ignition YAMAHA XT500E 2002 Owners Manual

INSTRUMENT AND CONTROL FUNCTIONSMain switch/steering lock .................................................................. 3-1
Indicator lights .................................................................................. 3-2
Speedometer unit ............................................................................ 3-2
Tachometer ...................................................................................... 3-3
Handlebar switches .......................................................................... 3-3
Clutch lever ....................................................................................... 3-4
Shift pedal ......................................................................................... 3-5
Brake lever ....................................................................................... 3-5
Brake pedal ...................................................................................... 3-5
Fuel tank cap .................................................................................... 3-6
Fuel ................................................................................................... 3-6
Fuel cock .......................................................................................... 3-8
Starter (choke) knob ......................................................................... 3-9
Seat .................................................................................................. 3-9
Helmet holder ................................................................................. 3-10
Adjusting the shock absorber assembly ......................................... 3-10
Sidestand ........................................................................................ 3-11
Ignition circuit cut-off system .......................................................... 3-12
3
4PT-E7 (English) 6/29/01 9:13 AM Page 13

3-1
EAU00029
Main switch/steering lockMain switch/steering lockThe main switch/steering lock con-
trols the ignition and lighting systems,
and is used to lock the steering. The
various positions are described
below.
EAU00036
ON
All electrical systems are supplied
with power, and the engine can be
started. The key cannot be removed.
EAU00038
OFF
All electrical systems are off. The key
can be removed.
EW000016
wNever turn the key to “OFF” or
“LOCK” while the motorcycle is
moving, otherwise the electrical
systems will be switched off,
which may result in loss of control
or an accident. Make sure that the
motorcycle is stopped before turn-
ing the key to “OFF” or “LOCK”.
EAU01590
.
(Parking)
The steering is locked, and the tail-
light and auxiliary light are on, but all
other electrical systems are off. The
key can be removed.
The steering must be locked before
the key can be turned to “
.
”.
ECA00043
cCDo not use the parking position for
an extended length of time, other-
wise the battery may discharge.
EAU00027
INSTRUMENT AND CONTROL FUNCTIONS
3
ON
OFF
LOCK.
EAU00040
LOCK
The steering is locked, and all electri-
cal systems are off. The key can be
removed.
To lock the steering1. Turn the handlebars all the way
to the left.
2. Push the key in from the “OFF”
position, and then turn it to
“LOCK” while still pushing it.
3. Remove the key.
To unlock the steeringPush the key in, and then turn it to
“OFF” while still pushing it.
12
1. Push.
2. Turn.
4PT-E7 (English) 6/29/01 9:13 AM Page 14

3-4
INSTRUMENT AND CONTROL FUNCTIONS
3
EAU03890
Engine stop switch “$/#”Engine stop switchSet this switch to “#” before starting
the engine. Set this switch to “$” to
stop the engine in case of an emer-
gency, such as when the motorcycle
overturns or when the throttle cable is
stuck.
EAU00143
Start switch “,”Start switchPush this switch to crank the engine
with the starter.
EC000005
cCSee page 5-1 for starting instruc-
tions prior to starting the engine.
1
2
,
1. Engine stop switch “$/#”
2. Start switch “,”
EAU00152
Clutch leverClutch leverThe clutch lever is located at the left
handlebar grip. To disengage the
clutch, pull the lever toward the han-
dlebar grip. To engage the clutch,
release the lever. The lever should
be pulled rapidly and released slowly
for smooth clutch operation.
The clutch lever is equipped with a
clutch switch, which is part of the igni-
tion circuit cut-off system. (See page
3-12 for an explanation of the ignition
circuit cut-off system.)
1
1. Clutch lever
4PT-E7 (English) 6/29/01 9:13 AM Page 17

