light YAMAHA NMAX 150 2017 Owner's Manual

Periodic maintenance an d a djustment
6-37
6
10. Place the taillight unit in the origi-
nal position, and then install the
screws and quick fasteners.
11. Install the taillight cover by install- ing the screws.
12. Install the grab bar by installing the bolts, and then tightening them to
the specified torque.
13. Close the seat.
EAU43054
Replacin g a front turn si gnal
lig ht bul b
1. Place the vehicle on the center-
stand.
2. Remove the turn signal light bulb socket (together with the bulb) by
turning it counterclockwise.
3. Remove the burnt-out bulb by pulling it out.
4. Insert a new bulb into the socket.
5. Install the socket (together with the bulb) by turning it clockwise.
Tightening torque:
Grab bar bolt: 17 N·m (1.7 kgf·m, 12 lb·ft)
1. Turn signal light bulb socket
1. Turn signal light bulb
1
1
UBV3E0E0.book Page 37 Monday, September 26, 2016 3:42 PM

Periodic maintenance an d a djustment
6-38
6
EAU67320
Replacin g a rear turn si gnal
li g ht bul b
1. Open the seat. (See page 3-16.)
2. Remove the grab bar by removing
the bolts.
3. Remove the taillight cover by re- moving the screws.
4. Remove the turn signal light bulb socket (together with the bulb) by
turning it counterclockwise. 5. Remove the burnt-out bulb by
pulling it out.
6. Insert a new bulb into the socket.
7. Install the socket (together with the bulb) by turning it clockwise.
8. Install the taillight cover by install- ing the screws.
9. Install the grab bar by installing the bolts, and then tightening them to
the specified torque.
1. Grab bar
2. Bolt
1. Taillight cover
2. Screw
1
2
12
1. Turn signal light bulb socket
1. Turn signal light bulb
1
1
UBV3E0E0.book Page 38 Monday, September 26, 2016 3:42 PM

Scooter care and stora ge
7-3
7 Cleaning the windshield
Avoid using any alkaline or strong acid
cleaner, gasoline, brake fluid, or any
other solvent. Clean the windshield
with a cloth or sponge dampened with
a neutral detergent, and after cleaning,
thoroughly wash it off with water. For
additional cleaning, use Yamaha Wind-
shield Cleaner or other quality cleaner.
Some cleaning compounds for plastics
may leave scratches on surfaces of the
windshield. Before using them, make a
test by polishing an area which does
not affect your visibility.
After cleanin
g
1. Dry the scooter with a chamois or an absorbing cloth.
2. Use a chrome polish to shine chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally in-
duced discoloring of stainless-
steel exhaust systems can be re-
moved through polishing.)
3. To prevent corrosion, it is recom- mended to apply a corrosion pro-
tection spray on all metal,
including chrome- and nickel-plat-
ed, surfaces.
4. Use spray oil as a universal clean- er to remove any remaining dirt.
5. Touch up minor paint damage caused by stones, etc.
6. Wax all painted surfaces.
7. Let the scooter dry completely be- fore storing or covering it.
WARNING
EWA10943
Contaminants on the brakes or tires
can cause loss of control. 
Make sure that there is no oil or
wax on the brakes or tires. If
necessary, clean the brake
d iscs an d b rake linin gs with a
re gular brake disc cleaner or
acetone, an d wash the tires with
warm water an d a mil d d eter-
g ent.
 Before operatin g the scooter
test its brakin g performance
an d cornerin g b ehavior.
NOTICE
ECAU0022
 Apply spray oil an d wax spar-
in gly an d make sure to wipe off
any excess.
 Never apply oil or wax to any
rubber parts, plastic parts or
hea dlig ht, tailli ght and meter
lenses, but treat them with a
suita ble care prod uct.
 Avoi d using abrasive polishin g
compoun ds as they will wear
away the paint.
TIP
 Consult a Yamaha dealer for ad-
vice on what products to use.
 Washing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
on for a short period of time will
help remove the moisture from the
lens.
UBV3E0E0.book Page 3 Monday, September 26, 2016 3:42 PM

