1
2
3
4
5
67
8
9
7-2
8Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abra-
sive cleaning products, sol-
vent or thinner, fuel (gasoline),
rust removers or inhibitors,
brake fluid, antifreeze or elec-
trolyte.
8Do not use high-pressure
washers or steam-jet cleaners
since they cause water seep-
age and deterioration in the
following areas: seals (of
wheel and swingarm bearings,
fork and brakes), electric com-
ponents (couplers, connec-
tors, instruments, switches
and lights), breather hoses
and vents.8For motorcycles equipped
with a windshield: Do not use
strong cleaners or hard
sponges as they will cause
dulling or scratching. Some
cleaning compounds for plas-
tic may leave scratches on the
windshield. Test the product
on a small hidden part of the
windshield to make sure that it
does not leave any marks. If
the windshield is scratched,
use a quality plastic polishing
compound after washing.
After normal useRemove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottle-
brush for hard-to-reach areas.
Stubborn dirt and insects will come
off more easily if the area is covered
with a wet cloth for a few minutes
before cleaning.After riding in the rain, near the sea
or on salt-sprayed roadsSince sea salt or salt sprayed on
roads during winter are extremely
corrosive in combination with water,
carry out the following steps after
each ride in the rain, near the sea or
on salt-sprayed roads.NOTE:
Salt sprayed on roads in the winter
may remain well into spring.1.Clean the motorcycle with cold
water and a mild detergent, after
the engine has cooled down.
ECA00012
cCDo not use warm water since it
increases the corrosive action of
the salt.2.Apply a corrosion protection
spray on all metal, including
chrome- and nickel-plated, sur-
faces to prevent corrosion.
MOTORCYCLE CARE AND STORAGE
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 80
SPECIFICATIONS
1
2
3
4
5
6
78
9
Wheels
Front
TypeCast
Size18 ´MT2.15
Rear
TypeCast
Size17 ´MT2.50
Brakes
Front
TypeSingle disc brake
OperationRight hand
FluidDOT 4
Rear
TypeSingle disc brake
OperationRight foot
FluidDOT 4
Suspension
Front
TypeTelescopic fork
Rear
TypeSwingarm (Monocross)Spring/shock absorber
Front
TypeCoil spring / oil damper
Rear
TypeCoil-gas spring / oil damper
Wheel travel
Front180 mm
Rear180 mm
Electrical
Ignition systemC.D.I.
Charging system
TypeC.D.I. magneto
Standard output14 V, 12A @5,000 r/min
Battery
TypeYTX5L-BS
Voltage, capacity12 V, 4 AH
Headlight typeQuartz bulb (halogen)
Bulb voltage, wattage ´quantity
Headlight12 V, 60/55W ´2
12 V, 35/35W ´2 (GB, IRL)
8-3
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 86
SPECIFICATIONS
1
2
3
4
5
6
78
9
8-4 Tail/brake light12 V, 5/21W ´2
Front turn signal light12 V, 21W ´2
Rear turn signal light12 V, 21W ´2
Auxiliary light12 V, 4W ´2
12 V, 3.4W ´2 (GB, IRL)
Meter lighting12 V, 3.4W ´3
Neutral indicator light12 V, 3.4W ´1
High beam indicator light12 V, 3.4W ´1
Oil level warning light12 V, 3.4W ´1
Turn indicator light12 V, 3.4W ´1
Fuse20A
5AE-9-E4 (ENG) 8/30/00 5:04 PM Page 87
