ignition YAMAHA TT600RE 2004 User Guide

ELECTRICAL CIRCUIT DIAGRAM
7-2
ELEC
B Black B/Y Black/Yellow
Br Brown Br/B Brown/Black
Ch Chocolate Br/W Brown/White
Dg Deep green G/B Green/Black
G Green G/R Green/Red
Gy Grey G/W Green/White
L Blue G/Y Green/Yellow
Or Orange L/R Blue/Red
P Pink L/W Blue/White
R Red L/Y Blue/Yellow
Sb Sky-blue R/B Red/Black
W White R/W Red/White
Y Yellow R/Y Red/Yellow
B/R Black/Red W/L White/Blue
B/W Black/White Y/R Yellow/Red
(1) AC generator/Pickup coil
(2) Rectifier/Regulator
(3) Battery
(4) Starter relay
(5) Starting motor
(6) Fuse
(7) Main switch
(8) Right handlebar switch
(9) Engine stop switch
(10) Starter switch
(11) Diode
(12) Clutch switch
(13) Sidestand switch
(14) Neutral switch
(15) Diode
(16) Ignitor unit
COLOUR CODE (17) Ignition coil
(18) Left handlebar switch
(19) Horn switch
(20) Diode
(21) Pass switch
(22) Dimmer switch
(23) Flasher switch
(24) Horn
(25) Flasher relay
(26) Headlight
(27) Flasher light
(28) Relay assy
(29) Front brake switch
(30) Rear brake switch
(31) Tail/stop light
(32) Meter
ProCarManuals.com

ELECELECTRICAL COMPONENTS
7-3
ELECTRICAL COMPONENTS
(1) Main wire harness
(2) Diodes
(3) Extension wire harness
(4) Rectifier/Regulator
(5) CDI ignition unit
(6) Battery (12V – 8Ah)
(7) Starter relay
(8) Fuse (20A) BATTERY: CAPACITY 12V – 8Ah
SPECIFIC GRAVITY: 1.320
ProCarManuals.com

ELECTRICAL COMPONENTS
7-4
ELEC
IGNITION COIL: Primary winding resistance: 4 Ω
Ω
± 15% at 20°C (68°F)
Secondary winding resistance: 13 k Ω
Ω
± 20% at 20°C (68°F)(1) Ignition coil
(2) Spark plug cap
(3) Flasher relay
(4) Horn
(5) Clutch switch
(6) Relay assy
(7) Sidestand switch
(8) Neutral switch
(9) Main switch
ProCarManuals.com

ELECIGNITION SYSTEM
7-11
467C4B5CAMP403D494A4856 172320-2
GWLY
BB
B
BBLWRB
R
B
B
B
RLBOrRBLYGW
Or
B
LW
MAIN HARNESSB
B
B
Y Y
LBG
LGRBLYGWLWLBOrRB
LW
GY
GY
RBBr
Br187
GB
12V10W
BL12V5WBY G
12V60/55WBGYAA
12V10W
A
GB
BrBBrB
BGBB
GBBGBB
BrB
12V10WB
B
BrL
GB
12V10WB
B
187
BY
B
R
B
BrL
WWB
OFF
BrL
W
B
W
BB
B
B BLB
BBrB
G
B
BrB
Br
OFF
B
EXT. CORD
Br
GY
BL
G
Y
GYB
B
L
GB
BrB
LR
LR Sb
B
RW
-
LR
L
BrL
GBSbB
BrB
YBrBrB
YBrGB
B
Ch
DgBrY
BrB
HIGH
TURN
NEU.ILL.
B
BrL
BrL
LBBY
LY LB
LY
GWB
RBOr
205
B
RBL
BrL
Br
PARKOFFON
ON
ON
Sb
L
GB
GY

G
Y
RBLYBY
LYBY
RUN
LW
B
B
LY
BY
LBrRR
LWRB
GB
R
B
GW
BrBrW
WB
Br
LY
WB
Sb
B
GWLY
(BLUE)B
B
LYB
OFF
BrRB
LWRB
Y
P
G
GB BBrWBrL
BrB
W
WW
GYBr
GY
Y
P
G
GB B
BrWBrL
BrB
Y
N
RL
LOWHIGH
BrW Br
P
PBr
LY
B
GWLY
Or
RB
Br
LW
BY
BY
START
OFF
R
B
GWLY
W
W W
W
W
W
W
RW
W
W
Sb
B
Sb
BBrBB
-
-
B
LR
WRW
B
-
AL
L
GY
LB
Br
WB
RB
MAIN HARNESS
AHEAD LIGHT
B
B
BrB
17
16
11
12
13
14
15
91029
8
5
3
12
6428
20
21
22
19
2325
24
30
31
27
267
32
18
BrW
IGNITION SYSTEM -CIRCUIT DIAGRAM
ProCarManuals.com

IGNITION SYSTEM
7-12
ELEC
The diagram illustrates the ignition circuit inside the motorcycles electric system. NOTE:
For the colour code and legend, see page 7-2.
(1) AC generator/Pickup coil
(2) Rectifier/Regulator
(3) Battery
(6) Fuse
(7) Main switch
(9) Engine stop switch
(11) Diode (12) Clutch switch
(13) Sidestand switch
(14) Neutral switch
(15) Diode
(16) Ignitor unit
(17) Ignition coil

