remote control YAMAHA VX110 2005 Owner's Manual

7-61
E
–+ELEC
REMOTE CONTROL SYSTEM
(DELUXE MODEL ONLY)
NOTE:
If the start switch or the remote control
transmitter is not operated for more than
25 seconds, the multifunction meter dis-
play and the “L-MODE” indicator light will
go off. To change the modes again, press
the lock button for a short time, and then
start the procedures from the lock mode.
While the engine is running, input is not
received from the remote control transmit-
ter.
ProCarManuals.com

7-62
E
–+ELEC
REMOTE CONTROL SYSTEM
(DELUXE MODEL ONLY)
Transmitter registration
1. Register:
Remote control transmitter 1
ID codes can be added or re-registered
by connecting the entry box 2.
Registration steps:
Connect the entry box.
Transmit the ID code from the remote
control transmitter to be registered.
NOTE:
The remote control transmitters can be reg-
istered in any sequence, regardless of
whether they are original equipment or
additional transmitters.
At this time, the system enters the regis-
tration mode to register the first code. All
existing ID codes will be deleted from the
EEPROM.
The “SECURITY” indicator light flashes
when the registration of the ID code has
been completed. (If the registration could
not be completed, the “SECURITY” indi-
cator light comes on. Re-transmit the ID
code.)
After confirming that the registration of
the ID code has been completed using
the “SECURITY” indicator light, transmit
the next ID code.
Register the ID codes for up to five
remote control transmitters.
After ID code registration has been com-
pleted, disconnect the entry box to exit
the registration mode.
Gy
B
12
ProCarManuals.com

7-63
E
–+ELEC
REMOTE CONTROL SYSTEM
(DELUXE MODEL ONLY)
Replacing of the transmitter battery
CAUTION:
Do not allow any water, dust, or dirt to
enter the remote control transmitter case
when replacing the battery.
Make sure that no foreign material is
trapped between the upper case and
lower case of the remote control transmit-
ter during assembly.
1. Remove:
Cover
NOTE:
Loosen the transmitter cover screws in the
sequence shown.
4
1
532 6
2. Install:
Battery 1
NOTE:
Install the battery (CR2016) with the positive
side facing down.
1
3. Install:
Cover
NOTE:
Tighten the transmitter cover screws in the
sequence shown.
T R..
Transmitter cover screw:
0.1 N  m
(0.01 kgf  m, 0.1 ft  lb)
3
6
245 1
ProCarManuals.com

E
HULL
HOOD
1
2
3
4
5
6
7
8
9
REMOTE CONTROL CABLES AND SPEED SENSOR LEAD .................... 8-23
EXPLODED DIAGRAM ........................................................................... 8-23
REMOVAL AND INSTALLATION CHART .............................................. 8-23
SERVICE POINTS .................................................................................. 8-26
Remote control cables inspection ..................................................... 8-26
Steering cable (jet pump end) installation ......................................... 8-26
Steering cable stopper installation .................................................... 8-26
Shift cable (jet pump end) installation (Deluxe model only) .............. 8-27
Shift cable (shift lever end) installation (Deluxe model only)............. 8-27
Remote control cables adjustment .................................................... 8-27
SEAT AND HAND GRIP................................................................................ 8-28
EXPLODED DIAGRAM ........................................................................... 8-28
REMOVAL AND INSTALLATION CHART .............................................. 8-28
SERVICE POINTS .................................................................................. 8-30
Seat lock assembly inspection .......................................................... 8-30
EXHAUST SYSTEM ...................................................................................... 8-31
EXPLODED DIAGRAM ........................................................................... 8-31
REMOVAL AND INSTALLATION CHART .............................................. 8-31
SERVICE POINTS .................................................................................. 8-34
Exhaust system inspection................................................................ 8-34
Exhaust component parts sub-assembly .......................................... 8-34
Exhaust system installation ............................................................... 8-35
DECK AND HULL.......................................................................................... 8-36
EXPLODED DIAGRAM ........................................................................... 8-36
REMOVAL AND INSTALLATION CHART .............................................. 8-36
ENGINE MOUNT ........................................................................................... 8-38
EXPLODED DIAGRAM ........................................................................... 8-38
REMOVAL AND INSTALLATION CHART .............................................. 8-38
ProCarManuals.com