3-11
3. Tighten the locknut to the speci-
fied torque.
EC000018
cCAlways tighten the locknut against
the adjusting nut, and then tighten
the locknut to the specified torque.
EAU00315
wThis shock absorber contains
highly pressurized nitrogen gas.
For proper handling, read and
understand the following informa-
tion before handling the shock
absorber. The manufacturer can-
not be held responsible for proper-
ty damage or personal injury that
may result from improper han-
dling.
8Do not tamper with or attempt
to open the gas cylinder.
8Do not subject the shock
absorber to an open flame or
other high heat sources, other-
wise it may explode due to
excessive gas pressure.
8Do not deform or damage the
gas cylinder in any way, as
this will result in poor damp-
ing performance.
8Always have a Yamaha dealer
service the shock absorber.
EAU00330
SidestandSidestandThe sidestand is located on the left
side of the frame. Raise the side-
stand or lower it with your foot while
holding the motorcycle upright.NOTE:
The built-in sidestand switch is part of
the ignition circuit cut-off system,
which cuts the ignition in certain situ-
ations. (See further down for an
explanation of the ignition circuit cut-
off system.)
INSTRUMENT AND CONTROL FUNCTIONS
3Spring preload:
Minimum (soft):
Distance A = 1 mm
Standard:
Distance A = 5.5 mm
Maximum (hard):
Distance A = 12 mm
Tightening torque:
Locknut:
42 Nm (4.2 m
0kgf)
4PT-E7 (English) 6/29/01 9:13 AM Page 24

3-12
INSTRUMENT AND CONTROL FUNCTIONS
3
EW000044
wThe motorcycle must not be ridden
with the sidestand down, or if the
sidestand cannot be properly
moved up (or does not stay up),
otherwise the sidestand could con-
tact the ground and distract the
operator, resulting in a possible
loss of control. Yamaha’s ignition
circuit cut-off system has been
designed to assist the operator in
fulfilling the responsibility of rais-
ing the sidestand before starting
off. Therefore, check this system
regularly as described below and
have a Yamaha dealer repair it if it
does not function properly.
EAU03720
Ignition circuit cut-off
systemIgnition circuit cut-off systemThe ignition circuit cut-off system
(comprising the sidestand switch,
clutch switch and neutral switch) has
the following functions.
8It prevents starting when the
transmission is in gear and the
sidestand is up, but the clutch
lever is not pulled.
8It prevents starting when the
transmission is in gear and the
clutch lever is pulled, but the
sidestand is still down.
8It cuts the running engine when
the transmission is in gear and
the sidestand is moved down.
Periodically check the operation of
the ignition circuit cut-off system
according to the following procedure.
EW000045
wIf a malfunction is noted, have a
Yamaha dealer check the system
before riding.
4PT-E7 (English) 6/29/01 9:13 AM Page 25

4-3
PRE-OPERATION CHECKS
4
Chassis fasteners•Make sure that all nuts, bolts and screws are properly tightened.
•Tighten if necessary.—
Instruments, lights, signals
and switches•Check operation.
•Correct if necessary.3-1–3-4, 6-33–6-36
Sidestand switch•Check operation of ignition circuit cut-off system.
•If system is defective, have Yamaha dealer check vehicle.3-11–3-13 ITEM CHECKS PAGENOTE:
Pre-operation checks should be made each time the motorcycle is used. Such an inspection can be accomplished in a
very short time; and the added safety it assures is more than worth the time involved.
EWA00033
wIf any item in the Pre-operation check list is not working properly, have it inspected and repaired before operat-
ing the motorcycle.
4PT-E7 (English) 6/29/01 9:13 AM Page 30