\f

\f\f
\f
\f
\f\f
\f\f
ProCarManuals.com

ELECIGNITION SYSTEM
7-13
DIAGNOSTICS IF THE IGNITION SYSTEM WERE TO STOP WORKING (NO OR INTERMITTENT SPARK)
Procedure
Check:
1. Fuse
2. Battery
3. Spark plug
4. Amplitude of ignition spark
5. Spark plug cap resistance
6. Ignition winding resistance 7. Main switch
8. Engine stop switch
9. Sidestand switch
10. Neutral switch
11. Clutch switch
12. Pick-up coil resistance
13. Wiring connections (whole connection sys- tem)
NOTE:
Before making the inspections mentioned, remove the following parts:
1. Seat
2. Rear cowling 3. Fuel tank
4. Cowling (headlight)
•To check functioning defects use the following special tools.
Dinamic spark tester: P/N. 90890-06754
Pocket tester:P/N. 90890-03112
1. Fuse
•Check the fuse for continuity.
Refer to “CHECKING THE FUSES” in
Chapter 3.
•Is the fuse OK?
YES
2. Battery
•Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in Chapter 3.
Min. open-circuit voltage:
2.8 V or more at 20°C (68°F)
•Is the battery OK?
NO
Replace the fuse.
NO
•Clean the battery terminals.
•Recharge or replace the battery.
YES
*
ProCarManuals.com

IGNITION SYSTEM
7-14
ELEC
3. Spark plug.
•Check the conditions of the spark plug.
•Check the type of spark plug used.
•Check the electrodes gap.
Standard spark plug: DPR8EA-9 (NGK), DPR9EA-9
4. Amplitude of the ignition spark.
•Detach the spark plug cap from the spark
plug.
•Connect the dynamic spark tester (1) as
shown in the figure.
(2) Spark plug cover (3) Spark plug
•Turn the main switch ON.
•Check the amplitude of the ignition spark.
•Start the engine and increase the ampli-
tude until the ignition becomes discontin-
uous.
Electrodes gap: DPR8EA-9, DPR9EA-9 (NGK)
0.8 ~ 0.9 mm
YES
OUT OF SPECIFICATION
Correct the electrodes gap or replace the spark
plug.
Spark amplitude if the ignition
system is efficient: 6.0 mm
THE IGNITION SYSTEM IS INEFFICIENT
OR THERE IS NO SPARK
IN COMPLIANCE WITH SPECIFICATIONS
Minimum spark amplitude.
*
*
ProCarManuals.com

ELECIGNITION SYSTEM
7-15
IN COMPLIANCE
WITH SPECIFICATIONS
5. Spark plug cap resistance.
•Remove the spark plug cap.
•Connect the pocket tester ( Ωx 1k) to the
spark plug cap.
•Check that the spark plug cap has the
specified resistance.
OUT OF SPECIFICATION
The spark plug cap is defective.
Replace.
Resistance of spark plug cap: 10 k Ωat 20°C (68°F)
6. Ignition winding resistance.
•Disconnect the ignition coil cables from
the wire harness.
•Connect the pocket tester ( Ωx 1) to the
ignition coil.
Tester terminal (+) ➔Pole (+)
Tester terminal (–) ➔Pole (–)
•Check that the primary coil has the speci-
fied resistance.
*
ProCarManuals.com

IGNITION SYSTEM
7-16
ELEC
•Connect the pocket tester ( Ωx 1) to the
ignition coil.
Tester terminal (+) ➔Spark plug cable (1)
Tester terminal (–) ➔Pole (+)
•Check that the secondary coil has the
specified resistance
Secondary winding resistance: 13 k Ω ±
±

20% at 20°C (68°F)
(Spark plug cable – Terminal (–))
BOTH RESISTANCE
VALUES ARE CORRECT
OUT OF SPECIFICATION
The ignition coil is defective.
Replace.
*
Primary winding resistance: 4 Ω ±
±
15% at 20°C (68°F)
(Terminal (+) – Terminal (–))
7. Main switch.
•Disconnect the main switch connector
from the wire harness.
•Connect the pocket tester ( Ωx 1) to the
main switch cables. Refer to “SWITCH CHECK” in Chapter 3.
CORRECT
INCORRECT
The main switch is defective. Replace.





 


  
ProCarManuals.com

ELECIGNITION SYSTEM
7-17
*
CORRECT
8. Emergency stop engine switch.
•Disconnect the emergency stop engine
switch connector (Brown, Green/Yellow
and Red/Black) from the wire harness.
•Connect the pocket tester ( Ωx 1) to the
switch cables. Refer to “SWITCH CHECK” in Chapter 3.
Tester terminal (+) ➔Red/Black (1) cable
Tester terminal (–) ➔Brown cable (2)
CORRECT
INCORRECT
The emergency stop engine switch is defective.
Replace the right handlebar switch.
INCORRECT
The sidestand switch is defective. Replace.
*
9. Sidestand switch.
•Disconnect the sidestand switch connec-
tor (Black and Black) from the wire har-
ness.
•Connect the pocket tester ( Ωx 1) to the
sidestand switch cables. Refer to “SWITCH CHECK” in Chapter 3.
Tester terminal (+) ➔Black cable (1)
Tester terminal (–) ➔Black cable (2)





 
 



\f









\f
ProCarManuals.com