brake YAMAHA YBR250 2011 Owner's Manual

PERIODIC MAINTENANCE AND ADJUSTMENT
6-31
64. Remove the axle nut, pull the
wheel axle out, and then remove
the wheel. NOTICE: Do not apply
the brake after the wheel has
been removed together with the
brake disc, otherwise the brake
pads will be forced shut.
[ECA11071]
EAUW0160
To install the front wheel
1. Lift the wheel up between the fork
legs.TIPMake sure that there is enough space
between the brake pads before insert-ing the brake disc into the caliper.
2. Insert the wheel axle.
3. Lower the front wheel so that it is
on the ground.
4. Tighten the wheel axle to the spec-
ified torque.
5. Tighten the front fork pinch bolt to
the specified torque.6. Push down hard on the handlebar
several times to check for proper
fork operation.
EAU25080
Rear wheel
EAU25431
To remove the rear wheel
WARNING
EWA10821
To avoid injury, securely support the
vehicle so there is no danger of itfalling over.
1. Loosen the axle nut and the brake
torque rod nut at the brake shoe
plate.
Tightening torque:
Wheel axle:
60 Nm (6.0 m·kgf, 44 ft·lbf)
Tightening torque:
Front fork pinch bolt:
55 Nm (5.5 m·kgf, 40 ft·lbf)
1. Drive chain slack adjusting nut
2. Brake torque rod
3. Locknut
4. Brake pedal free play adjusting nut
5. Axle nut
U5D1E1E0.book Page 31 Friday, September 5, 2008 1:17 PM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-32
6 2. Lift the rear wheel off the ground
according to the procedure on
page 6-30.
3. Disconnect the brake torque rod
from the brake shoe plate by re-
moving the nut and the bolt.
4. Remove the brake pedal free play
adjusting nut, and then disconnect
the brake rod at the brake cam-
shaft lever.
5. Loosen the locknut and the drive
chain adjusting nut on both ends of
the swingarm.
6. Remove the axle nut, and then pull
the wheel axle out.
7. Push the wheel forward, and then
remove the drive chain from the
rear sprocket.
TIPThe drive chain does not need to be
disassembled in order to remove andinstall the wheel.
8. Remove the wheel.
EAUW0170
To install the rear wheel
1. Insert the wheel axle from the left-
hand side, and then install the
drive chain onto the rear sprocket.
2. Install the axle nut.
3. Install the brake rod onto the brake
camshaft lever, and then install the
brake pedal free play adjusting
nut.
4. Connect the brake torque rod to
the brake shoe plate by installing
the bolt and the nut, and then tight-
en the nut to the specified torque.5. Adjust the drive chain slack. (See
page 6-19.)
6. Lower the rear wheel so that it is
on the ground.
7. Tighten the axle nut to the speci-
fied torque.
8. Adjust the brake pedal position
and free play. (See page 6-16.)
WARNING
EWA10660
After adjusting the brake pedal free
play, check the operation of thebrake light.
Tightening torque:
Brake torque rod nut:
49 Nm (4.9 m·kgf, 36 ft·lbf)
Tightening torque:
Axle nut:
104 Nm (10.4 m·kgf, 77 ft·lbf)
U5D1E1E0.book Page 32 Friday, September 5, 2008 1:17 PM

MOTORCYCLE CARE AND STORAGE
7-1
7
EAU26004
Care While the open design of a motorcycle
reveals the attractiveness of the tech-
nology, it also makes it more vulnera-
ble. Rust and corrosion can develop
even if high-quality components are
used. A rusty exhaust pipe may go un-
noticed on a car, however, it detracts
from the overall appearance of a motor-
cycle. Frequent and proper care does
not only comply with the terms of the
warranty, but it will also keep your
motorcycle looking good, extend its life
and optimize its performance.
Before cleaning
1. Cover the muffler outlet with a
plastic bag after the engine has
cooled down.
2. Make sure that all caps and covers
as well as all electrical couplers
and connectors, including the
spark plug cap, are tightly in-
stalled.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such prod-ucts onto seals, gaskets, sprock-
ets, the drive chain and wheel
axles. Always rinse the dirt and de-
greaser off with water.
Cleaning
NOTICE
ECA10772


Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the af-
fected area any longer than in-
structed. Also, thoroughly rinse
the area off with water, immedi-
ately dry it, and then apply a cor-
rosion protection spray.


