light YAMAHA KODIAK 700 2016 Owner's Guide

8-49
8
EBU34270Brake light switchesThe brake light, which is activated by the brake
pedal and brake levers, should come on just be-
fore braking takes effect.
The rear brake light switch can be adjusted as fol-
lows, but the front brake light switch should be ad-
justed by a Yamaha dealer.
Turn the rear brake light switch adjusting nut while
holding the brake light switch in place. To make
the brake light come on earlier, turn the adjusting
nut in direction (a). To make the brake light come
on later, turn the adjusting nut in direction (b).
EBU24905Checking and lubricating the cablesThe operation and the condition of all control ca-
bles should be checked before each ride, and the
cables and cable ends should be lubricated if nec-
essary. If a cable is damaged or does not move
smoothly, have a Yamaha dealer check or replace
it.
1. Rear axle boot (each side)
1
1
1. Rear brake light switch adjusting nut
2. Rear brake light switchRecommended lubricant:
Yamaha cable lubricant or other suitable cable lubricant
1
2 (b)
(a)
UB1660E0.book Page 49 Thursday, February 26, 2015 4:01 PM

8-58
8The main fuse, the fuel injection system fuse, the
EPS fuse, and the fuse box are located under pan-
el A. (See page 8-10.)
If a fuse is blown, replace it as follows.1. Turn the key to “ ” (off) and turn off all elec- trical circuits.
NOTICEECB00641To prevent accidental short-circuiting, turn off
the main switch when checking or replacing a
fuse. 2. Remove the blown fuse, and then install anew fuse of the specified amperage.
WARNING! Always use a fuse of the spec-
ified rating, and never use a substitute ob-
ject in place of the proper fuse. An
improper fuse or a substitute object can
cause damage to the electrical system,
which could lead to a fire.
[EWB02173]
1. Headlight fuse
2. Signaling system fuse
3. Radiator fan motor fuse
4. Ignition fuse
5. Four-wheel-drive motor fuse (YFM70KPSG)
6. Auxiliary DC jack fuse
7. Spare fuse
8. Spare fuse (YFM70KPXG / YFM70KPHG / YFM70KPSG)
123456
87
UB1660E0.book Page 58 Thursday, February 26, 2015 4:01 PM

8-59
8
3. Turn the key to “ ” (on) and turn on the elec- trical circuits to check if the devices operate. 4. If the fuse immediately blows again, have a
Yamaha dealer check the electrical system.
EBU34220Replacing a headlight bulbIf a headlight bulb burns out, replace it as follows.
Left and right headlight bulbs1. Remove the cover at the rear of the headlight by pulling it off.
2. Remove the headlight bulb holder cover by pulling it off.
Specified fuses:
Main fuse:40.0 A
Headlight fuse: 10.0 A (YFM70KDHG, YFM70KDXG)
15.0 A (YFM70KPHG, YFM70KPSG,
YFM70KPXG)
Ignition fuse: 10.0 A
Four-wheel-drive motor fuse: 10.0 A (YFM70KPSG)
Signaling system fuse: 10.0 A
Auxiliary DC jack fuse: 10.0 A
Radiator fan motor fuse: 20.0 A
Fuel injection system fuse: 15.0 A
EPS fuse: 40.0 A (YFM70KPHG, YFM70KPSG,
YFM70KPXG)1. Cover at the rear of the headlight
1
UB1660E0.book Page 59 Thursday, February 26, 2015 4:01 PM

8-60
83. Remove the headlight bulb holder by pushing
it in and turning it counterclockwise. 4. Remove the burnt-out bulb by pulling it out.
5. Place a new headlight bulb into position.
NOTICE: Do not touch the glass part of the
headlight bulb to keep it free from oil, oth-
erwise the transparency of the glass, the
luminosity of the bulb, and the bulb life will
be adversely affected. Thoroughly clean
off any dirt and fingerprints on the head-
light bulb using a cloth moistened with al-
cohol or thinner.
[ECB00652]
6. Install the bulb holder by pushing it in and turning it clockwise.
1. Headlight bulb holder cover
1. Headlight bulb holder
1
1
1. Do not touch the glass part of the bulb.
UB1660E0.book Page 60 Thursday, February 26, 2015 4:01 PM

8-61
8
7. Install the bulb holder cover and the cover at
the rear of the headlight. NOTICE: Make
sure the headlight bulb holder cover is se-
curely fitted over the bulb holder and seat-
ed properly.
[ECB00672]
8. Adjust the headlight beam if necessary.
Center headlight bulb (YFM70KPXG /
YFM70KPHG / YFM70KPSG) 1. Remove the headlight cover by removing the quick fasteners.
2. Remove the headlight bulb holder cover by pulling it off. 3. Remove the headlight bulb holder by pushing
it in and turning it counterclockwise.1. Headlight cover
2. Quick fastener
1
2
2
1. Headlight bulb holder cover
1. Headlight bulb holder
1
1
UB1660E0.book Page 61 Thursday, February 26, 2015 4:01 PM

