oil filter YAMAHA YBR250 2011 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2011, Model line: YBR250, Model: YAMAHA YBR250 2011Pages: 80, PDF Size: 4.9 MB
Page 6 of 80
TABLE OF CONTENTSSAFETY INFORMATION ..................1-1
DESCRIPTION ..................................2-1
Left view ..........................................2-1
Right view ........................................2-2
Controls and instruments.................2-3
INSTRUMENT AND CONTROL
FUNCTIONS.......................................3-1
Main switch/steering lock ................3-1
Indicator and warning lights ............3-2
Speedometer ..................................3-3
Tachometer ....................................3-3
Multi-function display ......................3-3
Handlebar switches ........................3-5
Clutch lever .....................................3-6
Shift pedal .......................................3-6
Brake lever .....................................3-6
Brake pedal ....................................3-7
Fuel tank cap ..................................3-7
Fuel .................................................3-8
Catalytic converter ..........................3-9
Seat ..............................................3-10
Helmet holder ...............................3-10
Storage compartment ...................3-11
Adjusting the shock absorber
assemblies ................................3-11
Luggage strap holders ..................3-12
Sidestand ......................................3-12
Ignition circuit cut-off system ........3-13FOR YOUR SAFETY –
PRE-OPERATION CHECKS............. 4-1
OPERATION AND IMPORTANT
RIDING POINTS................................. 5-1
Starting the engine ......................... 5-1
Shifting ........................................... 5-2
Tips for reducing fuel
consumption ............................... 5-2
Engine break-in .............................. 5-3
Parking ........................................... 5-3
PERIODIC MAINTENANCE AND
ADJUSTMENT................................... 6-1
Owner’s tool kit ............................... 6-1
Periodic maintenance chart for
the emission control system ....... 6-2
General maintenance and
lubrication chart .......................... 6-3
Removing and installing the
cowling and panels ..................... 6-6
Checking the spark plug ................. 6-7
Engine oil and oil filter element ...... 6-9
Cleaning the air filter element ...... 6-11
Adjusting the engine idling
speed ........................................ 6-12
Checking the throttle cable free
play ........................................... 6-12
Valve clearance ............................ 6-13
Tires ............................................. 6-13
Cast wheels .................................. 6-15Adjusting the clutch lever free
play ........................................... 6-15
Adjusting the brake pedal position
and free play ............................. 6-16
Adjusting the rear brake light
switch ....................................... 6-17
Checking the front brake pads
and rear brake shoes ............... 6-17
Checking the front brake fluid
level .......................................... 6-18
Changing the brake fluid .............. 6-19
Drive chain slack .......................... 6-19
Cleaning and lubricating the
drive chain ................................ 6-21
Checking and lubricating the
cables ....................................... 6-21
Checking and lubricating the
throttle grip and cable ............... 6-22
Checking and lubricating the
brake and shift pedals .............. 6-22
Checking and lubricating the
brake and clutch levers ............ 6-23
Checking and lubricating the
sidestand .................................. 6-23
Lubricating the rear suspension ... 6-24
Checking the front fork ................. 6-24
Checking the steering .................. 6-25
Checking the wheel bearings ....... 6-25
Battery ......................................... 6-25
Replacing the fuses ..................... 6-27
Replacing the headlight bulb ....... 6-28U5D1E1E0.book Page 1 Friday, September 5, 2008 1:17 PM
Page 13 of 80
DESCRIPTION
2-2
2
EAU10420
Right view1. Owner’s tool kit (page 6-1)
2. Air filter element (page 6-11)
3. Front brake fluid reservoir (page 6-18)
4. Engine oil filter element (page 6-9)
5. Engine oil filler cap (page 6-9)
6. Brake pedal (page 3-7)
7. Shock absorber assembly spring preload adjusting ring (page 3-11)
U5D1E1E0.book Page 2 Friday, September 5, 2008 1:17 PM
Page 33 of 80
OPERATION AND IMPORTANT RIDING POINTS
5-3
5
EAU16841
Engine break-in There is never a more important period
in the life of your engine than the period
between 0 and 1600 km (1000 mi). For
this reason, you should read the follow-
ing material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1600 km (1000 mi). The various parts in
the engine wear and polish themselves
to the correct operating clearances.
During this period, prolonged full-throt-
tle operation or any condition that might
result in engine overheating must be
avoided.
EAU17101
0–1000 km (0–600 mi)
Avoid prolonged operation above 5000
r/min. NOTICE: After 1000 km (600
mi) of operation, the engine oil must
be changed, and the oil filter ele-
ment replaced.
[ECA11151]
1000–1600 km (600–1000 mi)
Avoid prolonged operation above 6000
r/min.1600 km (1000 mi) and beyond
The vehicle can now be operated nor-
mally.
