engine oil YAMAHA XENTER 150 2016 User Guide

[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2016, Model line: XENTER 150, Model: YAMAHA XENTER 150 2016
Pages: 84, PDF Size: 1.88 MB

Load previous 10 pages

Page 48 of 84

YAMAHA XENTER 150 2016 User Guide Periodic maintenance and adjustment
6-13
1
2
3
4
56
7
8
9
10
11
12 spring, O-ring and engine oil drain
bolt B.
TIPMake sure that the O-ring is properlyseated.
7. Install engine oil drain bolt A, and t

Periodic maintenance and adjustment
6-13
1
2
3
4
56
7
8
9
10
11
12 spring, O-ring and engine oil drain
bolt B.
TIPMake sure that the O-ring is properlyseated.
7. Install engine oil drain bolt A, and then tighten both drain bolts to
their specified torques.
8. Refill with the specified amount of the recommended engine oil, and
then install and tighten the oil filler
cap.NOTICE
ECA11671

Do not use oils with a diesel
specification of “CD” or oils of a
higher quality than specified. In addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.

Be sure no foreign material en-ters the crankcase.
9. Start the engine, and then let it idle for several minutes while checking
it for oil leakage. If oil is leaking, im-
mediately turn the engine off and
check for the cause.
10. Turn the engine off, and then check the oil level and correct it if
necessary.
To reset the oil change indicator
and oil change tripmeter
TIPThe oil change indicator and oil change
tripmeter can be reset when "OIL
CHANGE" and "OIL TRIP" appear in
the multi-function display. (Seepage 3-3.)
EAU20067
Final transmission oilThe final transmission case must be
checked for oil leakage before each
ride. If any leakage is found, have a
Yamaha dealer check and repair the
scooter. In addition, the final transmis-
sion oil must be changed as follows at
the intervals specified in the periodic
maintenance and lubrication chart. 1. Start the engine, warm up the final transmission oil by riding the
scooter for several minutes, and
then stop the engine.
2. Place the scooter on the center- stand.
3. Place an oil pan under the final transmission case to collect the
used oil.
4. Remove the final transmission oil filler cap and its O-ring from the fi-
nal transmission case.
Tightening torque:Engine oil drain bolt A: 20 Nm (2.0 m·kgf, 14.5 ft·lbf)
Engine oil drain bolt B:
32 Nm (3.2 m·kgf, 23.1 ft·lbf)
Recommended engine oil: See page 8-1.
Oil change quantity:
1.10 L (1.16 US qt, 0.97 Imp.qt)
U52SE1E0 13 ページ２０１５年９月１６日　水曜日　午後５時２７分

Page 49 of 84

YAMAHA XENTER 150 2016 User Guide Periodic maintenance and adjustment6-14
1
2
3
4
567
8
9
10
11
12
5. Remove the final transmission oil
drain bolt and its gasket to drain
the oil from the final transmission
case.
6. Install the final

Page 70 of 84

YAMAHA XENTER 150 2016 User Guide 7-1
1
2
3
4
5
67
8
9
10
11
12
Scooter care and storage
EAU37834
Matte color cautionNOTICE
ECA15193
Some models are equipped with
matte colored finished parts. Be
sure to consult a Yamaha dealer for
ad

7-1
1
2
3
4
5
67
8
9
10
11
12
Scooter care and storage
EAU37834
Matte color cautionNOTICE
ECA15193
Some models are equipped with
matte colored finished parts. Be
sure to consult a Yamaha dealer for
advice on what products to use be-
fore cleaning the vehicle. Using a
brush, harsh chemical products or
cleaning compounds when cleaning
these parts will scratch or damage
their surface. Wax also should not
be applied to any matte colored fin-ished parts.
EAU26096
CareWhile the open design of a scooter re-
veals the attractiveness of the technol-
ogy, it also makes it more vulnerable.
Rust and corrosion can develop even if
high-quality components are used. A
rusty exhaust pipe may go unnoticed
on a car, however, it detracts from the
overall appearance of a scooter. Fre-
quent and proper care does not only
comply with the terms of the warranty,
but it will also keep your scooter looking
good, extend its life and optimize its
performance.
Before cleaning 1. Cover the muffler outlet with a plastic bag after the engine has
cooled down.
2. Make sure that all caps and covers as well as all electrical couplers
and connectors, including the
spark plug cap, are tightly in-
stalled.
3. Remove extremely stubborn dirt, like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such prod- ucts onto seals, gaskets and wheel
axles. Always rinse the dirt and de-
greaser off with water.
Cleaning
NOTICE
ECA10784

Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the af-
fected area any longer than in-
structed. Also, thoroughly rinse
the area off with water, immedi-
ately dry it, and then apply a cor-
rosion protection spray.

Improper cleaning can damage
plastic parts (such as cowlings,
panels, windshields, headlight
lenses, meter lenses, etc.) and
the mufflers. Use only a soft,
clean cloth or sponge with wa-
ter to clean plastic. However, if
the plastic parts cannot be thor-
oughly cleaned with water, di-
luted mild detergent with water
may be used. Be sure to rinse
off any detergent residue using
U52SE1E0 1 ページ２０１５年９月１６日　水曜日　午後５時２７分

Page 73 of 84

YAMAHA XENTER 150 2016 User Guide Scooter care and storage
7-4
1
2
3
4
5
678
9
10
11
12
EAU36564
StorageShort-term
Always store your scooter in a cool, dry
place and, if necessary, protect it
against dust with a porous cover. Be
sure

Scooter care and storage
7-4
1
2
3
4
5
678
9
10
11
12
EAU36564
StorageShort-term
Always store your scooter in a cool, dry
place and, if necessary, protect it
against dust with a porous cover. Be
sure the engine and the exhaust sys-
tem are cool before covering the scoot-
er.NOTICE
ECA10821

Storing the scooter in a poorly
ventilated room or covering it
with a tarp, while it is still wet,
will allow water and humidity to
seep in and cause rust.

