fuel YAMAHA VERSITY 300 2004 User Guide

PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU03685
Periodic maintenance and lubrication chart
NOTE :
•The annual checks must be performed every year, except if a kilometer-based maintenance is performed instead.
•From 50,000 km, repeat the maintenance intervals starting from 10,000 km.
•Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools, data and technical
skills.
1 * Fuel line•Check fuel hoses and vacuum hose for cracks or damage.√√√√ √
•Check condition.
√√
2 Spark plug•Clean and regap.
•Replace.√√
3 * Valves•Check valve clearance.
√√
•Adjust.
4 Air filter element•Clean.√√•Replace.√√
5 V-belt case air filter element•Clean.√√√√
•Check operation, fluid level and vehicle for fluid leakage.
√√√√√ √
6 * Front brake(See NOTE on page 6-4.)
•Replace brake pads. Whenever worn to the limit
ODOMETER READING (x 1,000 km)
NO. ITEMCHECK OR MAINTENANCE JOB
1
ANNUAL
CHECK
10 20 30 40
6-2

PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU00637
Adjusting the valve clea-
rance
The valve clearance changes with use,
resulting in improper air-fuel mixture
and/or engine noise. To prevent this
from occurring, the valve clearance
must be adjusted by a Yamaha dealer
at the intervals specified in the periodic
maintenance and lubrication chart.
EAU04551*
Tires
To maximize the performance,
durability, and safe operation of your
scooter, note the following points
regarding the specified tires.
Tire air pressure
The tire air pressure should be checked
and, if necessary, adjusted before each
ride.
EW000082
•The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the temperature
of the tires equals the ambient
temperature).
•The tire air pressure must be
adjusted in accordance with the
riding speed and with the total
weight of rider, passenger,
cargo, and accessories
approved for this model.
WARNING
Maximum load* 202 k g
* Total weight of rider, passenger, cargo and
accessories
6-21
0 12
3
4
ZAUM0053
Tire air pressure
(measured on cold tires)
Load* Front Rear
Up to 90 kg*180 kPa
1.8 kgf/cm
2
1.8 bar190 kPa
1.9 kgf/cm
2
1.9 bar
90 kg ~ 160 kg load*
180 kPa
1.8 kgf/cm2
1.8 bar200 kPa
2.0 kgf/cm
2
2.0 bar
160 kg ~
maximum load*
190 kPa
1.9 kgf/cm2
1.9 bar220 kPa
2.2 kgf/cm
2
2.2 bar

PERIODIC MAINTENANCE AND MINOR REPAIR
6
1. Turn signal socket (x2)
2. Tail/brake socket (x2)
3. Remove the socket (together with
the bulb) by turning it
counterclockwise.
4. Remove the defective bulb by
pushing it in and turning it
counterclockwise.
5. Insert a new bulb into the socket,
push it in, and then turn it
clockwise until it stops.
6. Install the socket (together with
the bulb) by turning it clockwise.
7. Install the panel.
1. Bulb socket
2. Screw
EAUM0062
Replacing the license plate
light bulb
1. Remove the license plate light
cover by removing the screw.
2. Remove the socket (together with
the bulb) by pulling it out.
3. Remove the defective bulb by
pulling it out.
4. Insert a new bulb into the socket.
5. Install the socket (together with
the bulb) by pushing it in.
6. Install the license plate light cover
by installing the screw.
EAU03087
Troubleshooting
Although Yamaha scooters receive a
thorough inspection before shipment
from the factory, trouble may occur
during operation. Any problem in the
fuel, compression, or ignition systems,
for example, can cause poor starting
and loss of power.
The following troubleshooting charts
represent quick and easy procedures
for checking these vital systems
yourself. However, should your scoo-
ter require any repair, take it to a
Yamaha dealer, whose skilled
technicians have the necessary tools,
experience, and know-how to service
the scooter properly.
Use only genuine Yamaha replacement
parts. Imitation parts may look like
Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
6-35
21
ZAUM0467
1
2
ZAUM0586

PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU01581
Troubleshooting charts
Starting problems or poor engine performanceEW000125
Keep away open flames and do not smoke while checking or working on the fuel system.
WARNING
Check the fuel level in
the fuel tank.
1. FuelThere is enough fuel.
There is no fuel.Check the compression.
Supply fuel.
The engine does not start.
Check the compression.
Operate the electric starter.
2. CompressionThere is compression.
There is no compression.Check the ignition.
Have a Yamaha dealer
check the vehicle.
Remove the spark plug
and check the electrodes.
3. IgnitionWipe off with a dry cloth and correct the
spark plug gap, or replace the spark plug.
Have a Yamaha dealer check the vehicle.
The engine does not start.
Have a Yamaha dealer
check the vehicle.
The engine does not start.
Check the battery.
Operate the electric starter.
4. BatteryThe engine turns over
quickly.
The engine turns over
slowly.The battery is good.
Check the battery lead connections,
and charge the battery if necessary.
Dry
WetOpen the throttle halfway and operate
the electric starter.
6-36

SCOOTER CARE AND STORAGE
7
•Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
•Do not use high-pressure
washers or steam-jet cleaners
since they cause water
seepage and deterioration in
the following areas: seals (of
wheel and swingarm bearings,
fork and brakes), electric
components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.
•For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the
windshield. Test the product on
a small hidden part of the
windshield to make sure that it
does not leave any marks. If the
windshield is scratched, use a
quality plastic polishing
compound after washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea
or on salt-sprayed roads
Since sea salt or salt sprayed on the
roads during winter are extremely cor-
rosive in combination with water, carry
out the following steps after each ride
in the rain, near the sea or on salt-
sprayed roads.
NOTE :
Salt sprayed on roads in the winter may
remain well into spring.
1. Clean the scooter with cold water
and a mild detergent after the
engine has cooled down.
ECA00012
Do not use warm water since it
increases the corrosive action of the
salt.
2. Apply a corrosion protection spray
on all metal, including chrome-
and nickel-plated, surfaces to
prevent corrosion.
CAUTION:
7-2

SCOOTER CARE AND STORAGE
7 Long-term
Before storing your scooter for several
months:
1. Follow all the instructions in the
"Care" section of this chapter.
2. Drain the carburetor float chamber
by loosening the drain bolt; this will
prevent fuel deposits from building
up. Pour the drained fuel into the
fuel tank.
3. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
4. Perform the following steps to
protect the cylinder, piston rings,
etc. from corrosion.
a. Remove the spark plug cap and
spark plug.
b. Pour a teaspoonful of engine oil
into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit
sparking during the next step.)d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap from
the spark plug, and then install
the spark plug and the spark
plug cap.
EWA00003
To prevent damage or injury from
sparking, make sure to ground the
spark plug electrodes while turning
the engine over.
5. Lubricate all control cables and
the pivoting points of all levers and
pedals as well as of the sidestand/
centerstand.
6. Check and, if necessary, correct
the tire air pressure, and then lift
the scooter so that both of its
wheels are off the ground.
Alternatively, turn the wheels a
little every month in order to
prevent the tires from becoming
degraded in one spot.
WARNING
7. Cover the muffler outlet with a
plastic bag to prevent moisture
from entering it.
8. Remove the battery and fully
charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an
excessively cold or warm place
(less than 0 °C or more than 30
°C). For more information on
storing the battery, see page
6-30.
NOTE :
Make any necessary repairs before
storing the scooter.
7-4

SPECIFICATIONS
8
Model VP300
Dimensions:
Overall length 2,170 mm
Overall width 765 mm
Overall height 1,465 mm
Seat height 805 mm
Wheelbase 1,480 mm
Minimum ground clearance 155 mm
Minimum turning radius 1,706 mm
Weight:
Wet (with oil and a full fuel tank) 174 kg
Engine:
Engine type Liquid cooled, 4 strokes SOHC
Cylinder arrangementSingle cylinder, Forward inclined
Displacement 264 cm
3
Bore x stroke 71.0 x 66.8
Compression ratio 10:1
Starting system type Electric starter
Lubrication system Wet sump
Specifications
Engine oil:
Type
-20°-10°10°20°30°40°50°C
0°
SAE 10W/30
SAE 10W/40
SAE 15W/40
SAE 20W/40
SAE 20W/50
Recommended engine oil API Service SE, SF, SG type
Classification or higher
CAUTION:
8-1
Be sure to use motor oils that do not contain anti-fric-
tion modifiers. Passenger car motor oils (often labeled
“Energy Conserving II”) contain anti-friction additives
which will cause clutch and/or starter cluth slippage,
resulting in reduced component life and poor engine
performance.
Quantity
Periodic oil change 1.2 L
Total amount (dry engine) 1.4 L

