steering YAMAHA SUPERJET 2008 User Guide

Operation
30
To open the fire extinguisher container:
(1) Grasp the tab, pull the band to the rear,
and then pull it up.
(2) Lift the container about 30 degrees from
the storage position.
CAUTION:
ECJ00400
Do not force the fire extinguisher contain-
er up more than 30 degrees from the stor-
age position, otherwise the container and
hood could be damaged.
(3) Remove the cap to access the fire extin-
guisher.
To close the fire extinguisher container:
(1) Insert the fire extinguisher into the con-
tainer, and then install the cap and tighten
it securely.(2) Lower the container on the hood to its
storage position and secure it with the
band.
NOTE:

To check the fire extinguisher, see the in-
structions supplied by the fire extinguisher
manufacturer. Always keep the fire extin-
guisher in the fire extinguisher container.

Always carry a fire extinguisher on board. A
fire extinguisher is not standard equipment
with this watercraft. If you do not have one,
contact a Yamaha dealer or a fire extin-
guisher dealer to obtain one meeting the
proper specifications.
EJU32590Throttle lever
Check the throttle lever for proper operation.
Squeeze and release the throttle lever several
times to make sure that there is no hesitation
in its travel. It should be smooth over the com-
plete range and spring back to the idle posi-
tion when released.
WARNING
EWJ00490
Before starting the engine, always check
the operation of the throttle lever.
EJU32600Steering system
Check the handlebars for looseness.
Turn the handlebars as far as possible to the
right and left to make sure that operation is
1Fire extinguisher holder and cover
2Ta b
UF2F70E0.book Page 30 Tuesday, April 17, 2007 9:56 AM

Operation
31
smooth and unrestricted throughout the
whole range. Also, make sure that the jet
thrust nozzle moves as the handlebars are
turned, and that there is no free play between
the handlebars and the jet thrust nozzle.
EJU32620Steering pole
Check the steering pole for looseness.
Move the steering pole up and down to make
sure that operation is smooth and unrestricted
throughout the whole range. Also, make sure
that the steering pole does not have any side
play.
EJU32650Jet intake
Carefully check the jet intake for weeds, de-
bris, or anything else that might restrict the in-
take of water. If the jet intake is clogged,
cavitation could occur, reducing jet thrust, and
possibly damaging the jet pump.
In some cases, the engine may overheat be-
cause of lack of cooling water, and damage tothe engine could result. Cooling water is fed to
the engine by the jet pump. (See page 65 for
jet intake cleaning procedures.)
WARNING
EWJ00470

Keep away from the intake grate while
the engine is on. Items such as long hair,
loose clothing, or PFD straps can be-
come entangled in moving parts, result-
ing in severe injury or drowning.

Stop the engine and remove the clip
from the engine shut-off switch before
removing any debris or weeds, which
may have collected around the jet in-
take.
UF2F70E0.book Page 31 Tuesday, April 17, 2007 9:56 AM

Operation
41
NOTE:

To efficiently discharge water from the en-
gine compartment, operate the watercraft
as straight as possible and above planing
speed for at least 2 minutes.

To stabilize the watercraft when accelerat-
ing to planing speed, maintain a low center
of gravity by operating it in the kneeling po-
sition.
EJU33240Turning the watercraft
Steering control depends on the combination
of handlebar position and the amount of throt-
tle.
Water sucked in through the intake grate is
pressurized by the impeller in the jet pump. As
the pressurized water is expelled from the
pump through the jet thrust nozzle, it creates
thrust to move and steer the watercraft. The
higher the engine speed, the more thrust pro-
duced.
The amount of jet thrust, in addition to the po-
sition of the handlebars, determines how
sharply you turn.
A. More throttle produces higher thrust, so
the watercraft will turn more sharply.B. Less throttle produces lower thrust, so
the watercraft will turn more gradually.
C. Releasing the throttle lever completely
produces only minimum thrust. If you are
traveling at speeds above trolling, you will
have rapidly decreasing ability to steer
without throttle. You may still have some
turning ability immediately after releasing
the throttle lever, but once the engine
slows down, the watercraft will no longer
respond to handlebar input until you ap-
ply throttle again or you reach trolling
speed.
At trolling speed, the watercraft can be
turned gradually by handlebar position
alone using just the amount of thrust
available at idle.
UF2F70E0.book Page 41 Tuesday, April 17, 2007 9:56 AM

Operation
43

Operate defensively at safe speeds and
keep a safe distance away from people,
objects, and other watercraft to give you
time to stop.