Improper cleaning can damage
plastic parts (such as cowlings,
panels, windshields, headlight
lenses, meter lenses, etc.) and
the mufflers. Use only a soft,
clean cloth or sponge with wa-
ter to clean plastic. However, if
the plastic parts cannot be thor-
oughly cleaned with water, di-
luted mild detergent with water
may be used. Be sure to rinseoff any detergent residue using
plenty of water, as it is harmful
to plastic parts.


Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.


Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.


For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
U5D1E1E0.book Page 1 Friday, September 5, 2008 1:17 PM

MOTORCYCLE CARE AND STORAGE
7-2
7 Test the product on a small hid-
den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound after
washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea oron salt-sprayed roadsSince sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.
TIPSalt sprayed on roads in the winter mayremain well into spring.
1. Clean the motorcycle with cold wa-
ter and a mild detergent, after the
engine has cooled down.
NOTICE: Do not use warm water
since it increases the corrosive
action of the salt.
[ECA10791]
2. Apply a corrosion protection spray
on all metal, including chrome- and
nickel-plated, surfaces to prevent
corrosion.
After cleaning
1. Dry the motorcycle with a chamois
or an absorbing cloth.
2. Immediately dry the drive chain
and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally in-
duced discoloring of stainless-
steel exhaust systems can be re-
moved through polishing.)4. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal,
including chrome- and nickel-plat-
ed, surfaces.
5. Use spray oil as a universal clean-
er to remove any remaining dirt.
6. Touch up minor paint damage
caused by stones, etc.
7. Wax all painted surfaces.
8. Let the motorcycle dry completely
before storing or covering it.
WARNING
EWA11131
Contaminants on the brakes or tires
can cause loss of control.

Make sure that there is no oil or
wax on the brakes or tires.


If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or ac-
etone, and wash the tires with
warm water and a mild deter-
gent. Before riding at higher
speeds, test the motorcycle’s
braking performance and cor-nering behavior.
U5D1E1E0.book Page 2 Friday, September 5, 2008 1:17 PM

SPECIFICATIONS
8-2
8
5th:
23/27 (0.852)
Chassis:Frame type:
Double cradle
Caster angle:
26.50 °
Trail:
104.5 mm (4.11 in)Front tire:Type:
Tubeless
Size:
100/80-17M/C 52S
Manufacturer/model:
PIRELLI/SPORT DEMONRear tire:Type:
Tubeless
Size:
130/70-17M/C 62S
Manufacturer/model:
PIRELLI/SPORT DEMONLoading:Maximum load:
167 kg (368 lb)
(Total weight of rider, passenger, cargo and
accessories)Tire air pressure (measured on cold
tires):Loading condition:
0–90 kg (0–198 lb)
Front:
225 kPa (2.25 kgf/cm², 33 psi)Rear:
250 kPa (2.50 kgf/cm², 36 psi)
Loading condition:
90–167 kg (198–368 lb)
Front:
225 kPa (2.25 kgf/cm², 33 psi)
Rear:
250 kPa (2.50 kgf/cm², 36 psi)
Front wheel:Wheel type:
Cast wheel
Rim size:
17M/C x MT2.15Rear wheel:Wheel type:
Cast wheel
Rim size:
17M/C x MT3.00Front brake:Type:
Single disc brake
Operation:
Right hand operation
Recommended fluid:
DOT 3 or 4Rear brake:Type:
Drum brake
Operation:
Right foot operationFront suspension:Type:
Telescopic forkSpring/shock absorber type:
Coil spring/oil damper
Wheel travel:
120.0 mm (4.72 in)
Rear suspension:Type:
Swingarm (link suspension)
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
120.0 mm (4.72 in)Electrical system:Ignition system:
TCI (digital)
Charging system:
AC magnetoBattery:Model:
YTX7L-BS
Voltage, capacity:
12 V, 6.0 AhHeadlight:Bulb type:
Halogen bulbBulb voltage, wattage × quantity:Headlight:
12 V, 35 W/35.0 W × 1
Tail/brake light:
12 V, 5.0 W/21.0 W × 1
Front turn signal light:
12 V, 10.0 W × 2
Rear turn signal light:
12 V, 10.0 W × 2
U5D1E1E0.book Page 2 Friday, September 5, 2008 1:17 PM

