wheel YAMAHA TDR 125 2001 User Guide

6-37
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
1
1.Speedometer cable
EAU03239
Front wheelTo remove the front wheel
EW000122
w8It is advisable to have a
Yamaha dealer service the
wheel.
8Securely support the motorcy-
cle so that there is no danger
of it falling over.1.Disconnect the speedometer
cable from the front wheel.
EAU01579
Supporting the motorcycleSince this model is not equipped with
a centerstand, follow these precau-
tions when removing the front and
rear wheel or performing other main-
tenance requiring the motorcycle to
stand upright. Check that the motor-
cycle is in a stable and level position
before starting any maintenance. A
strong wooden box can be placed
under the engine for added stability.
To service the front wheel
1.Stabilize the rear of the motorcy-
cle by using a motorcycle stand
or, if an additional motorcycle
stand is not available, by placing
a jack under the frame in front of
the rear wheel.
2.Raise the front wheel off the
ground by using a motorcycle
stand.To service the rear wheel
Raise the rear wheel off the ground
by using a motorcycle stand or, if a
motorcycle stand is not available, by
placing a jack either under each side
of the frame in front of the rear wheel
or under each side of the swingarm.
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 72

6-38
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
2
1
1.Pinch bolt
2.Wheel axle2.Loosen the front wheel axle
pinch bolt, then the wheel axle.
3.Lift the front wheel off the ground
according to the procedure on
page 6-37.
4.Pull the wheel axle out, and then
remove the wheel.
ECA00048
cCDo not apply the brake after the
wheel has been removed together
with the brake disc, otherwise the
brake pads will be forced shut.
1
3.Insert the wheel axle.
4.Lower the front wheel so that it is
on the ground.
5.Push down hard on the handle-
bar several times to check for
proper fork operation.
6.Tighten the wheel axle to the
specified torque.
7.Install the front wheel axle pinch
bolt, and then tighten it to the
specified torque. Tightening torque:
Wheel axle:
59 Nm (5.9 m0kg)
1
EAU01394
To install the front wheel
1.Install the speedometer gear unit
into the wheel hub so that the
projections mesh with the slots.
2.Lift the wheel up between the
fork legs.NOTE:
Make sure that there is enough
space between the brake pads
before inserting the brake disc and
that the slot in the speedometer gear
unit fits over the retainer on the fork
leg.1.Speedometer gear unit1.Retainer
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 73

6-39
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
2.Lift the rear wheel off the ground
according to the procedure on
page 6-37.
3.Remove the axle nut.
4.Loosen the locknut and the
adjusting nut on each end of the
swingarm.
5.Push the wheel forward, and
then remove the drive chain from
the rear sprocket.NOTE:
The drive chain does not need to be
disassembled in order to remove and
install the wheel.
1
2
3
EAU03755
Rear wheelTo remove the rear wheel
EW000122
w8It is advisable to have a
Yamaha dealer service the
wheel.
8Securely support the motorcy-
cle so that there is no danger
of it falling over.1.Loosen the axle nut.1.Axle nut
2.Lock nut
3.Adjusting nut
8.Connect the speedometer cable. Tightening torque:
Front wheel axle pinch bolt:
20 Nm (2.0 m0kg)
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 74

6-40
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9 6.While supporting the brake
caliper, pull the wheel axle out.
7.Remove the wheel.
ECA00048
cCDo not apply the brake after the
wheel has been removed together
with the brake disc, otherwise the
brake pads will be forced shut.
1
EAU01620
To install the rear wheel
1.Install the brake caliper onto the
swingarm as shown.NOTE:
Make sure that the slot in the brake
caliper bracket fits over the retainer
on the swingarm.2.Install the drive chain onto the
rear sprocket.
3.Insert the wheel axle from the
left-hand side, install the axle
nut, and then lower the rear
wheel so that it is on the ground.
NOTE:
Make sure that there is enough
space between the brake pads
before inserting the brake disc
between the brake pads.4.Adjust the drive chain slack.
(See page 6-26 for drive chain
slack adjustment procedures.)
5.Tighten the axle nut to the speci-
fied torque.
Tightening torque:
Axle nut:
104 Nm (10.4 m0kg)
1.Retainer
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 75

7-1
CareWhile the open design of a motorcy-
cle reveals the attractiveness of the
technology, it also makes it more vul-
nerable. Rust and corrosion can
develop even if high-quality compo-
nents are used. A rusty exhaust pipe
may go unnoticed on a car, however,
it detracts from the overall appear-
ance of a motorcycle. Frequent and
proper care does not only comply
with the terms of the warranty, but it
will also keep your motorcycle looking
good, extend its life and optimize its
performance.Before cleaning
1.Cover the muffler outlet with a
plastic bag after the engine has
cooled down.
2.Make sure that all caps and cov-
ers as well as all electrical cou-
plers and connectors, including
the spark plug cap, are tightly
installed.
3.Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such
products onto seals, gaskets,
sprockets, the drive chain and
wheel axles. Always rinse the dirt
and degreaser off with water.Cleaning
ECA00010
cC8Avoid using strong acidic
wheel cleaners, especially on
spoked wheels. If such prod-
ucts are used on hard-to-
remove dirt, do not leave the
cleaner on the affected area
any longer than instructed.
Also, thoroughly rinse the area
off with water, immediately dry
it, and then apply a corrosion
protection spray.
8Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or
sponge with mild detergent
and water to clean plastic.
EAU03521
MOTORCYCLE CARE AND STORAGE
1
2
3
4
5
67
8
9
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 79