Do not shut the engine off when slowing
down in case you need engine power to
steer away from a boat or other obstacle
that comes into your path.
EJU33300Beaching the watercraft
(1) Make sure that there are no boats, swim-
mers, or obstacles near the beach. Re-
lease the throttle lever about 90 m (300 ft)
before you reach the intended beaching
area.
(2) Approach the beach slowly and stop the
engine before reaching land.
Remember, you need throttle to steer.
(3) Get off the watercraft and pull it up on the
beach.
CAUTION:
ECJ00490
Small pebbles, sand, seaweed, and other
debris can be sucked into the jet intake
and impair or damage the impeller. Always
stop the engine and get off the watercraft
before beaching it.
EJU33330Rough water operation
The force of landing after jumping can cause
a strong impact on both the watercraft and the
operator. It is possible for the operator to hit
his or her chest or jaw on the watercraft or
handlebars and be injured.
Do not operate the watercraft with your chin
right above the handlebars or with your feet
outside the watercraft.
Operating in rough water or jumping waves
can also crack the watercraft hull and damage
internal parts. Avoid operating in rough water
or bad weather conditions.
EJU33361
Post-operation care
To keep your watercraft in top shape, always
take it out of the water after using it and per-
form the following procedures. Leaving the
watercraft in the water for extended periods
will accelerate the rate of normal deterioration
of the jet unit components and hull finish. Ma-
rine organisms and corrosion are some of the
conditions that can adversely affect the life of
many watercraft components.
(1) Remove the watercraft from the water.
(2) Wash down the hull, steering pole, han-
dlebars, and jet unit with fresh water.
(3) Remove the hood and check the engine
compartment for water. To drain excess
water, turn the watercraft on its port (left)
side. If necessary, turn the watercraft up-
side down to drain the water completely.
CAUTION:
ECJ00580

Place a suitable clean cloth or carpeting
underneath the watercraft to protect it
from abrasions and scratches.

Always turn the watercraft over onto its
port (left) side.

When turning the watercraft onto its
side or inverting it, support the bow and
secure the steering pole, otherwise the
steering pole and handlebars could be
bent or damaged.
NOTE:
This watercraft is equipped with an automatic
bilge draining system that removes water
from the engine compartment while you are
underway. However, some residual water will
remain.
(4) Place the watercraft in a horizontal posi-
tion.
UF2F70E0.book Page 43 Tuesday, April 17, 2007 9:56 AM

Operation
44
(5) Flush the cooling system to prevent it
from clogging with salt, sand, or dirt. (See
page 46 for flushing procedures.)
(6) Drain residual water from the exhaust
system by alternately squeezing and re-
leasing the throttle lever for 10 to 15 sec-
onds while the engine is running.
CAUTION:
ECJ00561
Do not run the engine for more than 15
seconds without supplying water, other-
wise the engine could overheat.
(7) If the watercraft will be stored for a week
or more, lubricate internal engine compo-
nents to help prevent corrosion. (See
page 47 for lubrication procedures.)
(8) Rinse the engine and engine compart-
ment with a small amount of water.
CAUTION:
ECJ00570
Do not use high-pressure water when rins-
ing the engine or engine compartment as
severe engine damage could result.
(9) Wipe the engine and engine compart-
ment dry with a clean cloth (repeat step 3,
if necessary).
(10) Wipe the hull, steering pole, handlebars,
and jet unit dry with a clean cloth.
(11) Spray a rust inhibitor on metallic parts to
minimize corrosion.
(12) Allow the engine compartment to air dry
completely before installing the hood.
EJU33420
Transporting
WARNING
EWJ00750
Always turn the fuel cock knob to “OFF”
when transporting the watercraft, other-
wise fuel could leak out into the engine or
engine compartment, which would create
a fire hazard.
Transport this watercraft using a special trail-
er that incorporates a hole into which the pin
can be inserted and locked after passing it
through the bow rope hole.
After securing the bow with the pin, secure the
stern with ropes or tie downs routed over the
1Pin
2Bow rope hole
UF2F70E0.book Page 44 Tuesday, April 17, 2007 9:56 AM

Operation
45
gunwale. Use a rubber shock cord to secure
the steering pole.
CAUTION:
ECJ00630

Do not route ropes or tie downs over the
steering pole, as they could damage it.
Also, wrap the ropes or tie downs with
towels or rags where they touch the
body of the watercraft to avoid scratch-
ing or damage.

Do not transport the watercraft with the
steering pole up, otherwise the steering
pole could be damaged.
1Rubber shock cord
2Tie down
UF2F70E0.book Page 45 Tuesday, April 17, 2007 9:56 AM

Maintenance and care
47
(8) Remove the garden hose adapter and in-
stall the flushing hose connector cap.
EJU33561Lubrication
WARNING
EWJ00300
To reduce the risk of fire or explosion:
Never pour or spray gasoline, or any sub-
stance other than a rust inhibitor through
the hole in the carburetor silencer cover.
CAUTION:
ECJ00151

Be sure to install the silencer cap se-
curely after fogging the engine, other-
wise water could enter the engine and
cause damage.