To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-cals are stored.
Long-term
Before storing your scooter for several
months: 1. Follow all the instructions in the “Care” section of this chapter. 2. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
3. Perform the following steps to pro- tect the cylinder, piston rings, etc.
from corrosion.
a. Remove the spark plug cap and spark plug.
b. Pour a teaspoonful of engine oil into the spark plug bore.
c. Install the spark plug cap onto the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap from the spark plug, and then
install the spark plug and the
spark plug cap. WARNING! To
prevent damage or injury
from sparking, make sure to
ground the spark plug elec-
trodes while turning the en-
gine over.
[EWA10952]
4. Lubricate all control cables and the pivoting points of all levers and
pedals as well as of the sidestand/
centerstand.
5. Check and, if necessary, correct the tire air pressure, and then lift
the scooter so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
6. Cover the muffler outlet with a plastic bag to prevent moisture
from entering it.
7. Remove the battery and fully charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an ex-
cessively cold or warm place [less
than 0  C (30 F) or more than 30
 C (90 F)]. For more information
on storing the battery, see page
6-26.TIPMake any necessary repairs beforestoring the scooter.
U52SE1E0 4 ページ２０１５年９月１６日　水曜日　午後５時２７分

Page 74 of 84

YAMAHA XENTER 150 2016 User Guide 8-1
1
2
3
4
5
6
78
9
10
11
12
Specifications
EAU72940
Dimensions:Overall length: 1990 mm (78.3 in)
Overall width: 690 mm (27.2 in)
Overall height: 1135 mm (44.7 in)
Seat height:
785 mm (30.9 in)
Wheel

Page 79 of 84

YAMAHA XENTER 150 2016 User Guide Index
AAcceleration and deceleration ................... 5-2
Air filter and V-belt case air filter
elements ................................................ 6-16
Auxiliary light bulb, replacing .....

Index
AAcceleration and deceleration ................... 5-2
Air filter and V-belt case air filter
elements ................................................ 6-16
Auxiliary light bulb, replacing ................... 6-29BBattery ..................................................... 6-26
Brake fluid, changing ............................... 6-23
Brake fluid level, checking ....................... 6-22
Brake lever, front ....................................... 3-7
Brake lever, rear ........................................ 3-8
Brake levers, lubricating .......................... 6-24
Brake pads and shoes, checking............. 6-21
Braking ...................................................... 5-3CCables, checking and lubricating ............. 6-23
Care ........................................................... 7-1
Carrier...................................................... 3-14
Catalytic converter ................................... 3-10
Centerstand, checking and lubricating .... 6-24
Coolant .................................................... 6-14
Coolant temperature warning light............. 3-2
Cowling and panels, removing and installing .................................................. 6-8DDimmer switch ........................................... 3-7EEngine break-in ......................................... 5-3
Engine idling speed, checking ................. 6-17
Engine oil ................................................. 6-11
Engine serial number................................. 9-1
Engine trouble warning light ...................... 3-3FFinal transmission oil ............................... 6-13 Front brake lever free play, checking ...... 6-20
Front fork, checking................................. 6-25
Fuel ........................................................... 3-9
Fuel consumption, tips for reducing .......... 5-3
Fuel tank cap............................................. 3-8
Fuses, replacing ...................................... 6-28
HHandlebar switches ................................... 3-7
Headlight bulb, replacing......................... 6-28
High beam indicator light........................... 3-2
Horn switch ............................................... 3-7IIdentification numbers ............................... 9-1
Indicator lights and warning lights ............. 3-2LLicense plate light ................................... 6-32
Luggage holder ....................................... 3-14MMain switch/steering lock .......................... 3-1
Maintenance and lubricatio
n, periodic....... 6-5
Maintenance, emission control system ..... 6-4
Matte color, caution ................................... 7-1
Model label ................................................ 9-2
Multi-function display................................. 3-3PParking ...................................................... 5-4
Part locations ............................................ 2-1
Passenger footrest .................................. 3-11RRear brake lever free play, adjusting ...... 6-20SSafe-riding points ...................................... 1-5
Safety information ..................................... 1-1
Seat ......................................................... 3-11 Shock absorber assembly .......................3-13
Spark plug, checking ...............................6-10
Specifications.............................................8-1
Starting off .................................................5-2
Starting the engine.....................................5-1
Start switch ................................................3-7
Steering, checking ...................................6-26
Storage ......................................................7-4
Storage compartments ............................3-12
TTail/brake light ......................................... 6-30
Throttle grip and cable, checking and
lubricating ..............................................6-24
Throttle grip free play, checking...............6-17
Tires .........................................................6-18
Tool kit .......................................................6-2
Troubleshooting .......................................6-32
Troubleshooting charts ............................6-33
Turn signal indicator lights .........................3-2
Turn signal light bulb (front), replacing ....6-30
Turn signal light bulb (r ear), replacing .....6-31
Turn signal switch ......................................3-7VValve clearance .......................................6-18
Vehicle identificat ion number .....................9-1WWheel bearings, checking........................6-26
Wheels .....................................................6-20
U52SE1E0 1 ページ２０１５年９月１６日　水曜日　午後５時２７分

Page: < prev 1-10 11-20