fuel YAMAHA PW80 2010 User Guide

OPERATION AND IMPORTANT RIDING POINTS
6-4
1
2
3
4
5
6
7
8
9

EAU17191
Parking
When parking, stop the engine, and
then turn the fuel cock lever to “OFF”.
WARNING

EWA10311

Since the engine and exhaust
system can become very hot,
park in a place where pedestri-
ans or children are not likely to
touch them and be burned.

Do not park on a slope or on soft
ground, otherwise the vehicle
may overturn, increasing the
risk of a fuel leak and fire.

Do not park near grass or other
flammable materials which
might catch fire.

PERIODIC MAINTENANCE AND ADJUSTMENT
7-2
1
2
3
4
5
6
7
8
9

EAU41765
Periodic maintenance and lubrication chart
TIP


From 160 hours, repeat the maintenance intervals starting from 40 hours.

Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools, data and technical
skills.
NO. ITEM CHECK OR MAINTENANCE JOBINITIAL THEREAFTER EVERY
10
hours20
hours40
hours80
hours40
hours80
hours160
hours
1*Fuel line
Check fuel hoses for cracks or damage.Replace if necessary.
2Spark plugCheck condition.Adjust gap and clean.Replace if necessary.
3Air filter elementClean with solvent.Replace if necessary.
4*ClutchCheck operation.Adjust if necessary.
5*Front brakeCheck operation.Adjust brake lever free play.Replace brake shoes. Whenever worn to the limit
6*Rear brakeCheck operation.Adjust brake pedal free play.Replace brake shoes. Whenever worn to the limit
7*WheelsCheck runout, spoke tightness and for
damage.Tighten spokes if necessary.

PERIODIC MAINTENANCE AND ADJUSTMENT
7-26
1
2
3
4
5
6
7
8
9
8. Tighten the axle nut to the speci-
fied torque.
9. Adjust the brake pedal free play.
(See page 7-14.)

EAU25851
Troubleshooting
Although Yamaha motorcycles receive
a thorough inspection before shipment
from the factory, trouble may occur dur-
ing operation. Any problem in the fuel,
compression, or ignition systems, for
example, can cause poor starting and
loss of power.
The following troubleshooting chart
represents a quick and easy procedure
for checking these vital systems your-
self. However, should your motorcycle
require any repair, take it to a Yamaha
dealer, whose skilled technicians have
the necessary tools, experience, and
know-how to service the motorcycle
properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look like
Yamaha parts, but they are often inferi-
or, have a shorter service life and can
lead to expensive repair bills.
WARNING

EWA15141
When checking the fuel system, do
not smoke, and make sure there are
no open flames or sparks in the ar-
ea, including pilot lights from waterheaters or furnaces. Gasoline or
gasoline vapors can ignite or ex-
plode, causing severe injury or
property damage.
Tightening torque:
Axle nut:
60 Nm (6.0 m·kgf, 43.4 ft·lbf)

PERIODIC MAINTENANCE AND ADJUSTMENT
7-27
2
3
4
5
6
78
9

EAU25972
Troubleshooting chart
Check the fuel level in
the fuel tank.1. Fuel
There is
enough fuel.
There is
no fuel.
Supply fuel.
Operate the kickstarter.2. Compression
There is compression.
There is
no compression.Check the ignition.
Have a Yamaha dealer
check the vehicle.
Remove the spark plug
and check the electrodes.3. Ignition
Wet
DryWipe off with a dry cloth and correct the
spark plug gap, or replace the spark plug.
Have a Yamaha dealer check the vehicle.The engine does not start.
Have a Yamaha dealer check the vehicle.
Open the throttle halfway and operate
the kickstarter.
Check the compression.
The engine does not start.
Check the compression.

MOTORCYCLE CARE AND STORAGE
8-2
2
3
4
5
6
7
89 off any detergent residue using
plenty of water, as it is harmful
to plastic parts.


Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.

Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.

For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-
pounds for plastic may leavescratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound after
washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain or near the seaSince sea salt is extremely corrosive,
carry out the following steps after each
ride in the rain or near the sea.
1. Clean the motorcycle with cold wa-
ter and a mild detergent, after the
engine has cooled down.
NOTICE:
Do not use warm water
since it increases the corrosiveaction of the salt.

