ABS YAMAHA TRACER 900 2017 User Guide
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2017, Model line: TRACER 900, Model: YAMAHA TRACER 900 2017Pages: 114, PDF Size: 5.27 MB
Page 85 of 114

Periodic maintenance and adjustment6-24
1
2
3
4
567
8
9
10
11
12
may deteriorate, causing leak-
age.
Refill with the same type of
brake fluid. Adding a brake fluid
other than DOT 4 may result in a
harmful chemical reaction.
Be careful that water or dust
does not enter the brake fluid
reservoir when refilling. Water
will significantly lower the boil-
ing point of the fluid and may re-
sult in vapor lock, and dirt may
clog the ABS hydraulic unitvalves.
NOTICE
ECA17641
Brake fluid may damage painted sur-
faces or plastic parts. Always cleanup spilled fluid immediately.
As the brake pads wear, it is normal for
the brake fluid level to gradually go
down. A low brake fluid level may indi-
cate worn brake pads and/or brake sys-
tem leakage; therefore, be sure to
check the brake pads for wear and the
brake system for leakage. If the brake
fluid level goes down suddenly, have a
Yamaha dealer check the cause before further riding.
EAU22733
Changing the brake fluidHave a Yamaha dealer change the
brake fluid at the intervals specified in
the periodic maintenance and lubrica-
tion chart. In addition, have the oil seals
of the master cylinders and calipers as
well as the brake hoses replaced at the
intervals listed below or whenever they
are damaged or leaking.
Oil seals: Replace every two
years.
Brake hoses: Replace every four
years.
2PP-9-E3.book 24 ページ 2016年9月13日 火曜日 午前9時7分
Page 94 of 114

Periodic maintenance and adjustment
6-33
1
2
3
4
56
7
8
9
10
11
12
EAU63131
Replacing the fusesThe fuse boxes and individual fuses are
located under the rider seat (See
page 3-28.) and behind panel A (See
page 6-9.).
To access fuse box 1, the main fuse,
and the fuel injection system fuse, re-
move the rider seat. (See page 3-28.)
TIPTo access the fuel injection system
fuse, remove the starter relay cover bypulling it upward. To access fuse box 2 and fuse box 3,
remove panel A. (See page 6-9.)
1. Fuse box 1
2. Main fuse
3. Fuel injection system fuse
4. Fuel injection system spare fuse1
3
4
2
1. Radiator fan motor fuse
2. Backup fuse (for clock and immobilizer system)
3. Electronic throttle valve fuse
4. ABS solenoid fuse
5. ABS motor fuse
6. Spare fuse
1
2
345
6
1. Starter relay cover
2. Fuel injection system fuse
3. Fuel injection system spare fuse
1. Fuse box 2
2. Fuse box 3
3
2
1
1
2
2PP-9-E3.book 33 ページ 2016年9月13日 火曜日 午前9時7分
Page 95 of 114

Periodic maintenance and adjustment6-34
1
2
3
4
567
8
9
10
11
12
If a fuse is blown, replace it as follows.
1. Turn the key to “OFF” and turn off the electrical circuit in question.
2. Remove the blown fuse, and then install a new fuse of the specified
amperage. WARNING! Do not
use a fuse of a higher amperage
rating than recommended to
avoid causing extensive dam- age to the electrical system and
possibly a fire.
[EWA15132]
1. Parking lighting fuse
2. Headlight fuse
3. Terminal fuse 2
4. Terminal fuse 1
5. Signaling system fuse
6. Auxiliary fuse 1
7. ABS control unit fuse
8. Auxiliary fuse 2
9. Spare fuse
10.Ignition fuse
1234
1098765
Specified fuses:
Main fuse:50.0 A
Auxiliary fuse 1:
2.0 A
Auxiliary fuse 2: 2.0 A
Terminal fuse 1: 2.0 A
Terminal fuse 2:
2.0 A
Headlight fuse: 7.5 A
Signaling system fuse: 7.5 A
Ignition fuse:
15.0 A
Parking lighting fuse: 7.5 A
Radiator fan motor fuse: 15.0 A
ABS motor fuse:
30.0 A
Fuel injection system fuse: 20.0 A
ABS solenoid fuse: 15.0 A
ABS control unit fuse: 7.5 A
Backup fuse: 7.5 A
Electronic throttle valve fuse:
7.5 A
2PP-9-E3.book 34 ページ 2016年9月13日 火曜日 午前9時7分
Page 104 of 114

