
wheel hub or if the wheel does not
turn smoothly, have a Yamaha dealer
check the wheel bearings.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-15
5RW-F8199-E3.qxd 08/09/2005 18:07 Página 42

EAU26090
Care
While the open design of a scooter
reveals the attractiveness of the tech-
nology, it also makes it more vulnera-
ble. Rust and corrosion can develop
even if high-quality components are
used. A rusty exhaust pipe may go
unnoticed on a car, however, it
detracts from the overall appearance
of a scooter. Frequent and proper
care does not only comply with the
terms of the warranty, but it will also
keep your scooter looking good,
extend its life and optimize its perfor-
mance.
Before cleaning
1. Cover the muffler outlet with a
plastic bag after the engine has
cooled down.
2. Make sure that all caps and
covers as well as all electrical
couplers and connectors, inclu-
ding the spark plug cap, are
tightly installed.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such pro-ducts onto seals, gaskets and
wheel axles. Always rinse the dirt
and degreaser off with water.
Cleaning
ECA10780
CAUTION
Avoid using strong acidic whe-
el cleaners, especially on spo-
ked wheels. If such products
are used on hard-to-remove
dirt, do not leave the cleaner on
the affected area any longer
than instructed. Also, tho-
roughly rinse the area off with
water, immediately dry it, and
then apply a corrosion protec-
tion spray.
Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or spon-
ge with mild detergent and
water to clean plastic.
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent orthinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
Do not use high-pressure was-
hers or steam-jet cleaners sin-
ce they cause water seepage
and deterioration in the follo-
wing areas: seals (of wheel and
swingarm bearings, fork and
brakes), electric components
(couplers, connectors, instru-
ments, switches and lights),
breather hoses and vents.
For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or scrat-
ching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not lea-
ve any marks. If the windshield
is scratched, use a quality
plastic polishing compound
after washing.
7
SCOOTER CARE AND STORAGE
7-1
5RW-F8199-E3.qxd 08/09/2005 18:07 Página 48

After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottle-
brush for hard-to-reach areas. Stub-
born dirt and insects will come off
more easily if the area is covered with
a wet cloth for a few minutes before
cleaning.
After riding in the rain, near the sea or
on salt-sprayed roads
Since sea salt or salt sprayed on the
roads during winter are extremely
corrosive in combination with water,
carry out the following steps after
each ride in the rain, near the sea or
on salt-sprayed roads.
NOTE:
Salt sprayed on roads in the winter
may remain well into spring.
1. Clean the scooter with cold water
and a mild detergent after the
engine has cooled down.
ECA10790
CAUTION
Do not use warm water since it
increases the corrosive action of
the salt.
2. Apply a corrosion protection
spray on all metal, including
chrome- and nickel-plated, surfa-
ces to prevent corrosion.
After cleaning
1. Dry the scooter with a chamois or
an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally indu-
ced discoloring of stainless-steel
exhaust systems can be removed
through polishing.)
3. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal, inclu-
ding chrome- and nickel-plated,
surfaces.
4. Use spray oil as a universal clea-
ner to remove any remaining dirt.
5. Touch up minor paint damage
caused by stones, etc.6. Wax all painted surfaces.
7. Let the scooter dry completely
before storing or covering it.
EWA10940
s s
WARNING
Make sure that there is no oil or
wax on the brakes or tires. If
necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or
acetone, and wash the tires
with warm water and a mild
detergent.
Before operating the scooter
test its braking performance
and cornering behavior.
ECA10800
CAUTION
Apply spray oil and wax spa-
ringly and make sure to wipe
off any excess.
Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.
Avoid using abrasive polishing
compounds as they will wear
away the paint.
7
SCOOTER CARE AND STORAGE
7-2
5RW-F8199-E3.qxd 08/09/2005 18:07 Página 49

NOTE:
Consult a Yamaha dealer for advice
on what products to use.
EAU26300
Storage
Short-term
Always store your scooter in a cool,
dry place and, if necessary, protect it
against dust with a porous cover.
ECA10820
CAUTION
Storing the scooter in a poorly
ventilated room or covering it
with a tarp, while it is still wet,
will allow water and humidity to
seep in and cause rust.
To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-
cals are stored.
Long-term
Before storing your scooter for seve-
ral months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. Drain the carburetor float cham-ber by loosening the drain bolt;
this will prevent fuel deposits
from building up. Pour the drai-
ned fuel into the fuel tank.
3. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
4. Perform the following steps to
protect the cylinder, piston rings,
etc. from corrosion.
a. Remove the spark plug cap and
spark plug.
b. Pour a teaspoonful of engine oil
into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit sparking
during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap from
the spark plug, and then install
the spark plug and the spark plug
cap.
EWA10950
s s
WARNING
To prevent damage or injury from
sparking, make sure to ground the
spark plug electrodes while turning
the engine over.
5. Lubricate all control cables and
the pivoting points of all levers
and pedals as well as of the
sidestand/centerstand.
6. Check and, if necessary, correct
the tire air pressure, and then lift
the scooter so that both of its
wheels are off the ground. Alter-
natively, turn the wheels a little
every month in order to prevent
the tires from becoming degra-
ded in one spot.
7. Cover the muffler outlet with a
plastic bag to prevent moisture
from entering it.
8. Remove the battery and fully
charge it. Store it in a cool, dry
place and charge it once a
month. Do not store the battery in
an excessively cold or warm pla-
ce [less than 0 °C (30 °F) or more
than 30 °C (90 °F)]. For more
7
SCOOTER CARE AND STORAGE
7-3
5RW-F8199-E3.qxd 08/09/2005 18:07 Página 50

