light YAMAHA XT660Z 2009 Owner's Manual

PERIODIC MAINTENANCE AND MINOR REPAIR
6-8
1
2
3
4
5
6
7
8
9
10
2. Remove the spark plug as shown, with the spark plug wrench includ-
ed in the owner’s tool kit.
To check the spark plug 1. Check that the porcelain insulator around the center electrode of the
spark plug is a medium-to-light
tan (the ideal color when the vehi-
cle is ridden normally).
NOTE:
If the spark plug shows a distinctly dif-
ferent color, the engine could be oper-
ating improperly. Do not attempt to di-
agnose such problems yourself.
Instead, have a Yamaha dealer check
the vehicle.
2. Check the spark plug for elec- trode erosion and excessive car-
bon or other deposits, and re-
place it if necessary.
Specified spark plug:CR7E (NGK)
Spark plug gap:0.7-0.8 mm (0.028-0.032 in)
To install the spark plug
1. Measure the spark plug gap with a wire thickness gauge and, if
necessary, adjust the gap to
specification.
1. Spark plug gap

2. Clean the surface of the sparkplug gasket and its mating sur-
face, and then wipe off any grime
from the spark plug threads.
3. Install the spark plug with the spark plug wrench, and then tight-
en it to the specified torque.
EAU19603
Checking the spark plug
The spark plug is an important engine
component, which is easy to check.
Since heat and deposits will cause
any spark plug to slowly erode, the
spark plug should be removed and
checked in accordance with the peri-
odic maintenance and lubrication
chart. In addition, the condition of the
spark plug can reveal the condition of
the engine.
To remove the spark plug
1. Spark plug cap
2. Spark plug wrench
1. Remove the spark plug cap.

XT660Z 04-06 ING 11-03-2008 8:31 Pagina 6-8

1
2
3
4
5
6
7
8
9
10
PERIODIC MAINTENANCE AND MINOR REPAIR
6-9
EAUB1560
Engine oil and oil filter
element
The engine oil level should be checked
before each ride. In addition, the oil must
be changed and the oil filter element re-
placed at the intervals specified in the
periodic maintenance and lubrication
chart.
To check the engine oil level1. Place the vehicle on a level surface and hold it in an upright position.
NOTE:
Make sure that the vehicle is posi-
tioned straight up when checking the
oil level. A slight tilt to the side can re-
sult in a false reading.
2. Start the engine, warm it up for 10-15 minutes and then turn it off.
3. Remove the oil filler cap, wipe the dipstick clean, insert it back into
the oil filler hole (without screwing
it in), and then remove it again to
check the oil level.
1. Engine oil filler cap
2. Maximum level mark
3. Minimum level mark
NOTE:
●The engine oil tank is located in-
side of the frame.
●The engine oil should be between
the minimum and maximum level
marks.

Tightening torque:Spark plug:12.5 Nm (1.25 m·kgf, 9.0 ft·lbf)
NOTE:
If a torque wrench is not available
when installing a spark plug, a good
estimate of the correct torque is 1/4-
1/2 turn past finger tight. However, the
spark plug should be tightened to the
specified torque as soon as possible.
4. Install the spark plug cap.