NOTICE
ECA10310
Keep the engine speed out of
the tachometer red zone.
If any engine trouble should oc-
cur during the engine break-in
period, immediately have a
Yamaha dealer check the vehi-cle.
EAU17213
Parking When parking, stop the engine, and
then remove the key from the main
switch.
WARNING
EWA10311
Since the engine and exhaust
system can become very hot,
park in a place where pedestri-
ans or children are not likely to
touch them and be burned.
Do not park on a slope or on soft
ground, otherwise the vehicle
may overturn, increasing the
risk of a fuel leak and fire.
Do not park near grass or other
flammable materials whichmight catch fire.
U5D1E1E0.book Page 3 Friday, September 5, 2008 1:17 PM
Page 37 of 80
PERIODIC MAINTENANCE AND ADJUSTMENT
6-4
6
10 Drive chainCheck chain slack, alignment and
condition.
Adjust and lubricate chain with a
special O-ring chain lubricant
thoroughly.Every 500 km (300 mi) and after washing the motorcycle or riding in the rain
11*Steering bearingsCheck bearing play and steering
for roughness.√√√√√
Lubricate with lithium-soap-based
grease.Every 20000 km (12000 mi)
12*Chassis fastenersMake sure that all nuts, bolts and
screws are properly tightened.√√√√√
13 SidestandCheck operation.
Lubricate.√√√√√
14*Sidestand switchCheck operation.√√√√√√
15*Front forkCheck operation and for oil leak-
age.√√√√
16*Shock absorber as-
sembliesCheck operation and shock ab-
sorbers for oil leakage.√√√√
17*Rear suspension re-
lay arm and con-
necting arm
pivoting pointsCheck operation.√√√√
Lubricate with lithium-soap-based
grease.√√
18 Engine oilChange.
Check oil level and vehicle for oil
leakage.√√√√√√
19Engine oil filter ele-
mentReplace.√√√ NO. ITEM CHECK OR MAINTENANCE JOBODOMETER READING
ANNUAL
CHECK 1000 km
(600 mi)10000 km
(6000 mi)20000 km
(12000 mi)30000 km
(18000 mi)40000 km
(24000 mi)
U5D1E1E0.book Page 4 Friday, September 5, 2008 1:17 PM
Page 42 of 80
PERIODIC MAINTENANCE AND ADJUSTMENT
6-9
6
EAU37804
Engine oil and oil filter ele-
ment The engine oil level should be checked
before each ride. In addition, the oil
must be changed and the oil filter ele-
ment replaced at the intervals specified
in the General periodic maintenance
and lubrication chart.
To check the engine oil level
1. Place the vehicle on a level sur-
face and hold it in an upright posi-
tion. A slight tilt to the side can
result in a false reading.
2. Start the engine, warm it up for
several minutes, and then turn it
off.
3. Wait a few minutes until the oil set-
tles, and then check the oil level
through the check window located
at the bottom-right side of the
crankcase.TIPThe engine oil should be between theminimum and maximum level marks.4. If the engine oil is below the mini-
mum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.
To change the engine oil (with or
without oil filter element replace-
ment)
1. Place the vehicle on a level sur-
face.
2. Start the engine, warm it up for
several minutes, and then turn it
off.
3. Place an oil pan under the engine
to collect the used oil.4. Remove the engine oil filler bolt
and drain bolt to drain the oil from
the crankcase.
TIPCheck the washer for damage and re-place it if necessary.
1. Engine oil filler cap
2. Maximum level mark
3. Minimum level mark
1. Dipstick
1. Engine oil drain bolt
U5D1E1E0.book Page 9 Friday, September 5, 2008 1:17 PM
Page 43 of 80
PERIODIC MAINTENANCE AND ADJUSTMENT
6-10
6 5. Remove the oil filter element drain
bolt to drain the oil from the oil filter
element.
TIPSkip steps 6–8 if the oil filter element isnot being replaced.
6. Remove the oil filter element cover
by removing the bolts.7. Remove and replace the oil filter
element and O-rings.
TIPMake sure that the O-rings are properlyseated.
8. Install the oil filter element cover by
installing the bolts, then tightening
them to the specified torque.
9. Install the engine oil drain bolt, and
then tighten it to the specified
torque.10. Install the oil filter element drain
bolt, and then tighten it to the spec-
ified torque.
11. Refill with the specified amount of
the recommended engine oil, and
then install and tighten the oil filler
bolt.
TIPBe sure to wipe off spilled oil on any
parts after the engine and exhaust sys-tem have cooled down.
