oil YAMAHA YD110 2005 User Guide

b. Unscrew the dipstick and rest it
on the threads of the oil filler hole.
The oil level should be between
the minimum and maximum
mark on the dipstick. If the level
is low, add oil to raise it to the
specified level.ch- fMikfLVd d¨ [k¨y ysa v©j bls
fQyj ds Nsn ij fVdk nsaA vkW;y
dk ysoy fMikfLVd ds fuEure o
mPpre fu'kku ds e/; esa g¨uk pkfg,A
;fn ysoy de yxs r¨ bls c<+kus ds
fy, fu£n"V Lrj rd rsy MkysaA
1. Dipstick
fMifLVd
2. Engine oil replacement
batu&rsy d¨ cnyuk
a. Warm up the engine for a few
minutes.
dqN feuV¨ ds fy, batu d¨ xeZ
djsaA
b. Stop the engine. Place an oil pan
under the engine and remove
the dipstick.
batu d¨ can dj nsA batu ds uhps
,d vkW;y iSu ¼crZu½ j[k ysa rFkk
fMikfLVd d¨ ckgj fudky ysaA
batu dh vf/kd dk;Z{kerk rFkk nh?kZ thou ds fy, batu&vkW;y d¨ ges'kk çLrkfor
varjky¨ ij cnyrs jgsaA
6.12
PERIODIC MAINTENANCE AND MINOR REPAIRlkef;d j[kj[kko rFkk ekewyh ejEer
1
PG1_55.pmd2/25/2005, 10:04 AM 48

1. Engine oil drain plug
batu vkW;y Mªsu Iyx
c. Remove the drain plug and drain
the oil.
Mªsu Iyx dks [kksy dj ckgj fudky
ysa v©j rsy dks fudyus nsaA
d. Reinstall the drain plug and
tighten it to the specified torque.
Mªsu Iyx dks fQj ls yxk nsa v©j bls
fu£n"V VkdZ rd dl nsaaA
f. Start the engine and warm up for
a few minutes. While warming
up, check for oil leakage. If oil
leakage is found, stop the engine
immediately and check for the
cause.
batu dks pkyw djsa v©j dqN feuVksa
ds fy, FkksM+k xeZ djrs le; rsy ds
fjlko dh tk¡p dj ysaA ;fn rsy
*yhd^ dj jgk gks rks batu dks rqjar
can dj nsa vkSj dkj.k dh tk¡p djsaA
ALWAYS CHANGE ENGINE OIL AT RECOMMENDED GRADE OF ENGINE OIL
ges'kk dsoy çLrkfod xzsM dk batu&vkW;y gh ç;ksx djsaA
e. Fill engine with oil and install the
dipstick.
batu dks rsy ls Hkj ysa v©j fMikfLVd
dks mlesa yxk nsaA
Tightening torque
dlk x;k VkdZ %
Drain plug
Mªsu Iyx %
14.5 Lt.-lb (2.0 m-kg)
Recommended oil:
YAMALUBE 4 stroke motor oil
(20 W 40 type SG) or equivalent.
Oil quantity:
Total amount : 1.1 L
Periodic oil change :0.9 L
6.13
çLrkfod rsy %
;kekY;wc&
4 LVªksd eksVj vkW;y
¼
20
M~CY;w
40
Vkbi ,l th½ vFkok
mlds leku½
rsy dh ek=kk %
dqy ek=kk %
1.1
fyñ
le;≤ ij rsy esa
ifjorZu %
0.9
fyñ
PERIODIC MAINTENANCE AND MINOR REPAIR
lkef;d j[kj[kko rFkk ekewyh ejEer
1
PG1_55.pmd2/25/2005, 10:04 AM 49

CAUTION :
Make sure the air filter is
properly seated in the air filter
case.
 The engine should never be run
without the air filter installed.
Excessive piston and/or
cylinder wear may result.
 Dirty Element Air Cleaner
caused excessive fuel
consumption and loss of
power.
 Clean Element Air Cleaner after
every 2000 kms.
 The Element Air Cleaner should
be cleaned and lubricated more
frequently (every 1000 km,s), if
Motorcycle is operated in very
dusty (e.g. unpaved, dust laden
roads) conditions. lko/kkuh %
;g lqfufpr djsa fd ,;j&fQYVj
lgh tk,A
6. Apply recommended oil to the
entire surface of the each
element and squeeze out the
excess oil. They should be wet
but not dripping.
çR;sd ewy Hkkx dh van#uh lrg ij
çLrkfod rsy gh yxk, v©j Qkyrw
rsy ds fupksM+ ysA os ¼ewy Hkkx½ xhys
gksus pkfg, u fd rsy esa Mwcs gq,A
Recommended oil
çLrkfod rsy :20W40 type SG
7. Pull the air filter elements over
the frame and install the air filter
in the case.
,;j&fQYVj ds ,yhesaV ¼ewy&fgLlksa½
dks Ýse ds Åij ls [khap ys rFkk
,;j&fQYVj dks dsl ds vanj yxk
nsaA
8. Install the Spring Wire.
¯Lçx okW;j Hkh yxk,¡A
9. Install the air filter case cover and
panel
,;j&fQYVj dsl ds doj v©j iSuy
dks yxk nsaA
6.15
PERIODIC MAINTENANCE AND MINOR REPAIR
lkef;d j[kj[kko rFkk ekewyh ejEer
PG1_55.pmd2/25/2005, 10:04 AM 51

