engine YAMAHA XT500E 2002 Owner's Guide

6-27
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU02962
Checking and lubricating the
cablesCables, checking and lubricatingThe operation of all control cables
and the condition of the cables
should be checked before each ride,
and the cables and cable ends
should be lubricated if necessary. If a
cable is damaged or does not move
smoothly, have a Yamaha dealer
check or replace it.
EAU04034
Checking and lubricating the
throttle grip and cableThrottle grip and cable, checking and lubricatingThe operation of the throttle grip
should be checked before each ride.
In addition, the cable should be lubri-
cated or replaced at the intervals
specified in the periodic maintenance
chart.
EW000112
wDamage to the outer sheath may
interfere with proper cable opera-
tion and will cause the inner cable
to rust. Replace a damaged cable
as soon as possible to prevent
unsafe conditions.
Recommended lubricant:
Engine oil
4PT-E7 (English) 6/29/01 9:13 AM Page 64

6-30
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU00794
Checking the steeringSteering, checkingWorn or loose steering bearings may
cause danger. Therefore, the opera-
tion of the steering must be checked
as follows at the intervals specified in
the periodic maintenance and lubrica-
tion chart.
1. Place a stand under the engine
to raise the front wheel off the
ground.
EW000115
wSecurely support the motorcycle
so that there is no danger of it
falling over.
EAU01144
Checking the wheel bearingsWheel bearings, checkingThe front and rear wheel bearings
must be checked at the intervals
specified in the periodic maintenance
and lubrication chart. If there is play
in the wheel hub or if the wheel does
not turn smoothly, have a Yamaha
dealer check the wheel bearings.
2. Hold the lower ends of the front
fork legs and try to move them
forward and backward. If any
free play can be felt, have a
Yamaha dealer check or repair
the steering.
4PT-E7 (English) 6/29/01 9:13 AM Page 67

6-36
PERIODIC MAINTENANCE AND MINOR REPAIR
6 2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.
EC000108
cCDo not overtighten the screws,
otherwise the lens may break.
1
1. Bulb
To service the rear wheel
Raise the rear wheel off the ground
by using a motorcycle stand or, if a
motorcycle stand is not available, by
placing a jack either under each side
of the frame in front of the rear wheel
or under each side of the swingarm.
EAU01579
Supporting the motorcycleSupporting the motorcycleSince this model is not equipped with
a centerstand, follow these precau-
tions when removing the front and
rear wheel or performing other main-
tenance requiring the motorcycle to
stand upright. Check that the motor-
cycle is in a stable and level position
before starting any maintenance. A
strong wooden box can be placed
under the engine for added stability.
To service the front wheel
1. Stabilize the rear of the motorcy-
cle by using a motorcycle stand
or, if an additional motorcycle
stand is not available, by placing
a jack under the frame in front of
the rear wheel.
2. Raise the front wheel off the
ground by using a motorcycle
stand.
4PT-E7 (English) 6/29/01 9:13 AM Page 73

6-42
PERIODIC MAINTENANCE AND MINOR REPAIR
6
1. Fuel
2. Compression
3. Ignition
4. Battery
Use electric starter.
There is compression.
Go to ignition check.
No compression.
Ask a Yamaha dealer to inspect.Wet.
Dry.Wipe clean with dry cloth and
Ask a Yamaha dealer to inspect.
Check if there is fuel
Enough fuel
No fuel
Go to compression check.Supply fuel.
in the fuel tank.
Remove sparkelectrodes. plug and checkOpen throttle half-way and start the
Engine doesn’t start, go to batterycheck.engine. correct spark gap or replace spark plug.
Engine turns over
Engine turns overBattery good.
Check connections
quickly.
slowly. or recharge.Engine doesn’t start, ask a Yamaha
dealer to inspect.
Engine doesn’t start, go to compression check.
Use the electric
starter.
EAU01397
Troubleshooting chartTroubleshooting chart
EW000125
wKeep away open flames and do not smoke while checking or working on the fuel system.
4PT-E7 (English) 6/29/01 9:13 AM Page 79

7-1
EAU03521
MOTORCYCLE CARE AND STORAGE
7
CareCareWhile the open design of a motorcy-
cle reveals the attractiveness of the
technology, it also makes it more vul-
nerable. Rust and corrosion can
develop even if high-quality compo-
nents are used. A rusty exhaust pipe
may go unnoticed on a car, however,
it detracts from the overall appear-
ance of a motorcycle. Frequent and
proper care does not only comply
with the terms of the warranty, but it
will also keep your motorcycle looking
good, extend its life and optimize its
performance.Before cleaning
1. Cover the muffler outlet with a
plastic bag after the engine has
cooled down.
2. Make sure that all caps and cov-
ers as well as all electrical cou-
plers and connectors, including
the spark plug cap, are tightly
installed.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such
products onto seals, gaskets,
sprockets, the drive chain and
wheel axles. Always rinse the dirt
and degreaser off with water.Cleaning
ECA00010
cC8
8
Avoid using strong acidic
wheel cleaners, especially on
spoked wheels. If such prod-
ucts are used on hard-to-
remove dirt, do not leave the
cleaner on the affected area
any longer than instructed.
Also, thoroughly rinse the area
off with water, immediately dry
it, and then apply a corrosion
protection spray.
8 8
Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or
sponge with mild detergent
and water to clean plastic.
4PT-E7 (English) 6/29/01 9:13 AM Page 82