[ECA10791]

2. Apply a corrosion protection spray
on all metal, including chrome- and
nickel-plated, surfaces to prevent
corrosion.
After cleaning
1. Dry the motorcycle with a chamois
or an absorbing cloth.
2. Immediately dry the drive chain
and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine
chrome, aluminum and stain-
less-steel parts, including the ex-
haust system. (Even the thermally
induced discoloring of stain-
less-steel exhaust systems can be
removed through polishing.)
4. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal,
including chrome- and nickel-plat-
ed, surfaces.
5. Use spray oil as a universal clean-
er to remove any remaining dirt.
6. Touch up minor paint damage
caused by stones, etc.

MOTORCYCLE CARE AND STORAGE
8-3
1
2
3
4
5
6
7
8
9
7. Wax all painted surfaces.
8. Let the motorcycle dry completely
before storing or covering it.
WARNING

EWA14501
Contaminants on the brakes or tires
can cause loss of control.

Make sure that there is no oil or
wax on the tires.

If necessary, wash the tires with
warm water and a mild deter-
gent. Before riding at higher
speeds, test the motorcycle’s
braking performance and cor-
nering behavior.
NOTICE

ECA10800

Apply spray oil and wax spar-
ingly and make sure to wipe off
any excess.

Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.

Avoid using abrasive polishing
compounds as they will wear
away the paint.
TIP


Consult a Yamaha dealer for ad-
vice on what products to use.

Washing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
on for a short period of time will
help remove the moisture from the
lens.
EAU40652
Storage
Short-term
Always store your motorcycle in a cool,
dry place and, if necessary, protect it
against dust with a porous cover.
NOTICE

ECA10810

Storing the motorcycle in a
poorly ventilated room or cover-
ing it with a tarp, while it is still
wet, will allow water and humid-
ity to seep in and cause rust.

To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-
cals are stored.
Long-term
Before storing your motorcycle for sev-
eral months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. For motorcycles equipped with a
fuel cock that has an “OFF” posi-
tion: Turn the fuel cock lever to

MOTORCYCLE CARE AND STORAGE
8-4
2
3
4
5
6
7
89
“OFF”.
3. Drain the carburetor float chamber
by loosening the drain bolt; this will
prevent fuel deposits from building
up. Pour the drained fuel into the
fuel tank.
4. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
5. Perform the following steps to pro-
tect the cylinder, piston rings, etc.
from corrosion.
a. Remove the spark plug cap
and spark plug.
b. Pour a teaspoonful of engine oil
into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap
from the spark plug, and theninstall the spark plug and the
spark plug cap.
WARNING! To
prevent damage or injury
from sparking, make sure to
ground the spark plug elec-
trodes while turning the en-
gine over.

[EWA10951]

6. Lubricate all control cables and the
pivoting points of all levers and
pedals as well as of the sidestand.
7. Check and, if necessary, correct
the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
8. Cover the muffler outlet with a
plastic bag to prevent moisture
from entering it.
TIP

Make any necessary repairs before
storing the motorcycle.

9-1
1
2
3
4
5
6
7
8
9

SPECIFICATIONS
EAU2633X
Dimensions:
Overall length:
1540 mm (60.6 in)
Overall width:
640 mm (25.2 in)
Overall height:
880 mm (34.6 in)
Seat height:
635 mm (25.0 in)
Wheelbase:
1055 mm (41.5 in)
Ground clearance:
185 mm (7.28 in)
Minimum turning radius:
1700 mm (66.9 in)
Weight:
With oil and fuel:
61.0 kg (134 lb)
Noise and vibration level:
Noise level (77/311/EEC):
PW80 79.3 dB(A)
Vibration on seat (EN1032, ISO5008):
PW80 Will not exceed 0.5 m/s
2

Vibration on handlebar (EN1032, ISO5008):
PW80 Will not exceed 2.5 m/s
2

Engine:
Engine type:
Air cooled 2-stroke
Cylinder arrangement:
Forward-inclined single cylinder
Displacement:
79 cm
3

Bore
×
stroke:
47.0
×
45.6 mm (1.85
×
1.80 in)Compression ratio:
6.60 :1
Starting system:
Kickstarter
Lubrication system:
Separate lubrication (Yamaha autolube)