XT660Z 04-06 ING 11-03-2008 8:31 Pagina 6-9

PERIODIC MAINTENANCE AND MINOR REPAIR
6-12
1
2
3
4
5
6
7
8
9
10
EAU20070
Coolant
The coolant level should be checked
before each ride. In addition, the
coolant must be changed at the inter-
vals specified in the periodic mainte-
nance and lubrication chart.
EAU20252
To check the coolant level 1. Place the vehicle on a level sur- face and hold it in an upright posi-
tion.
NOTE:
●The coolant level must be
checked on a cold engine since
the level varies with engine tem-
perature.
●Make sure that the vehicle is posi-
tioned straight up when checking
the coolant level. A slight tilt to the
side can result in a false reading.
2. Check the coolant level in the coolant reservoir.
ECA11620CAUTION:
● In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a
higher quality than specified. In
addition, do not use oils la-
beled “ENERGY CONSERVING
II” or higher.
● Make sure that no foreign ma-
terial enters the crankcase.
14. Start the engine, and then let it idle for several minutes while
checking it for oil leakage. If oil is
leaking, immediately turn the en-
gine off and check for the cause.
15. Turn the engine off, and then check the oil level and correct it if
necessary.
16. Install the engine guard by in- stalling the screws.
NOTE:
Be sure to wipe off spilled oil on any
parts after the engine and exhaust
system have cooled down.
Recommended engine oil:See page 8-1.
Oil quantity: Without oil filter element
replacement:2.50 L (2.64 US qt) (2.19 Imp.qt)
With oil filter element replacement: 2.60 L (2.73 US qt) (2.26 Imp.qt)
ECAM1060CAUTION:
The engine oil tank must be filled in
2 steps. First, fill the engine oil tank
with 1.90 L (2.0 US qt) (1.67 Imp.qt)
of the recommended engine oil.
Then, start the engine, race it 5 or 6
times, turn it off, and then add the
remainder of the engine oil.

XT660Z 04-06 ING 11-03-2008 8:31 Pagina 6-12

PERIODIC MAINTENANCE AND MINOR REPAIR
6-32
1
2
3
4
5
6
7
8
9
10
ECA10640CAUTION:
Do not use a fuse of a higher am-
perage rating than recommended
to avoid causing extensive damage
to the electrical system and possi-
bly a fire.
3. Turn the key to “ON” and turn on the electrical circuit in question to
check if the device operates.
4. If the fuse immediately blows again, have a Yamaha dealer
check the electrical system.
1. Parking lighting fuse
2. Signaling system fuse
3. Headlight fuse
4. Ignition fuse
5. Electronic fuel injection fuse
6. Radiator fan fuse
7. Backup fuse
8. Reserve fuses
The main fuse and fuse box are locat-
ed under the seat. (See page 6-31.)
If a fuse is blown, replace it as follows.1. Turn the key to “OFF” and turn off the electrical circuit in question.
2. Remove the blown fuse, and then install a new fuse of the specified
amperage.

7
8
654321
Specified fuses:
Main fuse:30 A
Parking lighting fuse: 10 A
Signalling system fuse: 10 A
Headlight fuse: 20 A
Ignition fuse: 10 A
Fuel injection system fuse: 10 A
Radiator fan fuse: 7.5 A
Backup fuse (for odometer,
clock and immobilizer): 10 A

XT660Z 04-06 ING 11-03-2008 8:31 Pagina 6-32

1
2
3
4
5
6
7
8
9
10
PERIODIC MAINTENANCE AND MINOR REPAIR
6-33
EAUB1580
Replacing a headlight bulb
1. Headlight bulb cover
1. Headlight coupler
2. Headlight bulb holder
3. Headlight bulb

EWA10790
WARNING0
Headlight bulbs get very hot. There-
fore, keep flammable products
away from a lit headlight bulb, and
do not touch the bulb until it has
cooled down.3. Place a new headlight bulb into position, and then secure it with
the bulb holder.
1. Do not touch this area

1. Headlight bulb holder
2. Headlight bulb
This model is equipped with quartz
bulb headlights. If a headlight bulb
burns out, replace it as follows.1. Remove the headlight bulb cover, and then disconnect the headlight
coupler.
2. Unhook the headlight bulb holder, and then remove the defective
bulb.

