check engine YAMAHA TDR 125 2001 User Guide

6-3
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
9
*Tires¥Check tread depth and for damage.
¥Replace if necessary.
¥Check air pressure.
¥Correct if necessary.ÖÖÖÖ
10*Wheel bearings¥Check bearing for looseness or damage.ÖÖÖÖ
11*Swingarm¥Check swingarm pivoting point for play.ÖÖÖÖ
¥Lubricate with lithium-soap-based grease.Every 24,000km
12Drive chain¥Check chain slack.
¥Make sure that the rear wheel is properly aligned.
¥Clean and lubricate.Every 1,000 km and after washing the motorcycle
or riding in the rain.
13*Steering bearings¥Check bearing play and steering for roughness.ÖÖÖÖÖ
¥Lubricate with lithium-soap-based greaseEvery 24,000km
14*Chassis fasteners¥Make sure that all nuts, bolts and screws are properly tightened.ÖÖÖÖÖ
15Sidestand¥Check operation.
¥Lubricate.ÖÖÖÖÖ
16*Sidestand switch¥Check operation.ÖÖÖÖÖÖ
17*Front fork¥Check operation and for oil leakage.ÖÖÖÖ
18*Rear shock absorber
assembly¥Check operation and shock absorber for oil leakage.ÖÖÖÖ
¥Lubricate the pivoting points with molybdenum disulfide
grease.ÖÖ
19*Carburetor¥Check starter (choke) operation.
¥Adjust engine idling speed.ÖÖÖÖÖÖ NO.ITEMCHECK OR MAINTENANCE JOBODOMETER READING (´1,000 km)
ANNUAL
CHECK
16121824
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 38

1
2.Remove the spark plug as
shown, with the spark plug
wrench included in the ownerÕs
tool kit.To check the spark plug
1.Check that the porcelain insula-
tor around the center electrode
of the spark plug is a medium-to-
light tan (the ideal color when the
motorcycle is ridden normally).
NOTE:
If the spark plug shows a distinctly
different color, the engine could be
defective. Do not attempt to diagnose
such problems yourself. Instead,
have a Yamaha dealer check the
motorcycle.2.Check the spark plug for elec-
trode erosion and excessive car-
bon or other deposits, and
replace it if necessary.
1.Spark plug wrench
6-7
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9Specified spark plug:
BR9ES (NGK)
1
EAU01833
Checking the spark plugThe spark plug is an important
engine component, which is easy to
check. Since heat and deposits will
cause any spark plug to slowly erode,
the spark plug should be removed
and checked in accordance with the
periodic maintenance and lubrication
chart. In addition, the condition of the
spark plug can reveal the condition of
the engine.
To remove the spark plug
1.Remove the spark plug cap.1.Spark plug cap
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 42

6-8
NOTE:
If a torque wrench is not available
when installing a spark plug, a good
estimate of the correct torque is
1/4Ð1/2 turn past finger tight.
However, the spark plug should be
tightened to the specified torque as
soon as possible.4.Install the spark plug cap.
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9 Spark plug gap:
0.7Ð0.8 mm
Tightening torque:
Spark plug:
20 Nm (2.0 m0kg)
a
a.Spark plug gapTo install the spark plug
1.Measure the spark plug gap with
a wire thickness gauge and, if
necessary, adjust the gap to
specification.
2.Clean the surface of the spark
plug gasket and its mating sur-
face, and then wipe off any grime
from the spark plug threads.
3.Install the spark plug with the
spark plug wrench, and then
tighten it to the specified torque.
EAU03751
Transmission oilThe transmission oil level should be
checked before each ride. In addition,
the transmission oil must be changed
at the intervals specified in the peri-
odic maintenance and lubrication
chart.
To check the transmission oil level
1.Place the motorcycle on a level
surface and hold it in an upright
position. NOTE:
Make sure that the motorcycle is
positioned straight up when checking
the oil level. A slight tilt to the side
can result in a false reading.2.Start the engine, warm it up for
several minutes, and then turn it
off.
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 43

1
4.Install the transmission oil drain
bolt, and then tighten it to the
specified torque.
5.Add the specified amount of the
recommended transmission oil,
and then install and tighten the
oil filler cap.1.Transmission oil drain bolt
6-9
1
1.Oil filler capTo change the transmission oil
1.Start the engine, warm it up for
several minutes, and then turn it
off.
2.Place an oil pan under the trans-
mission to collect the used oil.
3.Remove the oil filler cap and
drain bolt to drain the oil from the
transmission.
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9Tightening torque:
Transmission oil drain bolt:
15 Nm (1.5 m0kg)
1
2
1.Check window
2.Minimum level mark3.Wait a few minutes until the oil
settles, and then check the oil
level through the check window
located at the right side of the
crankcase.NOTE:
The transmission oil should be above
the minimum level mark.4.If the oil is below the minimum
level mark, remove the oil filler
cap, add sufficient oil of the rec-
ommended type to raise it to the
correct level, and then install and
tighten the cap.
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 44

6-10
EC000077
cC8In order to prevent clutch slip-
page (since the transmission
oil also lubricates the clutch),
do not mix any chemical addi-
tives with the oil.
8Make sure that no foreign
material enters the transmis-
sion.6.Start the engine, and then let it
idle for several minutes while
checking the transmission for oil
leakage. If oil is leaking, immedi-
ately turn off the engine and
check for the cause.
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9 Recommended transmission oil:
See page 8-1
Oil quantity:
Periodic oil change:
0.75 L
Total amount (dry transmission):
0.8 L
1
2
1.Maximum level mark
2.Minimum level mark2.Check the coolant level in the
coolant reservoir.NOTE:
The coolant should be between the
minimum and maximum level marks.3.If the coolant is at or below the
minimum level mark, open the
reservoir cap, add coolant to the
maximum level mark, and then
close the reservoir cap.
EAU03761
CoolantTo check the coolant level
1.Place the motorcycle on a level
surface and hold it in an upright
position.NOTE:
8The coolant level must be
checked on a cold engine since
the level varies with engine tem-
perature.
8Make sure that the motorcycle is
positioned straight up when
checking the coolant level. A
slight tilt to the side can result in
a false reading.
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 45