Specifications
8-2
8
Caster angle:26.0 °
Trail: 92 mm (3.6 in)
Front tire:
Type:Tubeless
Size: 110/70-13M/C 48P
Manufacturer/model:
DUNLOP/SCOOTSMART
Rear tire:
Type: Tubeless
Size: 130/70-13M/C 57P
Manufacturer/model:
DUNLOP/SCOOTSMART
Loa din g:
Maximum load:
168 kg (370 lb)
(Total weight of rider, passenger, cargo
and accessories)
Tire air pressure (measure d on col d
tires):
1 person:
Front:150 kPa (1.50 kgf/cm², 22 psi)
Rear:
rsons:2 pe Front:
150
kPa (1.50 kgf/cm², 22 psi)
Rear:
Front wheel:
Wheel type:
Cast wheel
Rim size: 13M/C x MT3.00
Rear wheel:
Wheel type:
Cast wheel
Rim size: 13M/C x MT3.50
Front brake:
Type:
Hydraulic single disc brake
Specified brake fluid: DOT 4
Rear brake:
Type:
Hydraulic single disc brake
Specified brake fluid:
DOT 4
Front suspension:
Type:Telescopic fork
Spring:
Coil spring
Shock absorber: Hydraulic damper
Wheel travel: 100 mm (3.9 in)
Rear suspension:
Type:
Unit swing
Spring: Coil spring
Shock absorber: Hydraulic damper
Wheel travel:
90 mm (3.5 in)
Electrical system:
System voltage:12 V
Ignition system:
TCI
Charging system: AC magneto
Battery:
Model:
YTZ7V
Voltage, capacity: 12 V, 6.0 Ah (10 HR)
Bul b watta ge:
Headlight:
LED
Brake/tail light: LED/10.0 W
Front turn signal light: 10.0 W
Rear turn signal light:
10.0 W
Auxiliary light: 5.0 W
Meter lighting: LED
High beam indicator light:
LED
UBV3E0E0.book Page 2 Monday, September 26, 2016 3:42 PM
250 kPa (2.50 kgf/cm², 36 psi)
250 kPa (2.50 kgf/cm², 36 psi)

Specifications
8-3
8
Turn signal indicator light:LED
Coolant temperature warning light: LED
Engine trouble warning light:
LED
ABS warning light: LED
Fuse(s):
Main fuse:
15.0 A
Main fuse 2: 7.5 A
Taillight fuse: 7.5 A
Signaling system fuse: 7.5 A
ABS control unit fuse:
7.5 A
ABS motor fuse: 30.0 A
ABS solenoid fuse: 15.0 A
UBV3E0E0.book Page 3 Monday, September 26, 2016 3:42 PM

10-1
10
Index
A
ABS ....................................................... 3-11
ABS warning light ................................... 3-3
Acceleration and deceleration ................ 5-3
Air filter and V-belt case air filter
elements ............................................. 6-17
Auxiliary light bulb, replacing ................ 6-34
B
Battery .................................................. 6-30
Brake fluid, changing ............................ 6-26
Brake fluid level, checking .................... 6-25
Brake lever, front .................................. 3-10
Brake lever, rear.................................... 3-11
Brake levers, lubricating ....................... 6-28
Brake light ............................................. 6-35
Braking.................................................... 5-3
C
Cables, checking and lubricating ......... 6-27
Care ........................................................ 7-1
Catalytic converter ................................ 3-15
Centerstand and sidestand, checking and lubricating .................... 6-28
Coolant ................................................. 6-13
Coolant temperature warning light ......... 3-3
D
Data recording, vehicle ........................... 9-2
Diagnostic connector.............................. 9-2
Dimmer switch ........................................ 3-9
E
Engine break-in....................................... 5-4
Engine oil and oil strainer...................... 6-10
Engine serial number .............................. 9-1
Engine trouble warning light ................... 3-3
F
Final transmission oil ............................ 6-12
Front and rear brake lever free play, checking ............................................. 6-23
Front and rear brake pads, checking.... 6-24
Front fork, checking .............................. 6-29
Fuel ....................................................... 3-13
Fuel consumption, tips for reducing ....... 5-4
Fuel tank cap ........................................ 3-12
Fuel tank overflow hose ........................ 3-15
Fuses, replacing.................................... 6-32
H
Handlebar switches ................................ 3-9
Headlight............................................... 6-33
High beam indicator light........................ 3-3
Horn switch ........................................... 3-10
I
Identification numbers ............................ 9-1
Ignition circuit cut-off system............... 3-18
Indicator lights and warning lights ......... 3-3
K
Keyhole shutter ...................................... 3-2
M
Main switch/steering lock....................... 3-1
Maintenance and lubrication, periodic ... 6-4
Maintenance, emission control system.................................................. 6-3
Matte color, caution ............................... 7-1
Model label ............................................. 9-1
Multi-function meter unit ........................ 3-4
P
Panels, removing and installing.............. 6-7
Parking ................................................... 5-5
Part locations ......................................... 2-1
S
Safe-riding points ................................... 1-5
Safety information .................................. 1-1
Seat ...................................................... 3-16
Sidestand ............................................. 3-17
Spark plug, checking ............................. 6-9
Specifications ......................................... 8-1
Starting off.............................................. 5-2
Starting the engine ................................. 5-1
Start switch .......................................... 3-10
Steering, checking................................ 6-29
Storage ................................................... 7-4
Storage compartments ........................ 3-16
T
Taillight bulb, replacing ........................ 6-35
Throttle grip and cable, checking and lubricating .................... 6-27
Throttle grip free play, checking........... 6-19
Tires ...................................................... 6-20
Tool kit.................................................... 6-2
Troubleshooting ................................... 6-39
Troubleshooting charts ........................ 6-40
Turn signal indicator lights ..................... 3-3
Turn signal light bulb (front), replacing ............................................ 6-37
Turn signal light bulb (rear), replacing ............................................ 6-38
Turn signal switch .................................. 3-9
V
Valve clearance .................................... 6-20
V-belt, checking ................................... 6-26
Vehicle identification number ................. 9-1
UBV3E0E0.book Page 1 Monday, September 26, 2016 3:42 PM