brake YAMAHA WARRIOR 350 2001 User Guide

5-5
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-5.frame
EL
EBU00481
Front and rear brakes
1. Brake lever and brake pedal
Check for correct free play in the front
brake lever. If the free play is incorrect, ad-
just it. Check for correct rear brake pedal
height. If the pedal height is incorrect,
have a Yamaha dealer adjust it. (See
pages 8-47 ~ 8-49.)
Check the operation of the lever and ped-
al. They should move smoothly and there
should be a firm feeling when the brakes
are applied. If not, have the machine in-
spected by a Yamaha dealer.
2. Brake fluid level
Check the brake fluid level.
Add fluid if necessary. (See pages 8-41 ~
8-45.)
NOTE:

If DOT 4 is not available, DOT 3 can be used.Recommended brake fluid: DOT 4

5-7
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-5.frame
EL
3. Brake fluid leakage
Check to see if any brake fluid is leaking
out of the pipe joints or master cylinders.
Apply the brakes firmly for one minute. If
there is any leaking, have the machine in-
spected by a Yamaha dealer.
4. Brake operation
Test the brakes at slow speed after start-
ing out to make sure they are working
properly. If the brakes do not provide
proper braking performance, inspect the
brake pads for wear. (See page 8-39.)
WARNING

Always check the brakes at the start of every
ride. Do not ride the ATV if you find any prob-
lem with the brakes or you could lose braking
ability, which could lead to an accident. If a
problem cannot be corrected by the adjust-
ment procedures provided in this manual,
have the ATV inspected by a Yamaha dealer.

6-3
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-6.frame
EL
EBU00514
Starting a cold engine
WARNING

Always make sure all control cables work
smoothly before you begin riding in cold
weather. If the control cables are frozen or do
not work smoothly, you could be unable to
control the ATV, which could lead to an acci-
dent or collision.
1. Set the parking brake.
2. Turn the fuel cock to “ON”.
3. Turn the main switch to “ON” and the en-
gine stop switch to “RUN”.
4. Shift the transmission into neutral.

6-9
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-6.frame
EL
EBU00180
Starting a warm engine
To start a warm engine, refer to the “Starting a
cold engine” section. The starter (choke)
should not be used. The throttle should be
opened slightly.
EBU00538
Warming up
To get maximum engine life, always warm up
the engine before starting off. Never accelerate
hard with a cold engine! To see whether or not
the engine is warm, check if it responds to the
throttle normally with the starter (choke)
turned off.NOTE:

When the parking brake is used, engine speed
is limited to 2,300 r/min. Be sure the parking
brake is released before moving the throttle le-
ver. Otherwise, the engine will misfire, pre-
venting normal operation.

6-11
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-6.frame
EL
EBU00188
Drive select lever operation and reverse driv-
ing
CAUTION:

Before shifting, stop the machine and return
the throttle lever to its closed position. Other-
wise the transmission may be damaged.
NOTE:

When shifting into reverse, the clutch must be
disengaged.
1. Bring the machine to a complete stop and
return the throttle lever to the closed posi-
tion.
2. Pull in the clutch lever to disengage the
clutch.
3. Apply the rear brake pedal.
4. While pulling the knob, move the drive se-
lect lever toward the rear until it complete-
ly stops.
NOTE:

When in reverse, the reverse indicator light
should be on. If the light does not come on, ask
a Yamaha dealer to inspect the machine.
1. Drive select lever
2. Knob
3. For forward drive
4. For reverse drive
1. Levier de présélection
2. Bouton
3. Conduite en marche avant
4. Conduite en marche arrière
1. Palanca de selección de gama
2. Botón
3. Para marcha adelante
4. Para marcha atrás

6-13
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-6.frame
EL
5. Check behind you for people or obstacles,
then release the rear brake pedal.
6. Open the throttle lever gradually and re-
lease the clutch lever slowly. Continue to
watch to the rear while backing.
WARNING

Improper operation in reverse could make you
hit an obstacle or person behind you, resulting
in serious injury. When you shift into reverse,
make sure there are no obstacles or people be-
hind you. When it is safe to proceed, go slowly.

6-21
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-6.frame
EL
EBU00208
To decelerate:
When slowing down or stopping, release the
throttle and apply the brakes smoothly and
evenly. As you slow down, shift to a lower
gear. Be sure that the engine has sufficiently
slowed before engaging a lower gear. Improp-
er use of the brakes or shifting can cause the
tires to lose traction, reducing control and in-
creasing the possibility of an accident.
WARNING
Make sure the engine has sufficiently slowed
before shifting to a lower gear. Engaging a
lower gear when the engine speed is too high
could make the wheels stop rotating. This
could cause loss of control, an accident and in-
jury. It could also cause engine or drive traindamage.

6-27
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-6.frame
EL
EBU00211
Parking
When parking, stop the engine and shift into
neutral. Turn the fuel cock to “OFF” and apply
the parking brake.
1. Button 2. Lock plate
1. Bouton 2. Verrou
1. Botón 2. Placa de bloqueo1. Lock position
1. Position de verrouillage
1. Posición de bloqueo

6-29
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-6.frame
EL
EBU00214
Parking on a slope
WARNING
Avoid parking on hills or other inclines. Park-
ing on a hill or other incline could cause the
ATV to roll out of control, increasing the
chance of an accident. If you must park on an
incline, put the machine in low gear, apply the
parking brake, and block the front and rear
wheels with rocks or other objects.
Do not park the ATV at all on hills that are sosteep you could not walk up them easily.
1. Bring the machine to a stop by applying
the brakes in low gear.
2. Stop the engine and release the clutch le-
ver.
3. With the front and rear brakes applied, ap-
ply the parking brake and slowly release
the rear brake pedal.

7-33
Yuki_Data:Yuki_data:Yuki:Yuki_1:ATV:HM00B067_YFM350X-60:YFM350-7.frame
EL
Select a large, flat area off-road to become fa-
miliar with your ATV. Make sure that this area
is free of obstacles and other riders. You
should practice control of the throttle, brakes,
shifting procedures, and turning techniques in
this area before trying more difficult terrain. Al-
ways avoid riding on paved surfaces: the ATV
is designed for off-road use only, and handling
maneuvers are more difficult to perform on
pavement.
Set the parking brake and follow the instruc-
tion on page 6-3 to start the engine. Once it has
warmed up you are ready to begin riding your
ATV. As you get on the ATV, be sure not to ac-
cidentally move the shift pedal. Remember
that the engine and exhaust pipe will be hot
when riding and afterwards; do not allow skin
or clothing to come in contact with these com-
ponents.