XT660Z 04-06 ING 11-03-2008 8:31 Pagina 6-33

PERIODIC MAINTENANCE AND MINOR REPAIR
6-34
1
2
3
4
5
6
7
8
9
10
ECA10650CAUTION:
Take care not to damage the fol-
lowing parts:
●Headlight bulb • Do not touch the glass part
of the headlight bulb to keep
it free from oil, otherwise the
transparency of the glass,
the luminosity of the bulb,
and the bulb life will be ad-
versely affected. Thoroughly
clean off any dirt and finger-
prints on the headlight bulb
using a cloth moistened with
alcohol or thinner.
●Headlight lens
• Do not affix any type of tinted
film or stickers to the head-
light lens.
• Do not use a headlight bulb
of a wattage higher than
specified.
4. Connect the coupler, and then in- stall the headlight bulb cover.
5. Have a Yamaha dealer adjust the headlight beam if necessary.
EAU24180
Tail/brake light
This model is equipped with an LED
type of tail/brake light.
If the tail/brake light does not come on,
have a Yamaha dealer check it.
EAU24202
Replacing a turn signal
light bulb
1. Screw
2. Turn signal light lens
3. Turn signal light bulb
1. Remove the turn signal light lensby removing the screw.
2. Remove the defective bulb by pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket, push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the screw.

XT660Z 04-06 ING 11-03-2008 8:31 Pagina 6-34

1
2
3
4
5
6
7
8
9
10
PERIODIC MAINTENANCE AND MINOR REPAIR
6-35
EAU42651
Replacing an auxiliary light
bulb
1. Auxiliary light socket
2. Auxiliary light bulb
This model is equipped with two auxil-
iary lights. If an auxiliary light bulb
burns out, replace it as follows.1. Remove panel G. (See page 6-7.)
2. Remove the auxiliary light socket (to- gether with the bulb) by pulling it out.
3. Remove the burnt out bulb by pulling it out.
4. Insert a new bulb into the socket.
5. Install the auxiliary light socket (together with the bulb) by push-
ing it in.
6. Install the panel.

EAUM2200
Replacing the license plate
light bulb
1. Bulb socket
2. License plate light bulb
1. Remove the socket (together with the bulb) by pulling it out.
2. Remove the defective bulb by pulling it out.
3. Insert a new bulb into the socket.
4. Install the socket (together with the bulb) by pushing it in.

ECA11190CAUTION:
Do not overtighten the screw, oth-
erwise the lens may break.

XT660Z 04-06 ING 11-03-2008 8:31 Pagina 6-35

MOTORCYCLE CARE AND STORAGE
7-1
1
2
3
4
5
6
7
8
9
10
EAU26000
Care
While the open design of a motorcycle
reveals the attractiveness of the tech-
nology, it also makes it more vulnera-
ble. Rust and corrosion can develop
even if high-quality components are
used. A rusty exhaust pipe may go un-
noticed on a car, however, it detracts
from the overall appearance of a mo-
torcycle. Frequent and proper care
does not only comply with the terms of
the warranty, but it will also keep your
motorcycle looking good, extend its
life and optimize its performance.
Before cleaning 1. Cover the muffler outlet with a plastic bag after the engine has
cooled down.
2. Make sure that all caps and cov- ers as well as all electrical cou-
plers and connectors, including
the spark plug cap, are tightly in-
stalled. 3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such prod-
ucts onto seals, gaskets, sprock-
ets, the drive chain and wheel
axles. Always rinse the dirt and
degreaser off with water.
Cleaning
ECA10770CAUTION:
●Avoid using strong acidic
wheel cleaners, especially on
spoked wheels. If such prod-
ucts are used on hard-to-re-
move dirt, do not leave the
cleaner on the affected area
any longer than instructed. Al-
so, thoroughly rinse the area
off with water, immediately dry
it, and then apply a corrosion
protection spray.
●Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use on-
ly a soft, clean cloth or sponge
with mild detergent and water
to clean plastic.
●Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.
●Do not use high-pressure
washers or steam-jet cleaners
since they cause water seep-
age and deterioration in the fol-
lowing areas: seals (of wheel
and swingarm bearings, fork
and brakes), electric compo-
nents (couplers, connectors,
instruments, switches and
lights), breather hoses and
vents.