7-2
MOTORCYCLE CARE AND STORAGE
7 8 8
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abra-
sive cleaning products, sol-
vent or thinner, fuel (gasoline),
rust removers or inhibitors,
brake fluid, antifreeze or elec-
trolyte.
8 8
Do not use high-pressure
washers or steam-jet cleaners
since they cause water seep-
age and deterioration in the
following areas: seals (of
wheel and swingarm bearings,
fork and brakes), electric com-
ponents (couplers, connec-
tors, instruments, switches
and lights), breather hoses
and vents.8 8
For motorcycles equipped
with a windshield: Do not use
strong cleaners or hard
sponges as they will cause
dulling or scratching. Some
cleaning compounds for plas-
tic may leave scratches on the
windshield. Test the product
on a small hidden part of the
windshield to make sure that it
does not leave any marks. If
the windshield is scratched,
use a quality plastic polishing
compound after washing.
After normal useRemove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottle-
brush for hard-to-reach areas.
Stubborn dirt and insects will come
off more easily if the area is covered
with a wet cloth for a few minutes
before cleaning.After riding in the rain, near the sea
or on salt-sprayed roadsSince sea salt or salt sprayed on
roads during winter are extremely
corrosive in combination with water,
carry out the following steps after
each ride in the rain, near the sea or
on salt-sprayed roads.NOTE:
Salt sprayed on roads in the winter
may remain well into spring.1. Clean the motorcycle with cold
water and a mild detergent, after
the engine has cooled down.
ECA00012
cCDo not use warm water since it
increases the corrosive action of
the salt.2. Apply a corrosion protection
spray on all metal, including
chrome- and nickel-plated, sur-
faces to prevent corrosion.
4PT-E7 (English) 6/29/01 9:13 AM Page 83

7-4
MOTORCYCLE CARE AND STORAGE
7
StorageStorageShort-term
Always store your motorcycle in a
cool, dry place and, if necessary, pro-
tect it against dust with a porous
cover.
ECA00014
cC8Storing the motorcycle in a
poorly ventilated room or cov-
ering it with a tarp, while it is
still wet, will allow water and
humidity to seep in and cause
rust.
8To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-
cals are stored.
Long-term
Before storing your motorcycle for
several months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. For motorcycles equipped with a
fuel cock that has an “OFF” posi-
tion: Turn the fuel cock lever to
“OFF”.
3. Drain the carburetor float cham-
ber by loosening the drain bolt;
this will prevent fuel deposits
from building up. Pour the
drained fuel into the fuel tank.
4. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
5. Perform the following steps to
protect the cylinder, piston rings,
etc. from corrosion.
a. Remove the spark plug cap
and spark plug.
b. Pour a teaspoonful of engine
oil into the spark plug bore.c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes
are grounded. (This will limit
sparking during the next step.)
d. Turn the engine over several
times with the starter. (This
will coat the cylinder wall with
oil.)
e. Remove the spark plug cap
from the spark plug, and then
install the spark plug and the
spark plug cap.
EWA00003
wTo prevent damage or injury from
sparking, make sure to ground the
spark plug electrodes while turn-
ing the engine over.
4PT-E7 (English) 6/29/01 9:13 AM Page 85

8-1
EAU01038
SPECIFICATIONS
8
SpecificationsSpecifications
Model XT500E/XT600E
Dimensions
Overall length 2,220 mm
2.295 mm (N, S, CH only)
Overall width 865 mm
825 mm (CH only)
Overall height 1,205 mm
Seat height 855 mm
Wheel base 1,440 mm
Ground clearance 230 mm
Minimum turning radius 2,300 mm
Basic weight (with oil and full
fuel tank)176 kg
172 kg (CH only)
Engine
Engine type Air-cooled 4-stroke, SOHC,
gasoline
Cylinder arrangement Forward inclined single
cylinder
Displacement 499 cm
3
595 cm
3
Bore ×Stroke 87.0 ×84.0 mm (XT500E)
95.0 ×84.0 mm (XT600E)
Compression ratio 8.5:1
Starting system Electric starter
Lubrication system Dry sump
Engine oil
Type
Recommended engine oil
classification API Service SE, SF, SG type
or highercCBe sure to use motor oils that do not contain anti-friction
modifiers. Passenger car motor oils (often labeled
“ENERGY CONSERVING II”) contain anti-friction additives
which will cause clutch and/or starter clutch slippage, result-
ing in reduced component life and poor engine performance.
Capacity
Without oil filter element
replacement 2.7 L
With oil filter element
replaced 2.8 L
Total amount (dry engine) 3.3 L
–10° 0° 10° 20° 30°
40°
SAE 10W/30
SAE 10W/40
SAE 20W/40
SAE 20W/50
–20°
SAE 15W/40 50°C
4PT-E7 (English) 6/29/01 9:13 AM Page 88