1. Oil filter element cover bolt
2. Oil filter element drain bolt
1. Oil filter element
2. O-ring
Tightening torque:
Oil filter element cover bolt:
10 Nm (1.0 m·kgf, 7.4 ft·lbf)
Tightening torques:
Engine oil drain bolt:
20 Nm (2.0 m·kgf, 15 ft·lbf)
Oil filter element drain bolt:
7 Nm (0.7 m·kgf, 5.25 ft·lbf)
Recommended oil:
See page 8-1.
Oil quantity:
Without oil filter element replace-
ment:
1.35 L (1.43 US qt, 1.19 Imp.qt)
With oil filter element replacement:
1.45 L (1.53 US qt, 1.28 Imp.qt)
U5D1E1E0.book Page 10 Friday, September 5, 2008 1:17 PM
Page 44 of 80
PERIODIC MAINTENANCE AND ADJUSTMENT
6-11
6
NOTICE
ECA11620
In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a high-
er quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
Make sure that no foreign mate-rial enters the crankcase.
12. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking, im-
mediately turn the engine off and
check for the cause.
13. Turn the engine off, and then
check the oil level and correct it if
necessary.
EAU20881
Cleaning the air filter element The air filter should be cleaned at the
specified intervals. It should be cleaned
more frequently when riding in unusual-
ly wet or dusty areas.
1. Remove panel B. (See page 6-6.)
2. Remove the air filter case by re-
moving the screws.
3. Remove the air filter from the case.4. Remove the air filter element from
its guide and clean it with solvent.
After cleaning, remove the remain-
ing solvent by squeezing the ele-
ment.1. Air filter case cover
2. Screw
1. Air filter element
1
U5D1E1E0.book Page 11 Friday, September 5, 2008 1:17 PM
Page 45 of 80
PERIODIC MAINTENANCE AND ADJUSTMENT
6-12
6 5. Apply recommended oil to the en-
tire surface of the element and
squeeze out the excess oil. It
should be wet but not dripping.
6. Insert the air filter element guide
into the air filter and install it in the
case. NOTICE: Make sure that
the air filter element is properly
seated in the air filter case. The
engine should never be operat-
ed without the air filter element
installed, otherwise the pis-
ton(s) and/or cylinder(s) may
become excessively worn.
[ECA10481]
7. Install the air filter case cover and
panel by installing the screws.
EAU34301
Adjusting the engine idling
speed The engine idling speed must be
checked and, if necessary, adjusted as
follows at the intervals specified in the
periodic maintenance and lubrication
chart.
The engine should be warm before
making this adjustment.
Check the engine idling speed and, if
necessary, adjust it to specification by
turning the idle adjusting screw. To in-
crease the engine idling speed, turn the
screw in direction (a). To decrease the
engine idling speed, turn the screw in
direction (b).TIPIf the specified idling speed cannot be
obtained as described above, have aYamaha dealer make the adjustment.
EAU21382
Checking the throttle cable
free play The throttle cable free play should mea-
sure 3.0–5.0 mm (0.12–0.20 in) at the
throttle grip. Periodically check the
throttle cable free play and, if neces-
sary, have a Yamaha dealer adjust it.
Recommended oil:
Engine oil
Engine idling speed:
1300–1500 r/min
1. Throttle cable free play
U5D1E1E0.book Page 12 Friday, September 5, 2008 1:17 PM
Page 72 of 80
SPECIFICATIONS
8-1
8
Dimensions:Overall length:
2025 mm (79.7 in)
Overall width:
745 mm (29.3 in)
Overall height:
1065 mm (41.9 in)
Seat height:
805 mm (31.7 in)
Wheelbase:
1360 mm (53.5 in)
Ground clearance:
190 mm (7.48 in)
Minimum turning radius:
2395 mm (94.3 in)Weight:With oil and fuel:
154.0 kg (340 lb)Engine:Engine type:
Air cooled 4-stroke, SOHC
Cylinder arrangement:
Forward-inclined single cylinder
Displacement:
249.0 cm³
Bore × stroke:
74.0 × 58.0 mm (2.91 × 2.28 in)
Compression ratio:
9.80 :1
Starting system:
Electric starter
Lubrication system:
Wet sump
Engine oil:Type:
SAE 20W-40 or 20W-50
Recommended engine oil grade:
API service SF, SG type or higher, JASO
standard MA
Engine oil quantity:
Without oil filter element replacement:
1.35 L (1.43 US qt, 1.19 Imp.qt)
With oil filter element replacement:
1.45 L (1.53 US qt, 1.28 Imp.qt)Air filter:Air filter element:
Wet elementFuel:Recommended fuel:
Regular unleaded gasoline only
Fuel tank capacity:
19.2 L (5.07 US gal, 4.22 Imp.gal)
Fuel reserve amount:
4.5 L (1.19 US gal, 0.99 Imp.gal)
Fuel injection:Throttle body:
Type/quantity:
33EHS-3D01/1Spark plug (s):Manufacturer/model:
NGK/DR8EA
Spark plug gap:
0.6–0.7 mm (0.024–0.028 in)Clutch:Clutch type:
Wet, multiple-discTransmission:Primary reduction system:
Spur gear
Primary reduction ratio:
74/24 (3.083)
Secondary reduction system:
Chain drive
Secondary reduction ratio:
44/15 (2.933)
Transmission type:
Constant mesh 5-speed
Operation:
Left foot operation
Gear ratio:
1st:
36/14 (2.571)
2nd:
32/19 (1.684)
3rd:
28/22 (1.273)
4th:
26/25 (1.040)
-20 -10 0
10 20 30
40
50 ˚C
SAE 10W-30
SAE 15W-40SAE 20W-40SAE 20W-50
SAE 10W-40SAE 10W-50