Do not run the engine for more than 15
seconds without supplying water, other-
wise the engine could overheat.
(1) Remove the silencer cap.
(2) Start the engine with the watercraft in a
well-ventilated area.
(3) With the engine running at a fast idle,
quickly spray as much rust inhibitor as
possible through the hole in the silencer
cover. Keep spraying until the engine
stalls (or a maximum of 15 seconds).
(4) Install the silencer cap securely.
(5) Lubricate all cables such as the throttle,
choke, and steering cables.
NOTE:
Use a suitable marine grease applicator to
pressure-lubricate the cables and purge out
any moisture between the inner and outer ca-
bles.
(6) Lubricate the areas of the watercraft
specified in “Lubrication points” on page
58.
EJU33640Fuel system
WARNING
EWJ00290
GASOLINE AND ITS VAPORS ARE HIGH-
LY FLAMMABLE AND EXPLOSIVE!

Do not smoke when refueling, and keep
away from sparks, flames, and other
sources of ignition.

Stop the engine before refueling.

Refuel in a well-ventilated area with the
watercraft in a horizontal position.

Do not stand or sit on the watercraft
while refueling in case of fire.

Take care not to spill gasoline. If gaso-
line spills, wipe it up immediately with
dry rags. Always properly dispose of
gasoline-soaked rags.

Avoid overfilling the fuel tank. Stop fill-
ing when the fuel level just reaches the
bottom of the filler tube. Do not fill up the
filler tube because fuel expands as it
warms up and could overflow. If tempo-
rarily leaving the watercraft with a full
fuel tank, do not leave it in direct sun-
light. Leave it in a well-ventilated area
with the watercraft in a horizontal posi-
tion.

Tighten the fuel tank filler cap securely
after refueling.

If you should swallow some gasoline, in-
hale a lot of gasoline vapor, or get gaso-
1Silencer cap
UF2F70E0.book Page 47 Tuesday, April 17, 2007 9:56 AM

Maintenance and care
51
EJU33820Periodic maintenance chart
The following chart gives general guidelines for periodic maintenance. However, maintenance
may need to be performed more frequently depending on your operating conditions.
This “” mark indicates maintenance that you may do yourself.
This “” mark indicates work to be done by a Yamaha dealer.
Item OperationInitial Thereafter every
Page 10
hours50
hours100
hours100
hours200
hours
6
months12
months12
months24
months
Spark plugsCheck, clean, adjust 57
Lubrication pointsLubricate 58
Intermediate hous-
ingLubricate 58
Fuel systemCheck 53
Fuel filterCheck, clean, replace 53
Fuel tankCheck, clean 53
CarburetorCheck, adjust 61
Trolling speedCheck, adjust 61
Carburetor throt-
tle shaftCheck—
Cooling water pas-
sagesFlush
*46
Bilge strainerClean—
ImpellerCheck—
Jet thrust nozzle
angleCheck, adjust 53
Handlebar pivot
shaftCheck—
Steering frictionCheck, adjust 54
Throttle cableCheck, adjust 56
Choke cableCheck, adjust 59
BatteryCheck, charge 60
Rubber couplingCheck—
Engine mountCheck—
UF2F70E0.book Page 51 Tuesday, April 17, 2007 9:56 AM

Maintenance and care
54
Turn the handlebars as far as possible to the
right and left and check that the difference of
distances A and B between the jet thrust noz-
zle and the nozzle is within specification.
If the steering is stiff or misadjusted, have a
Yamaha dealer service it.
EJU34331Adjusting the steering friction
The amount of friction in the steering can be
adjusted to suit operator preference.To adjust the steering friction:
(1) Lift the steering pole and support it with
the lock pin.
(2) Remove the four screws, and then re-
move the handlebar cover.
(3) Turn the handlebars so that the left han-
dlebar grip is facing down. Difference of A and B:
Maximum 5 mm (0.20 in)
1Steering pole
2Lock pin
1Adjusting nut
2Locknut
UF2F70E0.book Page 54 Tuesday, April 17, 2007 9:56 AM

Maintenance and care
55
(4) Loosen the locknut.
(5) Tighten or loosen the adjusting nut until
the desired amount of friction is obtained.
(6) Hold the adjusting nut with one wrench
while tightening the locknut with another
wrench.
(7) Install the handlebar cover and the four
screws.
EJU31282Adjusting the jet thrust nozzle angle
The angle of the jet thrust nozzle can be ad-
justed to suit operator preference according to
the following procedure.
To change the steering cable pivot bolt posi-
tion:
(1) Remove the two screws, and then re-
move the steering pole cover.(2) Pull back the outer sleeve of the steering
cable joint, and then disconnect the joint
from the steering cable pivot bolt.
(3) Remove the steering cable pivot bolt.
(4) Select the nozzle angle, install the steer-
ing cable pivot bolt with the lock washer in
the desired position (P1 or P2) on the Tightening torque:
29.0 Nm (21.4 ft-lb) (2.96 kgf-m)
1Steering pole cover
1Steering cable joint
1Steering cable pivot bolt
2Steering column
UF2F70E0.book Page 55 Tuesday, April 17, 2007 9:56 AM