8-16
E
HULL
HOODSHIFT LEVER (DELUXE MODEL ONLY)
SHIFT LEVER (DELUXE MODEL ONLY)
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step Procedure/Part name Q’ty Service points
SHIFT LEVER REMOVAL
Follow the left “Step” for removal.
Engine hatch cover Refer to “ENGINE HATCH COVER”.
Shift cable Refer to “REMOTE CONTROL CABLES
AND SPEED SENSOR LEAD”.
1Bolt 2
2 Detent plate 1
3 Shift lever 1
4Nut 2
5Bracket 1
Reverse the removal steps for installation.
5 43
21
6 × 18 mm
8.0 N • m (0.8 kgf • m, 5.8 ft • Ib)
4
1
LT
572
LT
LT
572
LT
15 N • m (1.5 kgf • m, 11 ft • Ib)
ProCarManuals.com

8-20
E
HULL
HOODSTEERING COLUMN
STEERING COLUMN
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step Procedure/Part name Q’ty Service points
STEERING COLUMN REMOVAL
Follow the left “Step” for removal.
Engine hatch cover Refer to “ENGINE HATCH COVER”.
Steering cable end Refer to “REMOTE CONTROL CABLES
AND SPEED SENSOR LEAD”.
1Bolt 1
2 Steering arm 1
3 Joint ball 1
4Bolt 4
5 Steering column assembly 1
Reverse the removal steps for installation.
5
4
2
3 1
6.9 N • m (0.69 kgf  m, 5.0 ft  Ib)
8 × 30 mm
17 N  m (1.7 kgf  m, 12 ft  Ib)
LT
572
LT
LT
242
LT
8 × 18 mm
20 N  m (2.0 kgf  m, 14 ft  Ib)
ProCarManuals.com

8-23
E
HULL
HOOD
REMOTE CONTROL CABLES AND
SPEED SENSOR LEAD
REMOTE CONTROL CABLES AND SPEED SENSOR LEAD
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step Procedure/Part name Q’ty Service points
REMOTE CONTROL CABLES
AND SPEED SENSOR LEAD
REMOVALFollow the left “Step” for removal.
Service lid 1 Refer to “FRONT HOOD”.
Seat assembly Refer to “SEAT AND HAND GRIP”.
Engine hatch cover Refer to “ENGINE HATCH COVER”.
Shift lever Refer to “SHIFT LEVER (DELUXE MODEL
ONLY)”.
1 Steering cable end 1
2Bolt 1
3Bracket 1
ProCarManuals.com

8-24
E
HULL
HOOD
REMOTE CONTROL CABLES AND
SPEED SENSOR LEAD
EXPLODED DIAGRAM
Step Procedure/Part name Q’ty Service points
4Nut 1
5 Steering cable 1
6 Seal 1
7 Speed sensor coupler 1
8Nut 1
9Cap 1
10 Screw 4
11 Speed sensor 1
12 Bolt 2 Deluxe model only
13 Shift cable holder 1 Deluxe model only
ProCarManuals.com

8-25
E
HULL
HOOD
REMOTE CONTROL CABLES AND
SPEED SENSOR LEAD
EXPLODED DIAGRAM
Step Procedure/Part name Q’ty Service points
14 Shift cable end 1 Deluxe model only
15 Grommet 1 Deluxe model only
16 Nut 1 Deluxe model only
17 Shift cable 1 Deluxe model only
18 Seal 1 Deluxe model only
Reverse the removal steps for installation.
ProCarManuals.com

8-26
E
HULL
HOOD
REMOTE CONTROL CABLES AND
SPEED SENSOR LEAD
SERVICE POINTS
WARNING
When routing the cables, do not grasp the
cable by the outer crimped sheath or steel
end. This could deform or loosen the cable
end due to extreme angles and or pressure.
Always hold the cables by the outer cover
below the crimp.
If a cable becomes damaged replace it.
Never attempt to repair a damaged cable.
Remote control cables inspection
1. Inspect:
Steering cable
Shift cable (Deluxe model only)
Frays/kinks/rough movement →

Replace.
Steering cable (jet pump end) installation
1. Install:
Steering cable
WARNING
The steering cable must be screwed in at
least 8 mm (0.31 in).
Steering cable set length
a
(jet pump end):
14.5 mm (0.57 in)
Steering cable stopper installation
1. Install:
Steering cable stopper
WARNING
Be sure to the steering cable stopper into
the groove in the outer cable as shown in
the illustration.
ProCarManuals.com