light YAMAHA TMAX 2020 Owner's Manual

Instrument and control functions
5-11
5
Instantaneous fuel consumption:
The instantaneous fuel consumption
mode “CRNT.F” can be set to “km/L”
or “L/100km”. For UK-spec vehicles:
“MPG”. (See page 5-14.)TIPIf traveling at speeds under 10 km/h (6
mi/h), “– –.–” will be displayed.NOTICE
ECA15474
If there is a malfunction, “– –.–” will
b
e continuously d isplayed. Have a
Yamaha dealer check the vehicle.
Settin g mo de
Stop the vehicle and then push the
“MENU” switch for 2 seconds to enter
the setting mode. To exit the setting
mode and return to the standard dis-
play mode, push the “MENU” switch
again for 2 seconds or
select “ ”.TIPWhen the malfunction indicator light is
on, setting mode cannot be entered.Menu items1. Setting mode display
Categ ory Description
This function allows you to
set the low, middle, and
high settings to 10 tem-
perature levels.
1
Grip Warmer
This function allows you to
set the low, middle, and
high settings to 10 tem-
perature levels.
This function allows you to
turn the traction control
system on or off.
This function allows you to
check and reset the oil
change interval (indicator),
V-Belt change interval (in-
dicator), and the “FREE”
maintenance interval.
This function allows you to
switch the fuel consump-
tion units between
“L/100km” and “km/L”.
For UK-spec vehicles: this
function is not available.
This function allows you to
change the items shown in
3 information displays.
This function allows you to
adjust the brightness of
the instrument panel.
This function allows you to
set the clock.
This function allows you to
reset all items to their fac-
tory preset or default set-
tings; excepting the
odometer, clock, and
maintenance counter
items “Oil” and “V-Belt”.
Seat HeaterTraction ControlMaintenance
UnitDisplayBrightnessCloc
k
All Reset
UB3TE0E0.book Page 11 Tuesday, September 17, 2019 9:35 AM

Instrument and control functions
5-12
5 Grip warmer settings
1. Use the select switch to highlight
“Grip Warmer”.
2. Push the “MENU” switch. The grip warmer setting display will be
shown.
3. Push the “MENU” switch. The temperature level for the high set-
ting will be highlighted. Use the select switch to set the
temperature level, and then push
the “MENU” switch.
4. Use the select switch to highlight “Mid” or “Low”, and then change
the setting using the same proce-
dure that was used for the high
setting.
5. When you finished changing the settings, use the select switch to
highlight “ ”, and then push the
“MENU” switch to return to the
menu screen.
Seat heater settings
1. Use the select switch to highlight “Seat Heater”. 2. Push the “MENU” switch. The
seat heater setting display will be
shown.
3. Push the “MENU” switch. The temperature level for the high set-
ting will be highlighted.
Use the select switch to set the
temperature level, and then push
the “MENU” switch.
UB3TE0E0.book Page 12 Tuesday, September 17, 2019 9:35 AM

Instrument and control functions
5-13
5
4. Use the select switch to highlight
“Mid” or “Low”, and then change
the setting using the same proce-
dure that was used for the high
setting.
5. When you finished changing the settings, use the select switch to
highlight “ ”, and then push the
“MENU” switch to return to the
menu screen.
Traction control system settings
1. Use the select switch to highlight “Traction Control”. 2. Push the “MENU” switch. The
traction control system setting
display will be shown.
3. To set the traction control system to “OFF”, push the select
switch “ ” side for 2 seconds. 4. To set the traction control system
to “ON” again, push the select
switch “ ”.
TIPWhen the vehicle is powered on, the
traction control system is automatically
set to “ON”.5. When you finished changing thesettings, push the “MENU” switch
to return to the menu screen.
Resettin g the maintenance counters
1. Use the select switch to highlight “Maintenance”.
UB3TE0E0.book Page 13 Tuesday, September 17, 2019 9:35 AM