DimensionsOverall length
1740 mm
Overall width
675 mm
Overall height
1065 mm
Seat height
770 mm
Wheelbase
1210 mm
Ground clearance
132 mm
WeightWith oil and fuel
CS50 80.5 kg
CS50Z 83.7 kg
EngineEngine type
CS50 Air cooled 2-stroke
CS50Z Liquid cooled 2-stroke
Cylinder arrangement
Forward-inclined single cylinder
Displacement
49.2 cm3
Bore x stroke
40.0 x 39.2 mm
Compression ratio
CS50 10.20 :1
CS50Z 11.40 :1
Starting system
Electric starter and kickstarter
Lubrication system
Separate lubrication (Yamaha autolube)Type
YAMALUBE 2-cycle oil or 2-stroke engine
oil
Engine oil quantityQuantity
1.4 L
Transmission oilType
YAMALUBE 4 (10W30) or SAE10W30
type SE motor oil
Oil change quantity
0.10 L
Air filter element
Wet element
Fuel
Recommended fuel
Regular unleaded gasoline
Fuel tank capacity
5.5 L
CarburetorManufacturer
CS50 DELLORTO GURTNER
CS50Z DELLORTO
Type x quantity
CS50 PHVA 12 ZS/1 PY 12/1
CS50Z PHVA 12 ZS/1
Spark plug(s)Manufacturer/model
NGK/BR8HS
Spark plug gap
0.6-0.7 mm
Clutch type
Dry, centrifugal automatic
TransmissionPrimary reduction system
Helical gear
Primary reduction ratio
52/13 (4.000)
Secondary reduction system
Spur gear
Secondary reduction ratio
CS50 42/13 (3.230)
CS50Z 43 x 13 (3.310)
Transmission type
Single speed automatic
Operation
Centrifugal automatic type
ChassisCaster angle
25.00 degree
Trail
80.0 mm
Front tireSize
110/70-12 47L
Rear tireSize
120/70-12 51L 130/70-12 56L
Maximum load
CS50 161 kg
CS50Z 158 kg
Tire air pressure (measured on cold
tires)
Front
175 kPa
Rear
200 kPa
8
SPECIFICATIONS
8-1
5RW-F8199-E3.qxd 08/09/2005 18:07 Página 52

22-stroke engine oil .....................................3-5
AAcceleration and deceleration ...................5-2
Adjusting the Autolube pump ..................6-14
Adjusting the brake lever free play ..........6-11
Adjusting the carburetor ............................6-9
Adjusting the rear brake lever free play ...6-11
Adjusting the throttle cable free play .........6-9
BBattery......................................................6-17
Braking .......................................................5-2
CCare............................................................7-1
Changing the brake fluid..........................6-13
Checking and lubricating the cables .......6-13
Checking and lubricating the
centerstand ............................................6-14
Checking and lubricating the throttle
grip and cable ........................................6-14
Checking the front brake fluid level .........6-13
Checking the front brake pads and rear
brake shoes ...........................................6-12
Checking the front fork ............................6-15
Checking the spark plug ............................6-5
Checking the steering ..............................6-15
Checking the wheel bearings ..................6-15
Cleaning the air filter element ....................6-8
Clock ..........................................................3-3
Controls and instruments ..........................2-3
Coolant (only for liquid-cooled models).....6-6
EEngine break-in ..........................................5-2
FFinal transmission oil .................................6-6
Front brake lever ........................................3-4
Fuel ............................................................3-5
Fuel and 2-stroke engine oil tank caps .....3-4
Fuel gauge .................................................3-3
HHandlebar switches ...................................3-3
IIdentification numbers ...............................9-1
Indicator lights ...........................................3-1
KKickstarter ..................................................3-6
LLeft view .....................................................2-1
Lubricating the front and rear brake
levers .....................................................6-14
MMain switch/steering lock ..........................3-1
PParking .......................................................5-2
Periodic maintenance and lubrication
chart .........................................................6-2
Pre-operation check list .............................4-2
RRear brake lever .........................................3-4
Replacing a turn signal light bulb or the
tail/brake light bulb ................................6-16
Replacing the fuse ...................................6-18
Replacing the headlight bulb or a front
turn signal light bulb ..............................6-16
Replacing the license plate light bulb......6-17
Right view ..................................................2-2
SSeat ............................................................3-6
Speedometer unit ......................................3-2
Starting a cold engine ................................5-1
Starting off .................................................5-1
Storage.......................................................7-3
Storage compartment ................................3-6
TTires ...........................................................6-9
Troubleshooting .......................................6-19
Troubleshooting chart ..............................6-20
INDEX
5RW-F8199-E3.qxd 08/09/2005 18:07 Página 55