psrkouh
,fDly uV ds fy, ges'kk u, dkWVj fiu
dk gh ç;¨x djsaA7. Adjust the free play in the brake
pedal.
czsd iSMy ds Ýh Iys d¨ ,MtLV
djsaA
p
WARNINGCheck the operation of the brake
light after adjusting the rear brake. psrkouhfiNyh czsd d¨ ,MtLV djus ds ckn
czsd dh cÙkh ¼ykbV½ dh çfØ;k d¨ tk¡p
ysaA
6.28
Drive chain lubricationMªkbo&psu dh Y;wczhds'kuThe chain consists of many parts
which work with each other. If the
chain is not maintained properly, it
will wear out quickly. Therefore, the
chain must be serviced regularly.
This service is especially
necessary when riding in dusty
areas.psu esa cgqr ls fgLls g¨rs gS t¨ ,d&nwljs
ds fy, dke djrs gSA ;fn psu dh
ns[kHkky lgh rjg ls u dh tk, r¨ ;g
tYnh f?kl tkrh gSA blfy, yxkrkj
bldh l£ol dk /;ku j[kuk pkfg,A
jsrhys bykd¨ esa e¨Vj&lkbZfdy pykrs
le; bl rjg dh l£ol djkuk cgqr
t#jh g¨ tkrk gSA1. The drive chain should be
lubricated every 5,000 km.
Mªkbo&psu d¨ çR;sd
5,000
fdñehñ
ds ckn Y;wczhdsV dj nsuh pkfg,A
2. To clean the chain thoroughly,
remove it from the Motorcycle,
dip it in solvent, and clean outas much dirt as possible.
Then, take the chain out of the
solvent to dry it, and then dip
the chain in oil of 20W40.
Remove the chain and hang it
on a peg for a while till the
excess oil drips down
completely. Then using a clean
cloth wipe the chain.
psu d¨ iw.kZr;k lkQ djus ds fy,
bls e¨Vj&lkbZfdy ls mrkj ysa] ækod
¼lkWyosaV½ esa Mqc¨ nsa v©j ftruk T;knk
laHko g¨ /kwy&feêh d¨ lkQ dj ysaA
mlds ckn psu d¨ lq[kkus ds fy,
ækod ls ckgj fudky ysa v©j fQj ls20W40
czkaM ds ¼vkW;y½ rsy esa iwjh
fHkx¨ nsaA rRi'pkr~ psu d¨ ckgj
fudky dj rc rd [kq¡Vh ij Vk¡x nsa]
tc rd fd Qkyrw rsy blesa ls iwjh
rjg fupqM+ u tk,A rc psu d¨ ,d
lkQ diM+s ls i¨aN ysaA
PERIODIC MAINTENANCE AND MINOR REPAIRlkef;d j[kj[kko rFkk ekewyh ejEer
pg56_96.pmd2/25/2005, 9:59 AM 64

Throttle cable and grip
lubricationFkzkWVy dscy v©j fxzi Y;wczhdsV
djukAThe throttle twist grip assembly
should be greased at the time that
the cable is lubricated, since the
grip must be removed to get at the
end of the throttle cable. After
removing the screws, hold the end
of the cable up in the air and put in
several drops of lubricant. With the
throttle grip disassembled, coat the
metal surface of the grip assembly
with a suitable all purpose grease.ftl le; dscy dks Y;wczhdsaV fd;k tkrk
gS mlh le; ^FkzkWVy V~foLV fxzi vlsEcyh*rkj¨a d¨ tax&çfrj¨/kh rsy rFkk dscy ds
fdukj¨a ls yqczhdsV djsaA ;fn dscy lgh
rjhds ls dke ugh dj jgh g¨ r¨ okbZñ,eñvkbZñ
Mhyj ls bls cnyrs d¨ dgsaA
dh fxzlhax Hkh dh tkuh pkfg,] D;ksafd
fxzi dks FkzkVy dh dscy ds fljs rd ykus
ds fy,] bls ckgj fudky ysuk pkfg,A
isap gVkus ds ckn rkj ¼dscy½ ds ,d
fljs ¼fdukjs½ dks gok esa idM+s jgsa vkSj
ml ij Y;wczhdsaV dh cgqr lh cwansa MkysaA
FkzkWVy fxzi dks [kksyus ¼vyx&vyx djus½
ds lkFk fxzi vlsEcyh dks /kkrq ds ry ij
;Fkk;ksX;] cgqmís'kh; ¼vkWy ijit+½ xzhl
dh dks¯Vx dj nsaA
Cable inspection and
lubricationdscy dk fujh{k.k ,oa Y;wczhds'ku WARNINGDamage to the outer housing of
cables may lead to internal
rusting and interfere with the
cable movement. Replace
damaged cables as soon as
possible to prevent unsafe
conditions. psrkouhdscy ¼rkj¨a½ dh ckgjh gkůlx ds
{kfrxzLr g¨us ls ;g vanj ls tax idM+
ldrh gS v©j blls dscy d¨ Åij uhps
ewoesaV djus esa eqf'dy vk ldrh gSA
vlqjf{kr fLFkfr;¨a ¼gkykr¨aa½ ls cpus ds
fy, {kfrxzLr rkj¨a ¼dscy½ d¨ ftruh
tYnh g¨ lds cny nsaALubricate the cables and cable
ends with anticorrosive oil . If a
cable does not operate smoothly,
ask a YMI dealer to replace it.Recommended lubricant
çLrkfod yqczhdsVj %20W40 Type SG
6.29
PERIODIC MAINTENANCE AND MINOR REPAIR
lkef;d j[kj[kko rFkk ekewyh ejEer
pg56_96.pmd2/25/2005, 9:59 AM 65