1. Turn the fuel cock lever to “ON”.
2. Turn the key to “ON” and make
sure that the engine stop switch
is set to “#”.
3. Shift the transmission into the
neutral position.NOTE:
When the transmission is in the neu-
tral position, the neutral indicator light
should be on, otherwise have a
Yamaha dealer check the electrical
circuit.4. Turn the starter (choke) on and
completely close the throttle.
(See page 3-9 for starter (choke)
operation.)
5. Start the engine by pushing the
start switch.
5-1
EAU00372
OPERATION AND IMPORTANT RIDING POINTS
5
EAU00373
w8Become thoroughly familiar
with all operating controls and
their functions before riding.
Consult a Yamaha dealer
regarding any control or func-
tion that you do not thorough-
ly understand.
8Never start the engine or oper-
ate it in a closed area for any
length of time. Exhaust fumes
are poisonous, and inhaling
them can cause loss of con-
sciousness and death within a
short time. Always make sure
that there is adequate ventila-
tion.
8Before starting out, make sure
that the sidestand is up. If the
sidestand is not raised com-
pletely, it could contact the
ground and distract the opera-
tor, resulting in a possible loss
of control.
EAU03515
Starting the engineStarting the engineIn order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:
8The transmission is in the neutral
position.
8The transmission is in gear with
the clutch lever pulled and the
sidestand up.
EW000054
w8Before starting the engine,
check the function of the igni-
tion circuit cut-off system
according to the procedure
described on page 3-13.
8Never ride with the sidestand
down.
4PT-E7 (English) 6/29/01 9:13 AM Page 32

6-41
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU01008
TroubleshootingTroubleshootingAlthough Yamaha motorcycles
receive a thorough inspection before
shipment from the factory, trouble
may occur during operation. Any
problem in the fuel, compression, or
ignition systems, for example, can
cause poor starting and loss of
power.
The following troubleshooting chart
represents a quick and easy proce-
dure for checking these vital systems
yourself. However, should your
motorcycle require any repair, take it
to a Yamaha dealer, whose skilled
technicians have the necessary tools,
experience, and know-how to service
the motorcycle properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life
and can lead to expensive repair
bills. Tightening torque:
Axle nut:
105 Nm (10.5 m0kgf)
Brake caliper bracket bolt:
48 Nm (4.8 m0kgf)
Swingarm end bolt:
2.5 Nm (0.25 m0kgf)
4PT-E7 (English) 6/29/01 9:13 AM Page 78

6-42
PERIODIC MAINTENANCE AND MINOR REPAIR
6
1. Fuel
2. Compression
3. Ignition
4. Battery
Use electric starter.
There is compression.
Go to ignition check.
No compression.
Ask a Yamaha dealer to inspect.Wet.
Dry.Wipe clean with dry cloth and
Ask a Yamaha dealer to inspect.
Check if there is fuel
Enough fuel
No fuel
Go to compression check.Supply fuel.
in the fuel tank.
Remove sparkelectrodes. plug and checkOpen throttle half-way and start the
Engine doesn’t start, go to batterycheck.engine. correct spark gap or replace spark plug.
Engine turns over
Engine turns overBattery good.
Check connections
quickly.
slowly. or recharge.Engine doesn’t start, ask a Yamaha
dealer to inspect.
Engine doesn’t start, go to compression check.
Use the electric
starter.
EAU01397
Troubleshooting chartTroubleshooting chart
EW000125
wKeep away open flames and do not smoke while checking or working on the fuel system.
4PT-E7 (English) 6/29/01 9:13 AM Page 79

8-4
SPECIFICATIONS
8
Electrical
Ignition system T.C.I. (Digital)
Charging system
Type A.C. magneto
Standard output 14 V, 13.5A @ 5,000 rpm
Battery
Type YTX9-BS
Voltage, capacity 12 V, 8 AH
Headlight bulb typeHalogen bulb
Bulb voltage, wattage ×quantity
Headlight 12 V, 60/55W ×1
Tail/brake light 12 V, 5/21W ×1
Auxiliary light 12 V, 4W ×1
12 V, 3.4W ×1 (GB only)
Front flasher light 12 V, 21W ×2
Rear flasher light 12 V, 21W ×2
Meter lighting 12 V, 3.4W ×1
Neutral indicator light 12 V, 3.4W ×1
High beam indicator light 12 V, 3.4W ×1
Turn indicator light 12 V, 3.4W ×1
Fuse20A
4PT-E7 (English) 6/29/01 9:13 AM Page 91