Motorcycle care and storage
7-3
1
2
3
4
5
67
8
9
10
11
12 After cleaning
1. Dry the motorcycle with a chamois or an absorbing cloth.
2. Immediately dry the drive chain and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine chrome, aluminum and stain-
less-steel parts, including the ex-
haust system. (Even the thermally
induced discoloring of stain-
less-steel exhaust systems can be
removed through polishing.)
4. To prevent corrosion, it is recom- mended to apply a corrosion pro-
tection spray on all metal,
including chrome- and nickel-plat-
ed, surfaces.
5. Use spray oil as a universal clean- er to remove any remaining dirt.
6. Touch up minor paint damage caused by stones, etc.
7. Wax all painted surfaces.
8. Let the motorcycle dry completely before storing or covering it.
WARNING
EWA11132
Contaminants on the brakes or tires
can cause loss of control.
Make sure that there is no oil or
wax on the brakes or tires.
If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or ac-
etone, and wash the tires with
warm water and a mild deter-
gent. Before riding at higher
speeds, test the motorcycle’s
braking performance and cor-nering behavior.
NOTICE
ECA10801
Apply spray oil and wax spar-
ingly and make sure to wipe off
any excess.
Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.
Avoid using abrasive polishing
compounds as they will wearaway the paint.
TIP
Consult a Yamaha dealer for ad-
vice on what products to use.
Washing, rainy weather or humid climates can cause the headlight
lens to fog. Turning the headlight
on for a short period of time will
help remove the moisture from the
lens.
2PP-9-E3.book 3 ページ 2016年9月13日 火曜日 午前9時7分
Page 107 of 114

Specifications
8-2
1
2
3
4
5
6
789
10
11
12
6th: 1.037 (28/27)
Chassis:Frame type: Diamond
Caster angle: 24.0
Trail:
100 mm (3.9 in)Front tire:Type:Tubeless
Size:
120/70ZR17 M/C (58W)
Manufacturer/model: DUNLOP/D222FRear tire:Type:
Tubeless
Size: 180/55ZR17 M/C (73W)
Manufacturer/model: DUNLOP/D222Loading:Maximum load:180 kg (397 lb)
* (Total weight of rider, passenger, cargo and accessories)Tire air pressure (measured on cold
tires):1 person:Front:250 kPa (2.50 kgf/cm
2, 36 psi) Rear:
290 kPa (2.90 kgf/cm
2, 42 psi)
2 persons:
Front:250 kPa (2.50 kgf/cm2, 36 psi)
Rear:
290 kPa (2.90 kgf/cm2, 42 psi)
Front wheel:Wheel type: Cast wheel
Rim size:
17M/C x MT3.50Rear wheel:Wheel type:Cast wheel
Rim size:
17M/C x MT5.50Front brake:Type:Hydraulic dual disc brake
Specified brake fluid:
DOT 4Rear brake:Type:Hydraulic single disc brake
Specified brake fluid:
DOT 4Front suspension:Type:Telescopic fork
Spring:
Coil spring
Shock absorber: Hydraulic damper Wheel travel:
137 mm (5.4 in)
Rear suspension:Type:Swingarm (link suspension)
Spring: Coil spring
Shock absorber:
Gas-hydraulic damper
Wheel travel: 130 mm (5.1 in)Electrical system:System voltage:
12 V
Ignition system: TCI
Charging system: AC magnetoBattery:Model:YTZ10S
Voltage, capacity: 12 V, 8.6 Ah (10 HR)Bulb wattage:Headlight:LED
Brake/tail light: LED
Front turn signal light:
10.0 W
Rear turn signal light: 10.0 W
Auxiliary light: LED
2PP-9-E3.book 2 ページ 2016年9月13日 火曜日 午前9時7分
Page 108 of 114