SPECIFICATIONS
8
Transmission oil:
Type Engine oil SAE 10W30
(API SE)
Total amount 0.25L
Coolant system capacity:
(including all routes)1.6L
Air filter:Wet type element.
Fuel:
Recommended fuel REGULAR UNLEADED
GASOLINE ONLY
Fuel tank capacity 10.9L
Carburetor:
Type / quantity TK5SE x 1
Manufacturer TK
Spark plug:
Type / Manufacturer DR8EA / NGK
Spark plug gap 0.6—0.7 mm
Clutch type:Dry, centrifugal automatic
Transmission:
Primary reduction system Helical gear
Primary reduction ratio 40/15 (2.666)
Secondary reduction system Helical gear
Secondary reduction ratio 37/12 (3.083)
Transmission type V-belt automatic
Operation Centrifugal automatic typeChassis:
Frame type Steel tube underbone
Caster angle ((degree)) 26°
Trail 90 mm
Tires:
Front:
Type Tubeless
Size 120/80-14 58P
Manufacturer / Model MICHELIN / PILOT CITY TL
Rear:
Type Tubeless
Size 150/70-14 66P
Manufacturer / Model MICHELIN / PILOT CITY TL
Maximum load * 202 Kg
Air pressure (cold tire):
Up to 90 kg load*
Front 180 kpa (1.8 kgf/cm
2, 1.8 Bar)
Rear 190 kpa (1.9 kgf/cm2, 1.9 Bar)
90 kg load — 160 kg load *
Front 180 kpa (1.8 kgf/cm
2, 1.8 Bar)
Rear 200 kpa (2.0 kgf/cm2, 2.0 Bar)
160 kg load — maximum
load *
Front 190 kpa (1.9 kgf/cm
2, 1.9 Bar)
Rear 220 kpa (2.2 kgf/cm2, 2.2 Bar)
* Total weight of rider, passenger, cargo and accessories.
8-2

INDEX
A
Acceleration and deceleration ............. 5-3
Air filter and V-belt case air filter
elements, cleaning ....................... 6-18
Anti-theft alarm (optional) ................... 3-7
Auxiliary DC jack ............................... 3-18
Anti-theft device housing ................... 3-14
B
Battery .............................................. 6-29
Battery voltage / coolant
temperature gauge ......................... 3-3
Brake fuid level, checking ................. 6-24
Brake fluid, changing ........................ 6-25
Bake lever, front .................................. 3-9
Brake lever, rear .................................. 3-9
Brake levers, lubricating .................... 6-26
Brake pads, checking ........................ 6-24Braking ................................................ 5-3
C
Cables, checking and lubricating ...... 6-26
Carburator, adjusting ......................... 6-20
Care .................................................... 7-1
Catalytic converter ............................ 3-11
Centerstand and sidestand, checking
and lubricating .............................. 6-27
Conversion table ................................. 8-4
Coolant .............................................. 6-17
Cowlings and panels, removing
and installing .................................. 6-5
E
Engine break-in ................................... 5-4
Engine oil .......................................... 6-13
F
Final transmission oil ........................ 6-16
Front and rear brake lever free play,
adjusting ....................................... 6-23
Front fork, checking ........................... 6-27
Fuel ................................................... 3-10
Fuel consumption, tips for reducing .... 5-4
Fuel gauge .......................................... 3-3
Fuel tank cap .................................... 3-10Fuses, replacing ................................ 6-30
H
Handlebar switches ............................. 3-8
Dimmer switch ............................... 3-8
Engine stop switch ......................... 3-8
Horn switch .................................... 3-8
Hazard switch ................................ 3-9
Pass switch .................................... 3-8
Start switch .................................... 3-8
Turn signal switch ........................... 3-8
Headlight bulb, replacing ................... 6-32
I
Identification number ........................... 9-1
Ignition circuit cut-off system ............. 3-16
Indicator lights ..................................... 3-2
High beam indicator light ............... 3-2
Low beam indicator light ................ 3-2
Turn signal indicator lights .............. 3-2
K
Key identification number .................... 9-1
L
License plate liht bulb, replacing ....... 6-35