U5D1E1E0.book Page 1 Friday, September 5, 2008 1:17 PM
Page 76 of 80
INDEXAAir filter element, cleaning..................... 6-11
Auxiliary light bulb, replacing ................ 6-29BBattery................................................... 6-25
Brake and clutch levers, checking and
lubricating ........................................... 6-23
Brake and shift pedals, checking and
lubricating ........................................... 6-22
Brake fluid, changing ............................ 6-19
Brake fluid level, checking .................... 6-18
Brake lever .............................................. 3-6
Brake pads and shoes, checking .......... 6-17
Brake pedal ............................................. 3-7
Brake pedal position and free play,
adjusting ............................................. 6-16CCables, checking and lubricating .......... 6-21
Care ........................................................ 7-1
Catalytic converter .................................. 3-9
Clutch lever ............................................. 3-6
Clutch lever free play, adjusting ............ 6-15
Cowling and panels, removing and
installing................................................ 6-6DDimmer switch ........................................ 3-5
Display, multi-function ............................. 3-3
Drive chain, cleaning and lubricating .... 6-21
Drive chain slack ................................... 6-19EEngine break-in ....................................... 5-3
Engine idling speed............................... 6-12
Engine oil and oil filter element ............... 6-9
Engine stop switch .................................. 3-5Engine trouble warning light ................... 3-2
FFront fork, checking .............................. 6-24
Fuel......................................................... 3-8
Fuel consumption, tips for reducing........ 5-2
Fuel level warning light ........................... 3-2
Fuel tank cap .......................................... 3-7
Fuses, replacing ................................... 6-27HHandlebar switches ................................ 3-5
Headlight bulb, replacing ...................... 6-28
Helmet holder ....................................... 3-10
High beam indicator light ........................ 3-2
Horn switch ............................................. 3-5IIdentification numbers ............................ 9-1
Ignition circuit cut-off system ................ 3-13
Indicator and warning lights .................... 3-2LLuggage strap holders .......................... 3-12MMain switch/steering lock........................ 3-1
Maintenance and lubrication, periodic .... 6-3
Maintenance, emission control system... 6-2
Model label ............................................. 9-1NNeutral indicator light .............................. 3-2PParking ................................................... 5-3
Part locations .......................................... 2-1
Pass switch............................................. 3-5RRear brake light switch, adjusting ......... 6-17
Rear suspension, lubricating ................ 6-24
SSafety information ................................... 1-1
Seat ....................................................... 3-10
Shifting .................................................... 5-2
Shift pedal ............................................... 3-6
Shock absorber assemblies,
adjusting ............................................. 3-11
Sidestand .............................................. 3-12
Sidestand, checking and lubricating...... 6-23
Spark plug, checking ............................... 6-7
Specifications .......................................... 8-1
Speedometer........................................... 3-3
Starting the engine .................................. 5-1
Start switch.............................................. 3-5
Steering, checking................................. 6-25
Storage.................................................... 7-3
Storage compartment............................ 3-11
Supporting the motorcycle .................... 6-30TTachometer ............................................. 3-3
Throttle cable free play, checking ......... 6-12
Throttle grip and cable, checking and
lubricating ........................................... 6-22
Tires ...................................................... 6-13
Tool kit..................................................... 6-1
Troubleshooting .................................... 6-33
Troubleshooting chart ........................... 6-34
Turn signal indicator lights ...................... 3-2
Turn signal light bulb or tail/brake light
bulb, replacing .................................... 6-29
Turn signal switch ................................... 3-5VValve clearance..................................... 6-13
Vehicle identification number .................. 9-1
U5D1E1E0.book Page 1 Friday, September 5, 2008 1:17 PM