Specifications
8-3
1
2
3
4
5
6
78
9
10
11
12
License plate light: 5.0 W
Meter lighting:
LED
Neutral indicator light: LED
High beam indicator light: LED
Oil level warning light:
LED
Turn signal indicator light: LED
Engine trouble warning light: LED
ABS warning light:
LED
Immobilizer system indicator light: LED
Traction control system indicator/warning
light: LEDFuse(s):Main fuse:
50.0 A
Auxiliary fuse 1: 2.0 A
Auxiliary fuse 2: 2.0 A
Terminal fuse 1:
2.0 A
Terminal fuse 2: 2.0 A
Headlight fuse: 7.5 A Signaling system fuse:
7.5 A
Ignition fuse:
15.0 A
Parking lighting fuse: 7.5 A
Radiator fan motor fuse: 15.0 A
Fuel injection system fuse:
20.0 A
ABS control unit fuse: 7.5 A
ABS motor fuse: 30.0 A
ABS solenoid fuse:
15.0 A
Backup fuse: 7.5 A
Electronic throttle valve fuse: 7.5 A
2PP-9-E3.book 3 ページ 2016年9月13日 火曜日 午前9時7分
Page 111 of 114

10-1
1
2
3
4
5
6
7
8
91011
12
Index
AABS ...................................................... 3-21
ABS warning light ................................... 3-4
Air filter element.................................... 6-17
Auxiliary DC connector ......................... 3-39
Auxiliary DC jack .................................. 3-39
Auxiliary lights....................................... 6-35BBattery .................................................. 6-31
Brake and clutch levers, checking and lubricating .................................... 6-28
Brake and shift pedals, checking and lubricating .................................... 6-28
Brake fluid, changing ............................ 6-24
Brake fluid level, checking .................... 6-23
Brake lever ........................................... 3-20
Brake lever free play, checking ............ 6-21
Brake light switches .............................. 6-22
Brake pedal .......................................... 3-21
Brake/tail light ....................................... 6-36CCables, checking and lubricating .......... 6-27
Canister ................................................ 6-11
Care ........................................................ 7-1
Catalytic converter ................................ 3-27
Centerstand and sidestand, checking and lubricating ..................... 6-29
Clutch lever........................................... 3-20
Clutch lever free play, adjusting ........... 6-21
Coolant ................................................. 6-14DData recording, vehicle ........................... 9-2
Diagnostic connecto r .............................. 9-2
Dimmer/Pass switch ............................. 3-18 D-mode (drive mode) ............................ 3-17
Drive chain, cleaning
and lubricating .... 6-26
Drive chain slack ................................... 6-25
EEngine break-in ....................................... 5-3
Engine idling speed, checking............... 6-17
Engine oil and oil filter cartridge ............ 6-11
Engine serial number ..............................9-1
Engine trouble warning light .................... 3-4FFront and rear brake pads, checking .... 6-22
Front fork, adjusting .............................. 3-33
Front fork, checking............................... 6-30
Fuel ....................................................... 3-25
Fuel consumption, tips for reducing ........5-3
Fuel tank cap......................................... 3-24
Fuel tank overflow hose ........................ 3-27
Fuses, replacing .................................... 6-33HHandlebar position, adjusting ................ 3-33
Handlebar switches ............................... 3-18
Hazard switch........................................ 3-19
Headlight beams, adjusting ................... 3-33
Headlights ............................................. 6-35
Helmet holder ........................................ 3-31
High beam indicator light .........................3-4
Horn switch ........................................... 3-19IIdentification numbers .............................9-1
Ignition circuit cut-off system ................. 3-37
Immobilizer system ................................. 3-1
Immobilizer system indicator light ........... 3-5
Indicator lights and warning lights ........... 3-4
LLicense plate light bul b, replacing......... 6-37
Luggage strap holders .......................... 3-36MMain switch/steering lock ........................ 3-2
Maintenance and lubrication, periodic .... 6-5
Maintenance, emission control system ... 6-3
Matte color, caution ................................ 7-1
Menu switch .......................................... 3-19
Model label ............................................. 9-2
Multi-function meter unit ......................... 3-6NNeutral indicator light .............................. 3-4OOil level warning light .............................. 3-4PPanel, removing and installing ................ 6-9
Parking.................................................... 5-4
Part locations .......................................... 2-1RRider seat height, adjusting .................. 3-29SSafety information ................................... 1-1
Seats..................................................... 3-28
Select switch ......................................... 3-19
Shifting .................................................... 5-2
Shift pedal ............................................. 3-20
Shock absorber assembly, adjusting .... 3-35
Sidestand .............................................. 3-37
Spark plugs, checking ........................... 6-10
Specifications.......................................... 8-1
Starting the engine.................................. 5-1
Steering, checking ................................ 6-31
Stop/Run/Start switch ........................... 3-19
2PP-9-E3.book 1 ページ 2016年9月13日 火曜日 午前9時7分