Instrument and control functions
5-14
5
2. Push the “MENU” switch, and
then use the select switch to se-
lect the item to reset.
3. Push the “MENU” switch, and af- ter the selected item is highlight-
ed, push the select switch “ ”
for one second. 4. When you finished resetting, use
the select switch to highlight “ ”,
and then push the “MENU” switch
to return to the menu screen.
Selectin g the units
TIPU.K. specification vehicles only: This
function does not indicate on setting
mode display and cannot be selected.1. Use the select switch to highlight
“Unit”. 2. Push the “MENU” switch. The unit
setting display will be shown.
3. Use the select switch to select “L/100km” or “km/L”.
UB3TE0E0.book Page 14 Tuesday, September 17, 2019 9:35 AM

Instrument and control functions
5-15
5
4. Push the “MENU” switch to make
the selection and return to the
menu screen.
Selectin g the d isplay items
1. Use the select switch to highlight “Display Change”. 2. Push the “MENU” switch, use the
select switch to highlight the dis-
play to change, and then push the
“MENU” switch again.
3. Use the select switch to highlight the item to change, and then push
the “MENU” switch.
TIPDisplay item order is as follows.4. Use the select switch to select theitem to show, and then push the
“MENU” switch.A.TEMP TRIP-1 TRIP-2
ODO
CRNT.F F.AVG RANGE
UB3TE0E0.book Page 15 Tuesday, September 17, 2019 9:35 AM

Instrument and control functions
5-16
5 5. When you finished changing the
settings, use the select switch to
highlight “ ”, and then push the
“MENU” switch to return to the
previous display.
6. Use the select switch to highlight “ ”, and then push the
“MENU” switch to return to the
menu screen.
Meter panel brightness
1. Use the select switch to highlight “Brightness”.
2. Push the “MENU” switch.
3. Use the select switch to select the desired brightness level. 4. Push the “MENU” switch to return
to the menu screen.
Setting the clock
TIPThe clock uses a 12-hour time system.1. Use the select switch to highlight “Clock”. 2. Push the “MENU” switch.
3. When the hour digits are highlight-
ed, use the select switch to set the
hours.
4. Push the “MENU” switch, and the minute digits are highlighted.
5. Use the select switch to set the minutes.
UB3TE0E0.book Page 16 Tuesday, September 17, 2019 9:35 AM

Instrument and control functions
5-17
5
6. Push the “MENU” switch to return
to the menu screen.
Resetting all of the display items
1. Use the select switch to highlight “All Reset”.
2. Push the “MENU” switch.
3. Use the select switch to highlight “YES”, and then push the “MENU”
switch. All items are reset to facto-
ry preset or default settings.
TIPThe odometer, clock, maintenance
counter item “Oil” and maintenance
counter item “V-Belt” will not be reset.To exit the setting mode1. Use the select switch to highlight“Return”. 2. Push the “MENU” switch to exit
the setting mode and return to the
standard display mode.
UB3TE0E0.book Page 17 Tuesday, September 17, 2019 9:35 AM