XT660Z 07-10 ING 11-03-2008 8:33 Pagina 2

SPECIFICATIONS
8-3
1
2
3
4
5
6
7
8
9
10
Rear suspension:
Type: Swingarm (link suspension)
Spring/damper type: Coil spring/gas-oil damper, spring
preload adjustable
Wheel travel: 200 mm (7.87 in)
Electrical system:
Ignition system:Transistorized coil ignition (digital)
Charging system: A.C. magneto
Battery:
Model:GT9B-4
Voltage, capacity: 12 V, 8 Ah
Headlight:
Bulb type:Halogen bulb
Bulb voltage, wattage x quantity:Headlight:12 V, 55 W x 2
Auxiliary light: 12 V, 5 W x 2
Tail/brake light: LED
Front turn signal light: 12 V, 10 W x 2
Rear turn signal light: 12 V, 10 W x 2
Meter lighting: LED (backlight) Neutral indicator light:
LED
Turn signal indicator light: LED
High beam indicator light: LED
Coolant temperature warning light: LED
Engine trouble warning light: LED
Immobilizer system indicator light: LED
Fuses:Main fuse:
30 A
Headlight fuse: 20 A
Signaling system fuse: 10 A
Ignition fuse: 10 A
Parking lighting fuse: 10 A
Radiator fan fuse: 7.5 A
Fuel injection system fuse: 10 A
Backup fuse (for odometer, clock and immobilizer):
10 A

XT660Z 07-10 ING 11-03-2008 8:33 Pagina 8

1
2
3
4
5
6
7
8
9
10
INDEX
AAir filter element, cleaning the check hose....................................6-14
Air filter element, replacing ..............6-14
Anti-theft alarm (optional)...................3-8
Auxiliary light bulb, replacing............6-35
B Battery ..............................................6-30 To access the battery ...................6-30
To charge the battery....................6-30
To store the battery.......................6-31
Brake and clutch levers, checking and lubricating ...............6-26
Brake fluid ........................................6-22 Changing ......................................6-23
Checking fluid level .......................6-22
Brake lever .......................................3-11
Brake pads, checking .......................6-21
Brake pedal ......................................3-11 Lubricating ....................................6-27
C Cables, checking and lubricating .....6-25
Care and storage ...............................7-1
Catalytic converter ...........................3-13
Checking and lubricating the brake and clutch levers .................6-26
Checking and lubricating the brake pedal ...................................6-27
Checking and lubricating the cables ...........................................6-25 Checking and lubricating the
sidestand ......................................6-27
Checking and lubricating the throttle grip and cable ...................6-26
Checking the sidestand switch .........3-18
Clock mode ........................................3-7
Clutch lever ......................................3-10
Clutch lever free play, adjusting .......6-20
Consumer information ........................9-1
Controls and instruments ...................2-3
Function ..........................................3-1
Coolant .............................................6-12
Coolant temperature warning light .....3-4
D Description .........................................2-1 Controls and instrument .................2-3
Left view..........................................2-1
Right view .......................................2-2
Dimmer switch....................................3-9
Drive chain, cleaning and lubricating .....................................6-25
Drive chain slack ..............................6-23 Adjusting .......................................6-23
Checking .......................................6-23
Cleaning and lubricating ...............6-25
E Engine break-in ..................................5-3
Engine idling speed, adjusting .........6-15
Engine oil and oil filter element ..........6-9
Engine oil filter element....................6-10 Engine stop switch .............................3-9
Engine trouble warning light...............3-4
F Front fork ..........................................3-15 Adjusting .......................................3-15
Checking .......................................6-28
Front wheel ......................................6-36 Installing........................................6-37
Removing......................................6-36
Fuel ..................................................3-12
Fuel consumption, tips for reducing ...5-3
Fuel meter ..........................................3-7
Fuel tank breather hose ...................3-13
Fuel tank cap ...................................3-11
Fuses, replacing ...............................6-31
H Handlebar switches ............................3-9 Dimmer switch ................................3-9
Engine stop switch ..........................3-9
Hazard switch ...............................3-10
Horn switch .....................................3-9
Pass switch .....................................3-9
Start switch .....................................3-9
Turn signal switch ...........................3-9
Headlight bulb, replacing..................6-33
High beam indicator light ...................3-4
Horn switch ........................................3-9
I Identification numbers ........................9-1
Idling speed, checking .....................6-15

XT660Z 07-10 ING 11-03-2008 8:33 Pagina 1