1
2
3
4
5
67
8
9
7-2
8Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abra-
sive cleaning products, sol-
vent or thinner, fuel (gasoline),
rust removers or inhibitors,
brake fluid, antifreeze or elec-
trolyte.
8Do not use high-pressure
washers or steam-jet cleaners
since they cause water seep-
age and deterioration in the
following areas: seals (of
wheel and swingarm bearings,
fork and brakes), electric com-
ponents (couplers, connec-
tors, instruments, switches
and lights), breather hoses
and vents.8For motorcycles equipped
with a windshield: Do not use
strong cleaners or hard
sponges as they will cause
dulling or scratching. Some
cleaning compounds for plas-
tic may leave scratches on the
windshield. Test the product
on a small hidden part of the
windshield to make sure that it
does not leave any marks. If
the windshield is scratched,
use a quality plastic polishing
compound after washing.
After normal useRemove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottle-
brush for hard-to-reach areas.
Stubborn dirt and insects will come
off more easily if the area is covered
with a wet cloth for a few minutes
before cleaning.After riding in the rain, near the sea
or on salt-sprayed roadsSince sea salt or salt sprayed on
roads during winter are extremely
corrosive in combination with water,
carry out the following steps after
each ride in the rain, near the sea or
on salt-sprayed roads.NOTE:
Salt sprayed on roads in the winter
may remain well into spring.1.Clean the motorcycle with cold
water and a mild detergent, after
the engine has cooled down.
ECA00012
cCDo not use warm water since it
increases the corrosive action of
the salt.2.Apply a corrosion protection
spray on all metal, including
chrome- and nickel-plated, sur-
faces to prevent corrosion.
MOTORCYCLE CARE AND STORAGE
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 80

1
2
3
4
5
6
7
8
9
7-5
6.Lubricate all control cables and
the pivoting points of all levers
and pedals as well as of the
sidestand/centerstand.
7.Check and, if necessary, correct
the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground.
Alternatively, turn the wheels a
little every month in order to pre-
vent the tires from becoming
degraded in one spot.
8.Cover the muffler outlet with a
plastic bag to prevent moisture
from entering it.
9.Remove the battery and fully
charge it. Store it in a cool, dry
place and charge it once a
month. Do not store the battery
in an excessively cold or warm
place (less than 0 ¡C) or more
than 30 ¡C). For more informa-
tion on storing the battery, see
page 6-33.
NOTE:
Make any necessary repairs before
storing the motorcycle.
MOTORCYCLE CARE AND STORAGE
7
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 83

SPECIFICATIONS
1
2
3
4
5
6
78
9
Specifications
ModelTDR125
Dimensions
Overall length2,120 mm
(F, GB, IRL, B, P, GR, E)
2,185 mm (S, SF, D, CH, A)
Overall width840 mm
Overall height1,295 mm
Seat height850 mm
Wheel base1,405 mm
Ground clearance270 mm
Minimum turning radius2,200 mm
Basic weight (with oil and full
fuel tank)135 kg
136 kg (CH, A)
Engine
Engine typeLiquid cooled 2-stroke,
gasoline
Cylinder arrangementForward inclined single
cylinder
Displacement125 cm
3
Bore ´Stroke56.0 ´50.7 mm
Compression ratio6.6:1
Starting systemElectric starter
Lubrication systemSeparate lubrication
(Yamaha Autolube)Engine oil (2-cycle)
TypeYamalube 2 or equivalent
2-stroke engine oil
Capacity
Total amount1.2 L
Transmission oil
TypeSAE 10W30 SE motor oil
Capacity
Periodic oil change0.75 L
Total amount0.8 L
Cooling system capacity
(total amount)1.05 L
Air filterWet type element
Fuel
TypeRegular unleaded gasoline
Fuel tank capacity11 L
Reserve amount2.2 L
Carburetor
ManufacturerMIKUNI
Model ´quantityTM28SS ´1
EAU01038
SPECIFICATIONS
8-1
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 84

SPECIFICATIONS
1
2
3
4
5
6
78
9
Wheels
Front
TypeCast
Size18 ´MT2.15
Rear
TypeCast
Size17 ´MT2.50
Brakes
Front
TypeSingle disc brake
OperationRight hand
FluidDOT 4
Rear
TypeSingle disc brake
OperationRight foot
FluidDOT 4
Suspension
Front
TypeTelescopic fork
Rear
TypeSwingarm (Monocross)Spring/shock absorber
Front
TypeCoil spring / oil damper
Rear
TypeCoil-gas spring / oil damper
Wheel travel
Front180 mm
Rear180 mm
Electrical
Ignition systemC.D.I.
Charging system
TypeC.D.I. magneto
Standard output14 V, 12A @5,000 r/min
Battery
TypeYTX5L-BS
Voltage, capacity12 V, 4 AH
Headlight typeQuartz bulb (halogen)
Bulb voltage, wattage ´quantity
Headlight12 V, 60/55W ´2
12 V, 35/35W ´2 (GB, IRL)
8-3
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 86