INDEX
E
Engine break-in ..................................... 5-4
Engine idling speed ............................. 6-15
Engine oil and oil filter element ........... 6-10
Engine, starting a warm ......................... 5-2
F
Front and rear brake pads, checking ... 6-22
Front fork, checking ............................. 6-29
Front wheel........................................... 6-37
Installing ............................................ 6-37
Removing .......................................... 6-37
Fuel ....................................................... 3-6
Fuel cock ............................................... 3-8
Fuel consumption, tips for reducing ...... 5-4
Fuel tank cap ......................................... 3-6
Fuse, replacing .................................... 6-32
H
Handlebar switches ............................... 3-3
Light switch ......................................... 3-3
Pass switch ......................................... 3-3
Dimmer switch .................................... 3-3
Turn signal switch ............................... 3-3
Horn switch ......................................... 3-3
Engine stop switch .............................. 3-4
Start switch ......................................... 3-4
Headlight bulb, replacing ..................... 6-33
Helmet holder ...................................... 3-10
I
Identification numbers ........................... 9-1
Ignition circuit cut-off system ............... 3-12
Indicator lights ....................................... 3-2
High beam indicator light .................... 3-2
Neutral indicator light .......................... 3-2
Turn signal indicator light .................... 3-2
K
Key identification number ...................... 9-1
M
Main switch/steering lock ...................... 3-1
Model label ............................................ 9-2
P
Parking .................................................. 5-5
Part locations ......................................... 2-1
Periodic maintenance and lubrication
chart .................................................... 6-3
Pre-operation check list ......................... 4-1
R
Rear brake light switch, adjusting ........ 6-22
Rear suspension, lubricating ............... 6-29
Rear wheel ........................................... 6-39
Removing .......................................... 6-39
Install ................................................ 6-40
S
Seat ....................................................... 3-9
Shift pedal ............................................. 3-5
Shift points (for Switzerland only) .......... 5-3
Shifting .................................................. 5-3
Shock absorber assembly, adjusting ... 3-10
Sidestand ............................................ 3-11
A
Air filter element, cleaning ................... 6-13
B
Battery ................................................. 6-31
Brake and clutch levers, checking and
lubricating ......................................... 6-28
Brake and shift pedals, checking and
lubricating ......................................... 6-28
Brake fluid level, checking ................... 6-23
Brake fluid, changing ........................... 6-24
Brake lever ............................................ 3-5
Brake lever free play, adjusting ........... 6-21
Brake pedal ........................................... 3-5
Brake pedal position, adjusting ........... 6-21
C
Cables, checking and lubricating ......... 6-27
Carburetor, adjusting ........................... 6-14
Care ....................................................... 7-1
Clutch lever ........................................... 3-4
Clutch lever free play, adjusting .......... 6-20
Conversion table ................................... 8-5
Cowling and panels, removing and
installing .............................................. 6-6
D
Drive chain slack ................................. 6-25
Checking ........................................... 6-25
Adjusting ........................................... 6-25
Drive chain, lubricating ........................ 6-26
4PT-E7 (English) 6/29/01 9:13 AM Page 96

Sidestand, checking and lubricating .... 6-28
Spark plug, checking ............................. 6-8
Specifications ........................................ 8-1
Speedometer unit .................................. 3-2
Starter (choke) knob .............................. 3-9
Starting the engine ................................ 5-1
Steering, checking ............................... 6-30
Storage .................................................. 7-4
Supporting the motorcycle ................... 6-36
T
Tachometer ........................................... 3-3
Tail/brake light bulb, replacing ............. 6-35
Throttle cable free play, adjusting ....... 6-16
Throttle grip and cable, checking and
lubricating ......................................... 6-27
Tires .................................................... 6-16
Tool kit ................................................... 6-1
Troubleshooting ................................... 6-41
Troubleshooting chart .......................... 6-42
Turn signal light bulb, replacing ........... 6-35
V
Valve clearance, adjusting .................. 6-16
Vehicle identification number ................ 9-1
W
Wheel bearings, checking ................... 6-30
Wheels ................................................ 6-19
INDEX
4PT-E7 (English) 6/29/01 9:13 AM Page 97