8-62
84. Remove the burnt-out bulb by pulling it out.
5. Place a new headlight bulb into position.
NOTICE: Do not touch the glass part of the
headlight bulb to keep it free from oil, oth-
erwise the transparency of the glass, the
luminosity of the bulb, and the bulb life will
be adversely affected. Thoroughly clean
off any dirt and fingerprints on the head-
light bulb using a cloth moistened with al-
cohol or thinner.
[ECB00652]
6. Install the bulb holder by pushing it in and turning it clockwise. 7. Install the bulb holder cover.
NOTICE: Make
sure the headlight bulb holder cover is se-
curely fitted over the bulb holder and seat-
ed properly.
[ECB00672]
8. Install the headlight cover as shown, and then install the quick fasteners.
9. Adjust the headlight beam if necessary.EBU25553Adjusting a headlight beamNOTICEECB00691It is advisable to have a Yamaha dealer make
this adjustment.
1. Do not touch the glass part of the bulb.
1. Headlight cover
1
UB1660E0.book Page 62 Thursday, February 26, 2015 4:01 PM

8-63
8
To raise a headlight beam, turn the headlight
beam adjusting screw in direction (a).
To lower a headlight beam, turn the adjusting
screw in direction (b).
YFM70KPXG / YFM70KPHG / YFM70KPSG
EBU25614Replacing the tail/brake light bulbIf the tail/brake light bulb burns out, replace it as
follows.
1. Remove the tail/brake light bulb holder (to- gether with the bulb) by turning it counter-
clockwise.
1. Headlight beam adjusting screw
(b)
(a)
1
1. Headlight beam adjusting screw
(b)
(a)
1
UB1660E0.book Page 63 Thursday, February 26, 2015 4:01 PM

8-64
82. Remove the burnt-out bulb by pushing it in
and turning it counterclockwise. 3. Insert a new bulb into the bulb holder, push it
in, and then turn it clockwise until it stops.
4. Install the bulb holder (together with the bulb) by turning it clockwise.
EBU25652Removing a wheel1. Place the ATV on a level surface.
2. Loosen the wheel nuts.
3. Elevate the ATV and place a suitable standunder the frame.
4. Remove the nuts from the wheel.
5. Remove the wheel.
1. Tail/brake light bulb holder
1. Tail/brake light bulb
1
1
1. Wheel nut
1
1
UB1660E0.book Page 64 Thursday, February 26, 2015 4:01 PM

8-66
8
EBU25741TroubleshootingAlthough Yamaha ATVs receive a thorough in-
spection before shipment from the factory, trouble
may occur during operation. Any problem in the
fuel, compression, or ignition systems, for exam-
ple, can cause poor starting and loss of power.
The following troubleshooting charts represent
quick and easy procedures for checking these vi-
tal systems yourself. However, should your ATV
require any repair, take it to a Yamaha dealer,
whose skilled technicians have the necessary
tools, experience, and know-how to service the
ATV properly.
Use only genuine Yamaha replacement parts. Im-
itation parts may look like Yamaha parts, but they
are often inferior, have a shorter service life and
can lead to expensive repair bills.
WARNING
EWB02281Do not smoke when checking the fuel system.
Fuel can ignite or explode, causing severe inju-
ry or property damage. Make sure there are no
open flames or sparks in the area, including pi-
lot lights from water heaters or furnaces. UB1660E0.book Page 66 Thursday, February 26, 2015 4:01 PM

10-4
10
Rear wheel:Wheel type:Cast wheel (YFM70KPSG)
Panel wheel (YFM70KDHG, YFM70KDXG,
YFM70KPHG, YFM70KPXG)
Rim size: 12 x 7.5ATFront brake:Type:
Disc brake
Operation: Right hand operation
Specified brake fluid: DOT 4Rear brake:Type:Wet multiple disc brake
Operation: Left hand and right foot operationFront suspension:Type:Double wishbone
Spring/shock absorber type: Coil spring/oil damper
Wheel travel:
193 mm (7.6 in)Rear suspension:Type:Double wishbone
Spring/shock absorber type:
Coil spring/oil damper Wheel travel:
232 mm (9.1 in)
Electrical system:Ignition system:
TCI
Charging system: AC magnetoBattery:Model:
YTX20L-BS
Voltage, capacity: 12 V, 18.0 AhHeadlight:Bulb type:
Krypton bulb
High-mounted headlight bulb type: Halogen bulb (YFM70KPHG, YFM70KPSG,
YFM70KPXG)Bulb voltage, wattage × quantity:Headlight:
12 V, 30.0/30.0 W × 2
High-mounted headlight:
12 V, 35.0/36.5 W × 1 (YFM70KPHG, YFM70KPSG,
YFM70KPXG)
Tail/brake light:
12 V, 5.0/21.0 W × 1
Meter lighting: EL (Electroluminescent) (YFM70KPHG, YFM70KPSG,
YFM70KPXG)
Neutral indicator light: LED
UB1660E0.book Page 4 Thursday, February 26, 2015 4:01 PM