oil YAMAHA WHY 50 2003 Owner's Manual

SCOOTER CARE AND STORAGE
7
EWA00002
•Make sure that there is no oil
or wax on the brakes or tires. If
necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or
acetone, and wash the tires with
warm water and a mild
detergent.
•Before operating the scooter
test its braking performance
and cornering behavior.
ECA00013
•Apply spray oil and wax
sparingly and make sure to
wipe off any excess.
•Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.
•Avoid using abrasive polishing
compounds as they will wear
away the paint.
NOTE :
Consult a Yamaha dealer for advice on
what products to use.
Storage
Short-term
Always store your scooter in a cool, dry
place and, if necessary, protect it
against dust with a porous cover.
ECA00015
•Storing the scooter in a poorly
ventilated room or covering it
with a tarp, while it is still wet,
will allow water and humidity to
seep in and cause rust.
•To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong
chemicals are stored.Long-term
Before storing your scooter for several
months:
1. Follow all the instructions in the
"Care" section of this chapter.
2. Drain the carburetor float chamber
by loosening the drain bolt; this will
prevent fuel deposits from building
up. Pour the drained fuel into the
fuel tank.
3. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
4. Perform the following steps to
protect the cylinder, piston rings,
etc. from corrosion.
7-3

SCOOTER CARE AND STORAGE
7 a. Remove the spark plug cap
and spark plug.
b. Pour a teaspoonful of engine
oil into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit
sparking during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap
from the spark plug, and then
install the spark plug and the
spark plug cap.
EWA00003
To prevent damage or injury from
sparking, make sure to ground the
spark plug electrodes while turning
the engine over.
5. Lubricate all control cables and
the pivoting points of all levers and
pedals as well as of the sidestand/
centerstand.
6. Check and, if necessary, correct
the tire air pressure, and then lift
the scooter so that both of its
wheels are off the ground.
Alternatively, turn the wheels a
little every month in order to
prevent the tires from becoming
degraded in one spot.
7. Cover the muffler outlet with a
plastic bag to prevent moisture
from entering it.
8. Remove the battery and fully
charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an
excessively cold or warm place
(less than 0 °C or more than 30
°C). For more information on
storing the battery, see page 6-
18.
NOTE :
Make any necessary repairs before
storing the scooter.
7-4

SPECIFICATIONS
8
Model YH50
Dimensions:
Overall length 1.940 mm
Overall width 685 mm
Overall height 1.105 mm
Seat height 765 mm
Wheelbase 1.294 mm
Minimum ground clearance 125 mm
Minimum turning radius 1.800 mm
Weight:
Wet (with oil and a full fuel tank) 78 kg
Engine:
Engine type Air cooled, 2 strokes
Cylinder arrangement Single cylinder, horizontal
Displacement 49.2 cm3
Bore x stroke 40.0 x 39.2
Compression ratio 7.25:1
Starting system type Electric and kick starter
Lubrication system Separate lubrication
(Autolube)
Engine oil:
Type Yamalube 2
or 2 strokes engine oil
Classification Jaso FC ou ISO EG-C, EG-D
Capacity 1.3 LTransmission oil:
Type SAE 10W30 type SE
Capacity
Périodic oil change 0.11L
Total amount 0.13L
Air filter type:Wet type element
Fuel:
Recommended fuel Regular unleaded gasoline
(RON 91 mini)
Fuel tank capacity 7L
Carburetor:
Type / quantity PY-12
Manufacturer GURTNER
Spark plug:
Type / Manufacturer BR8HS / NGK
Spark plug gap 0.6—0.7 mm
Clutch type:Dry, centrifugal automatic
Transmission:
Primary reduction system Helical gear
Primary reduction ratio 52/13 (4.000)
Secondary reduction system Spur gear
Secondary reduction ratio 45/12 (3.750)
Transmission type V-belt automatic
Operation Centrifugal automatic type
8-1
Specifications

SPECIFICATIONS
8
Chassis:
Frame type Steel tube underbone
Caster angle ((degree)) 25°
Trail 101.3 mm
Tires:
Front:
Type Tubeless
Size 2 1/2-16 42M
Manufacturer / Model MICHELIN / M29S TT
Rear:
Type Tubeless
Size 2 3/4-16 46M
Manufacturer / Model MICHELIN / M29S TT
Maximum load * 182 Kg
Air pressure (cold tire):
Up to 90 Kg load*
Front180 kpa
Rear 190 kpa
90 kg load — maximum
load *
Front180 kpa
Rear 210 kpa
* Total weight of rider, passenger, cargo and accessories.Wheels:
Front
Type Cast wheel
Size 16 X MT 1.60
Rear
Type Cast wheel
Size 16 X MT 1.85
Brakes:
Front
Type Single disc brake
Operation Right hand operation
Type brake fluid DOT 4
Rear
Type Single drum brake
Operation Left hand operation
Suspension:
Front suspension Telescopic fork
Rear suspension Unit swing
Shock absorber:
Front fork type Coil spring/oil damper
Rear shock absorber Coil spring/oil damper
assembly type
Wheel travel:
Front wheel travel 80 mm
Rear wheel travel 70 mm
8-2

SPECIFICATIONS
8
Electrical:
Ignition system typeC.D.I
Charging system Flywheel magneto
Battery
Model GM4-3B, YB4L-B, FB4L-B
Voltage/capacity 12 V / 4 Ah
Headlight type:Bulb
Bulbs (voltage/wattage x quantity):
Headlight 12V, 35W/35Wx1
Brake/brake light 12V, 5W/21Wx1
Turn signal light
Front 12V, 10Wx2
Rear 12V, 10Wx2
Meter lights 12V, 1.2Wx2
High beam indicator light 12V, 1.2Wx1
Turn signal indicator light 12V, 1.2Wx1
Oil warning light 12V, 2Wx1
Fuses:
Main fuse 7.5 A
8-3