Instrument and control functions
5-19
5
TIPBe sure to check that the rear wheel
does not move when the rear brake
lock lever is applied.
WARNING
EWA12362
Never move the rear brake lock lever
to the left while the vehicle is mov-
in g, otherwise loss of control or an
acci dent may result. Make sure that
the vehicle is stoppe d b efore mov-
in g the rear brake lock lever to the
left.
EAU65582
Anti-lock brake system (ABS)This model’s ABS features a dual elec-
tronic control system, which acts on
the front and rear brakes independent-
ly.
Operate the brakes with ABS as you
would conventional brakes. If the ABS
is activated, a pulsating sensation may
be felt at the brake levers. In this situa-
tion, continue to apply the brakes and
let the ABS work; do not “pump” the
brakes as this will reduce braking ef-
fectiveness.
WARNING
EWA16051
Always keep a sufficient d istance
from the vehicle ahea d to match the
ri din g speed even with ABS.
 The ABS performs best with
lon g b rakin g d istances.
 On certain surfaces, such as
rou gh or g ravel roa ds, the b rak-
in g d istance may be lon ger with
the ABS than without.The ABS is monitored by an ECU,
which will revert the system to conven-
tional braking if a malfunction occurs.
TIP The ABS performs a self-diagno-
sis test each time the vehicle is
turned on and travels at a speed of
10 km/h (6 mi/h) or higher. During
this test, a clicking noise can be
heard and if either brake lever is
even slightly applied, a vibration
can be felt at the lever, but this
does not indicate a malfunction.
 This ABS has a test mode which
allows the owner to experience
the pulsation at the brake levers
when the ABS is operating. How-
ever, special tools are required, so
please consult your Yamaha deal-
er.NOTICE
ECA20100
Be careful not to d amage the wheel
sensor or wheel sensor rotor; other-
wise, improper performance of the
ABS will result.
UB3TE0E0.book Page 19 Tuesday, September 17, 2019 9:35 AM

Instrument and control functions
5-21
5
EAU13222
FuelMake sure there is sufficient gasoline in
the tank.
WARNING
EWA10882
Gasoline an d gasoline vapors are
extremely flammab le. To avoid fires
an d explosions an d to re duce the
risk of injury when refuelin g, follow
these instructions.1. Before refueling, turn off the en- gine and be sure that no one is sit-
ting on the vehicle. Never refuel
while smoking, or while in the vi-
cinity of sparks, open flames, or
other sources of ignition such as
the pilot lights of water heaters
and clothes dryers.
2. Do not overfill the fuel tank. When refueling, be sure to insert the
pump nozzle into the fuel tank filler
hole. Stop filling when the fuel
reaches the bottom of the filler
tube. Because fuel expands when
it heats up, heat from the engine or
the sun can cause fuel to spill out
of the fuel tank. 3. Wipe up any spilled fuel immedi-
ately. NOTICE: Immediately
wipe off spille d fuel with a clean,
d ry, soft cloth, since fuel may
d eteriorate painte d surfaces or
plastic parts.
[ECA10072]
4. Be sure to securely close the fuel tank cap.
WARNING
EWA15152
Gasoline is poisonous an d can
cause injury or d eath. Handle gaso-
line with care. Never siphon gasoline
b y mouth. If you shoul d swallow
some gasoline or inhale a lot of gas-
oline vapor, or g et some gasoline in
your eyes, see your doctor imme di- ately. If g
asoline spills on your skin,
wash with soap an d water. If gaso-
line spills on your clothin g, chan ge
your clothes.
EAU86072
Your Yamaha engine was designed to
use unleaded gasoline with a research
octane number of 95 or higher. If en-
gine knocking or pinging occurs, use a
gasoline of a different brand or higher
octane rating.
1. Maximum fuel level
2. Fuel tank filler tube
1 2
Recommen
ded fuel:
Unleaded gasoline (E10 acceptable)
Octane num ber (RON):
95
Fuel tank capacity: 15 L (4.0 US gal, 3.3 Imp.gal)
Fuel tank reserve:
3.0 L (0.79 US gal, 0.66 Imp.gal)
UB3TE0E0.book Page 21 Tuesday, September 17, 2019 9:35 AM

Instrument and control functions
5-30
5
EAU63612
Ig nition circuit cut-off systemThe ignition circuit cut-off system
(comprising the sidestand switch and
brake light switches) has the following
functions.
 It prevents starting when the side-
stand is up, but neither brake is
applied.
 It prevents starting when either
brake is applied, but the sidestand
is still down.
 It cuts the running engine when
the sidestand is moved down.
Periodically check the operation of the
ignition circuit cut-off system accord-
ing to the following procedure.UB3TE0E0.book Page 30 Tuesday, September 17, 2019 9:35 AM