tires YAMAHA PW50 2010 User Guide
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2010, Model line: PW50, Model: YAMAHA PW50 2010Pages: 70, PDF Size: 1.44 MB
Page 64 of 70

MOTORCYCLE CARE AND STORAGE
8-4
1
2
3
4
5
6
7
8
9
3. Drain the carburetor float chamber
by loosening the drain bolt; this will
prevent fuel deposits from building
up. Pour the drained fuel into the
fuel tank.
4. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
5. Perform the following steps to pro-
tect the cylinder, piston rings, etc.
from corrosion.
a. Remove the spark plug cap
and spark plug.
b. Pour a teaspoonful of engine oil
into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap
from the spark plug, and then
install the spark plug and thespark plug cap.
WARNING! To
prevent damage or injury
from sparking, make sure to
ground the spark plug elec-
trodes while turning the en-
gine over.
[EWA10951]
6. Lubricate all control cables and the
pivoting points of all levers and
pedals as well as of the center-
stand.
7. Check and, if necessary, correct
the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
8. Cover the muffler outlet with a
plastic bag to prevent moisture
from entering it.
TIP
Make any necessary repairs before
storing the motorcycle.
Page 66 of 70

SPECIFICATIONS
9-2
1
2
3
4
5
6
7
8
9
Manufacturer/model:
BRIDGESTONE/KNOBBY
Manufacturer/model:
IRC/KNOBBY
Rear tire:
Type:
With tube
Size:
2.50-10 4PR
Manufacturer/model:
BRIDGESTONE/KNOBBY
Manufacturer/model:
IRC/KNOBBY
Loading:
Maximum rider weight:
25.0 kg (55 lb)
Tire air pressure (measured on cold
tires):
Front:
100 kPa (1.00 kgf/cm
2
, 15 psi)
Rear:
100 kPa (1.00 kgf/cm
2
, 15 psi)
Front wheel:
Wheel type:
Panel wheel
Rim size:
10x1.50
Rear wheel:
Wheel type:
Panel wheel
Rim size:
10x1.50
Front brake:
Type:
Drum brake
Operation:
Right hand operation
Rear brake:
Type:
Drum brake
Operation:
Left hand operation
Front suspension:
Type:
Telescopic fork
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
60.0 mm (2.36 in)
Rear suspension:
Type:
Unit swing
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
50.0 mm (1.97 in)
Electrical system:
Ignition system:
CDI
Page 69 of 70

INDEX
A
Acceleration and deceleration ................... 6-2
Air filter element, cleaning ......................... 7-8
Autolube pump, adjusting ........................ 7-16
B
Brake lever, front ....................................... 4-2
Brake lever, rear ........................................ 4-3
Brake levers, lubricating .......................... 7-16
Brake shoes, checking ............................ 7-14
Braking ...................................................... 6-2
C
Cables, checking and lubricating ............. 7-15
Carburetor, adjusting ............................... 7-10
Care ........................................................... 8-1
Centerstand, checking and lubricating .... 7-16
E
Engine break-in ......................................... 6-3
Engine idling speed ................................. 7-10
Engine oil ................................................... 4-5
Engine, starting a warm ............................. 6-1
Engine stop switch..................................... 4-1
F
Front and rear brake lever free play,
adjusting ................................................ 7-13
Front fork, checking ................................. 7-17
Fuel............................................................ 4-3
Fuel cock ................................................... 4-6
Fuel tank breather hose............................. 4-5
Fuel tank cap ............................................. 4-3
H
Handlebar switch ....................................... 4-1
I
Identification numbers ............................. 10-1
K
Kickstarter ................................................. 4-7
L
Labels, location ......................................... 1-1
M
Maintenance and lubrication, periodic ....... 7-3
Maintenance, emission control system ..... 7-2
Matte color, caution ................................... 8-1
Middle and final gear cases....................... 7-8
Model label .............................................. 10-1
P
Parking ...................................................... 6-4
Part locations............................................. 3-1
Power reduction plate, removing ............... 7-6
S
Safety information ..................................... 2-1
Seat ........................................................... 4-7
Spark arrester, cleaning ............................ 7-9
Spark plug, checking ................................. 7-5
Specifications ............................................ 9-1
Speed limiter and power reduction
plate ........................................................ 4-1
Starter (choke) lever .................................. 4-6
Starting and warming up a cold engine ..... 6-1
Starting off ................................................. 6-2
Steering, checking ................................... 7-17
Storage ...................................................... 8-3
T
Throttle cable free play, checking............ 7-11
Throttle grip and cable, checking and
lubricating.............................................. 7-15
Tires ........................................................ 7-11
Tool kit ....................................................... 7-1
Transmission oil ........................................ 7-7Troubleshooting ...................................... 7-22
Troubleshooting chart ............................. 7-24
V
Vehicle Emission Control
Information label (For Canada) ............. 10-2
Vehicle identification number .................. 10-1
W
Wheel bearings, checking ....................... 7-18
Wheel (front) ........................................... 7-18
Wheel (rear) ............................................ 7-20
Wheels .................................................... 7-13