6-12
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
1
NOTE:
Check the washer for damage and
replace it if necessary.9.Install the reservoir tank hose.1.Hose
Tightening torque:
Coolant drain bolt:
8 Nm (0.8 m0kg)
10.Pour the recommended coolant
into the radiator until it is full.
Antifreeze/water mixture ratio:
1:1
Recommended antifreeze:
High-quality ethylene glycol
antifreeze containing corrosion
inhibitors for aluminum engines
Coolant quantity:
Total amount:
1.05 L
Coolant reservoir capacity:
0.35 L
EC000080
cC8If coolant is not available, use
distilled water or soft tap water
instead. Do not use hard water
or salt water since it is harmful
to the engine.
8If water has been used instead
of coolant, replace it with
coolant as soon as possible,
otherwise the engine may not
be sufficiently cooled and the
cooling system will not be pro-
tected against frost and corro-
sion.
8If water has been added to the
coolant, have a Yamaha dealer
check the antifreeze content of
the coolant as soon as possi-
ble, otherwise the effective-
ness of the coolant will be
reduced. 11.Install the radiator cap, start the
engine, let it idle for several min-
utes, and then turn it off.
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 47

6-13
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
21
4
5
3
1.Coolant reservoir tank cap
2.Stopper
3.Screw
4.Maximum level mark
5.Minimum level mark12.Remove the radiator cap to
check the coolant level in the
radiator. If necessary, add suffi-
cient coolant until it reaches the
top of the radiator, and then
install the radiator cap.
13.Check the coolant level in the
reservoir. If necessary, remove
the coolant reservoir cap by
removing the screw and stopper,
add coolant to the maximum
level mark, and then install the
cap, stopper and screw.14.Start the engine, and then check
the vehicle for coolant leakage. If
coolant is leaking, have a
Yamaha dealer check the cool-
ing system.
15.Install the cowling, radiator cover
and seat.
1
EAU03747
Cleaning the air filter
elementThe air filter element should be
cleaned at the intervals specified in
the periodic maintenance and lubrica-
tion chart. Clean the air filter element
more frequently if you are riding in
unusually wet or dusty areas.
1.Remove the seat. (See page
3-12 for seat removal and instal-
lation procedures.)
2.Remove cowlings A and B. (See
page 6-6 for cowling removal
and installation procedures.)
3.Remove the fuel tank bolt.1.Bolt
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 48

6-16
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
EAU00632
Adjusting the engine idling
speedThe engine idling speed must be
checked and, if necessary, adjusted
as follows at the intervals specified in
the periodic maintenance and lubrica-
tion chart.
1.Start the engine and warm it up
for several minutes at
1,000Ð2,000 r/min while occa-
sionally revving it to 4,000Ð5,000
r/min.NOTE:
The engine is warm when it quickly
responds to the throttle.
2.Check the engine idling speed
and, if necessary, adjust it to
specification by turning the throt-
tle stop screw. To increase the
engine idling speed, turn the
screw in direction a. To
decrease the engine idling
speed, turn the screw in direction
b.
Engine idling speed:
1,300Ð1,500 r/min
1,400Ð1,500 r/min (A, CH only)
ba
1
1.Throttle stop screw
NOTE:
If the specified idling speed cannot
be obtained as described above,
have a Yamaha dealer make the
adjustment.
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 51

6-17
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
EAU00634
Adjusting the throttle cable
free playThe throttle cable free play should
measure 3Ð5 mm at the throttle grip.
Periodically check the throttle cable
free play and, if necessary, adjust it
as follows.NOTE:
The engine idling speed must be cor-
rectly adjusted before checking and
adjusting the throttle cable free play.a.Free play
a
2 1
b
a
1.Loosen the locknut.
2.To increase the throttle cable
free play, turn the adjusting nut
in direction a. To decrease the
throttle cable free play, turn the
adjusting nut in direction b.
3.Tighten the locknut.1.Locknut
2.Adjusting nut
EAU03804
TiresTo maximize the performance, dura-
bility, and safe operation of your
motorcycle, note the following points
regarding the specified tires.
Tire air pressure
The tire air pressure should be
checked and, if necessary, adjusted
before each ride.
EW000082
w8The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the tempera-
ture of the tires equals the
ambient temperature).
8The tire air pressure must be
adjusted in accordance with
the riding speed and with the
total weight of rider, passen-
ger, cargo, and accessories
approved for this model.
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 52

6-27
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
EAU02962
Checking and lubricating the
cablesThe operation of all control cables
and the condition of the cables
should be checked before each ride,
and the cables and cable ends
should be lubricated if necessary. If a
cable is damaged or does not move
smoothly, have a Yamaha dealer
check or replace it.
Recommended lubricant:
Engine oil
EW000112
wDamage to the outer sheath may
interfere with proper cable opera-
tion and will cause the inner cable
to rust. Replace a damaged cable
as soon as possible to prevent
unsafe conditions.
2.Wipe the drive chain dry.
3.Thoroughly lubricate the drive
chain with a special O-ring chain
lubricant.
ECA00052
cCDo not use engine oil or any other
lubricants for the drive chain, as
they may contain substances that
could damage the O-rings.
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 62