INDEXAAir filter element, cleaning..................... 6-11
Auxiliary light bulb, replacing ................ 6-29BBattery................................................... 6-25
Brake and clutch levers, checking and
lubricating ........................................... 6-23
Brake and shift pedals, checking and
lubricating ........................................... 6-22
Brake fluid, changing ............................ 6-19
Brake fluid level, checking .................... 6-18
Brake lever .............................................. 3-6
Brake pads and shoes, checking .......... 6-17
Brake pedal ............................................. 3-7
Brake pedal position and free play,
adjusting ............................................. 6-16CCables, checking and lubricating .......... 6-21
Care ........................................................ 7-1
Catalytic converter .................................. 3-9
Clutch lever ............................................. 3-6
Clutch lever free play, adjusting ............ 6-15
Cowling and panels, removing and
installing................................................ 6-6DDimmer switch ........................................ 3-5
Display, multi-function ............................. 3-3
Drive chain, cleaning and lubricating .... 6-21
Drive chain slack ................................... 6-19EEngine break-in ....................................... 5-3
Engine idling speed............................... 6-12
Engine oil and oil filter element ............... 6-9
Engine stop switch .................................. 3-5Engine trouble warning light ................... 3-2
FFront fork, checking .............................. 6-24
Fuel......................................................... 3-8
Fuel consumption, tips for reducing........ 5-2
Fuel level warning light ........................... 3-2
Fuel tank cap .......................................... 3-7
Fuses, replacing ................................... 6-27HHandlebar switches ................................ 3-5
Headlight bulb, replacing ...................... 6-28
Helmet holder ....................................... 3-10
High beam indicator light ........................ 3-2
Horn switch ............................................. 3-5IIdentification numbers ............................ 9-1
Ignition circuit cut-off system ................ 3-13
Indicator and warning lights .................... 3-2LLuggage strap holders .......................... 3-12MMain switch/steering lock........................ 3-1
Maintenance and lubrication, periodic .... 6-3
Maintenance, emission control system... 6-2
Model label ............................................. 9-1NNeutral indicator light .............................. 3-2PParking ................................................... 5-3
Part locations .......................................... 2-1
Pass switch............................................. 3-5RRear brake light switch, adjusting ......... 6-17
Rear suspension, lubricating ................ 6-24
SSafety information ................................... 1-1
Seat ....................................................... 3-10
Shifting .................................................... 5-2
Shift pedal ............................................... 3-6
Shock absorber assemblies,
adjusting ............................................. 3-11
Sidestand .............................................. 3-12
Sidestand, checking and lubricating...... 6-23
Spark plug, checking ............................... 6-7
Specifications .......................................... 8-1
Speedometer........................................... 3-3
Starting the engine .................................. 5-1
Start switch.............................................. 3-5
Steering, checking................................. 6-25
Storage.................................................... 7-3
Storage compartment............................ 3-11
Supporting the motorcycle .................... 6-30TTachometer ............................................. 3-3
Throttle cable free play, checking ......... 6-12
Throttle grip and cable, checking and
lubricating ........................................... 6-22
Tires ...................................................... 6-13
Tool kit..................................................... 6-1
Troubleshooting .................................... 6-33
Troubleshooting chart ........................... 6-34
Turn signal indicator lights ...................... 3-2
Turn signal light bulb or tail/brake light
bulb, replacing .................................... 6-29
Turn signal switch ................................... 3-5VValve clearance..................................... 6-13
Vehicle identification number .................. 9-1
U5D1E1E0.book Page 1 Friday, September 5, 2008 1:17 PM