Engine oil:
Type:
YAMALUBE 2 or 2-stroke engine oil (JASO
FC grade) or (ISO EG-C or EG-D grade)
Engine oil quantity:
Quantity:
0.75 L (0.79 US qt, 0.66 Imp.qt)
Transmission oil:
Type:
YAMALUBE 4 (10W-40) or SAE 10W-40
Oil change quantity:
0.65 L (0.69 US qt, 0.57 Imp.qt)
Air filter:
Air filter element:
Wet element
Fuel:
Recommended fuel:
PW80 Regular unleaded gasoline only
PW80Z Unleaded gasoline only
Fuel tank capacity:
4.9 L (1.29 US gal, 1.08 Imp.gal)
Fuel reserve amount:
1.0 L (0.26 US gal, 0.22 Imp.gal)
Carburetor:
Type
×
quantity:
VM15SC x 1
Spark plug (s):
Manufacturer/model:
PW80


NGK/BPR6HS
PW80Z NGK/BP6HS



DENSO/W20FP
Spark plug gap:
0.6–0.7 mm (0.024–0.028 in)
Clutch:
Clutch type:
Wet, multiple-disc automatic
Transmission:
Primary reduction system:
Helical gear
Primary reduction ratio:
66/21 (3.143)
Secondary reduction system:
Chain drive
Secondary reduction ratio:
32/15 (2.133)
Transmission type:
Constant mesh 3-speed
Operation:
Left foot operation
Gear ratio:
1st:
39/12 (3.250)
2nd:
29/16 (1.812)
3rd:
22/17 (1.294)
Chassis:
Frame type:
Steel tube backbone
Caster angle:

INDEX
A
Air filter element, cleaning ......................... 7-8
Autolube pump, adjusting ........................ 7-19
B
Brake lever ................................................ 4-2
Brake lever, checking and lubricating ...... 7-19
Brake lever free play, adjusting ............... 7-14
Brake pedal ............................................... 4-2
Brake pedal, checking and lubricating ..... 7-19
Brake pedal free play, adjusting .............. 7-15
Brake shoes, checking ............................ 7-15
C
Cables, checking and lubricating ............. 7-18
Carburetor, adjusting ............................... 7-10
Care ........................................................... 8-1
D
Drive chain, cleaning and lubricating ....... 7-18
Drive chain slack ..................................... 7-16
E
Engine break-in ......................................... 6-3
Engine idling speed ................................. 7-11
Engine oil ................................................... 4-4
Engine, starting a warm ............................. 6-2
Engine stop switch..................................... 4-1
F
Front fork, checking ................................. 7-20
Fuel............................................................ 4-3
Fuel cock ................................................... 4-5
Fuel tank breather hose............................. 4-4
Fuel tank cap ............................................. 4-2
H
Handlebar switch ....................................... 4-1
I
Identification numbers ............................. 10-1
K
Kickstarter ................................................. 4-6
L
Labels, location ......................................... 1-1
M
Matte color, caution ................................... 8-1
Model label .............................................. 10-1
P
Parking ...................................................... 6-4
Part locations............................................. 3-1
Periodic maintenance and lubrication
chart ........................................................ 7-2
Power reduction plate................................ 4-1
Power reduction plate, removing ............... 7-6
S
Safety information ..................................... 2-1
Seat ........................................................... 4-7
Shifting ...................................................... 6-2
Shift pedal ................................................. 4-1
Shock absorber assembly ......................... 4-7
Sidestand .................................................. 4-8
Sidestand, checking and lubricating ........ 7-20
Spark arrester, cleaning ............................ 7-9
Spark plug, checking ................................. 7-5
Specifications ............................................ 9-1
Starter (choke) lever .................................. 4-6
Starting and warming up a cold engine ..... 6-1
Steering, checking ................................... 7-21
Storage ...................................................... 8-3
Supporting the motorcycle....................... 7-22
T
Throttle cable free play, adjusting ........... 7-11Throttle grip and cable, checking and
lubricating ............................................. 7-18
Tires ........................................................ 7-12
Tool kit ...................................................... 7-1
Transmission oil ........................................ 7-7
Troubleshooting ...................................... 7-26
Troubleshooting chart ............................. 7-28
V
Vehicle identification number .................. 10-1
W
Wheel bearings, checking ....................... 7-21
Wheel (front) ........................................... 7-22
Wheel (rear) ............................................ 7-25
Wheels .................................................... 7-13