oil pressure YAMAHA VMAX 2009 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2009, Model line: VMAX, Model: YAMAHA VMAX 2009Pages: 102, PDF Size: 2.56 MB
Page 53 of 102
PERIODIC MAINTENANCE AND ADJUSTMENT
6-3
2
3
4
5
67
8
9
9*
Wheels
Check runout and for damage.
√√√√
10
*
Tires
Check tread depth and for dam-
age.
Replace if necessary.
Check air pressure.
Correct if necessary.
√√√√√
11
*
Wheel bearings
Check bearing for looseness or
damage.
√√√√
12
*
Swingarm
Check operation and for exces-
sive play.
√√√√
Lubricate with lith-
ium-soap-based grease.Every 50000 km (30000 mi)
13
*
Steering bearings
Check bearing play and steering
for roughness.
√√√√√
Lubricate with lith-
ium-soap-based grease.Every 50000 km (30000 mi)
14
Brake lever pivot
shaft
Lubricate with silicone grease.
√√√√√
15
Brake pedal pivot
shaft
Lubricate with lith-
ium-soap-based grease.
√√√√√
16
Clutch lever pivot
shaft
Lubricate with silicone grease.
√√√√√
17
Shift pedal pivot
shaft
Lubricate with lith-
ium-soap-based grease.
√√√√√
18
Sidestand
Check operation.
Lubricate.
√√√√√
19
*
Sidestand switch
Check operation.
√√√√√√
20
*
Front fork
Check operation and for oil leak-
age.
√√√√
NO. ITEM CHECK OR MAINTENANCE JOBODOMETER READING
ANNUAL
CHECK 1000 km
(600 mi)10000 km
(6000 mi)20000 km
(12000 mi)30000 km
(18000 mi)40000 km
(24000 mi)
Page 93 of 102
MOTORCYCLE CARE AND STORAGE
7-4
2
3
4
5
6
78
9
EAU26242
Storage
Short-term
Always store your motorcycle in a cool,
dry place and, if necessary, protect it
against dust with a porous cover.
NOTICE
ECA10810
Storing the motorcycle in a
poorly ventilated room or cover-
ing it with a tarp, while it is still
wet, will allow water and humid-
ity to seep in and cause rust.
To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-
cals are stored.
Long-term
Before storing your motorcycle for sev-
eral months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and thefuel from deteriorating.
3. Perform the following steps to pro-
tect the cylinders, piston rings, etc.
from corrosion.
a. Remove the spark plug caps
and spark plugs.
b. Pour a teaspoonful of engine oil
into each spark plug bore.
c. Install the spark plug caps onto
the spark plugs, and then place
the spark plugs on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder walls with oil.)
WARNING! To prevent dam-
age or injury from sparking,
make sure to ground the
spark plug electrodes while
turning the engine
over.
[EWA10951]
e. Remove the spark plug caps
from the spark plugs, and then
install the spark plugs and the
spark plug caps.
4. Lubricate all control cables and thepivoting points of all levers and
pedals as well as of the sidestand/
centerstand.
5. Check and, if necessary, correct
the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
6. Cover the muffler outlets with plas-
tic bags to prevent moisture from
entering them.
7. Remove the battery and fully
charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an ex-
cessively cold or warm place [less
than 0 °C (30 °F) or more than 30
°C (90 °F)]. For more information
on storing the battery, see page
6-28.
TIP
Make any necessary repairs before
storing the motorcycle.