Front fork inspectionÝaV QksdZ dk fujh{k.k WARNINGSecurely support the Motorcycle
so there is no danger of it falling
over. psrkouhlqjf{kr rjhds ls eksVjlkbfdy dks lgkjk
nsa] ftlls blds fxjus dk [krjk u jgssA1. Visual check
Check for scratches or
damage on the inner tube and
traces if oil leakage from the
front fork.
n f"Vxr ¼us=kh;½ tk¡p %
vkxs yxs QksdZ esa ls vR;f/kd rsy
fjlko vkSj vanj dh V~;wc ij [kjksapks
rFkk blds {kfrxzLr gksus dh tk¡p
djsaA
2. Operation check
Place the Motorcycle on a level
place.
izfØ;k dh tk¡p %
eksVjlkbfdy dks ,d ysoy fd;s gq,
¼likV½ LFkku ij [kM+k djsaA
a. Hold the Motorcycle in an
upright position and apply the
front brake.
eksVjlkbfdy dks lh/kk Åij mBkdj
j[ksa vkSj vxyh czsd dk mi;ksx djsaA
b. Push down hard on the
handlebars several times and
check if the fork bounds
smoothly.
gSafMyckjksa dk dbZ ckj tksj ls uhps
dh vksj nck,a vkSj bl ckr dh tk¡p
djsa fd D;k QksdZ vkjke ls ^mNky*
ys ysrk gSA
6.31

WARNING
If the center and/or sidestand does
not move smoothly, consult a YMI
dealer. psrkouh;fn eksVjlkbfdy ds chp okyk rFkk
lkbM dk LVS.M vkjke ls ¼fcuk fdlh
:dkoV½ ds dke ugha djrs gksa rks
okbZñ,eñvkbZñ Mhyj ls laidZ djsaA
PERIODIC MAINTENANCE AND MINOR REPAIR
lkef;d j[kj[kko rFkk ekewyh ejEer
pg56_96.pmd2/25/2005, 9:59 AM 67

Antidote
fo"k uk'kd %
EXTERNAL: Flush with water.ckgjh ¼okg~;½ %
ikuh ls vPNh rjg ls
/kks ysaA
INTERNAL: Drink large quantities
of water or milk. Follow with milk
of magnesia, beaten egg, or
vegetable oil. Call a physician
immediately.vkarfjd %
cgqr vf/kd ek=kk esa ikuh
vFkok nw/k ih ysaA ckn esa lQsn feV~Vh
;qDr nw/k] QsaVk gqvk vaMk vFkok ouLifr
rsy dk lsou djsaA fpfdRld dks rqjar
cqyk ysaA
EYES: Flush with water for 15
minutes and get prompt medical
attention Batteries produce
explosive gases. Keep sparks,
flame, cigarettes etc., away.
Ventilate when charging or using
in an enclosed space. Always
shield your eyes when working
near batteries. KEEP OUT OF
REACH OF CHILDREN.
vk¡[kas % vk¡[kksa dks
15
feuV rd ikuh ls
vPNh rjg ls /kks,a vkSj tYnh ls MkDVj
dks fn[kk,aA cSV~jh] ls foLQksVd xSsl
fudyrh gS] fpaxkjh vkx dh yiV ¼ykS½
rFkk flxjsV bR;kfn ls bls nwj j[ksaA
can LFkku ij bls pkt+Z djrs le;
vFkok iz;ksx djrs le; gok ds vkus&tkus
ds LFkku dks [kqyk j[ksaA cSV~jh ds ut+nhd
dke djrs le; ges'kk viuh vk¡[kksa dks
gh j[ksaA
ENSURE THAT BATTERY ELECTROLYTE LEVEL IS MAINTAINED BETWEEN
MAX. AND MIN. MARKS. IF REQUIRED, ADD DISTILLED WATER ONLY
6.34
WARNINGBattery electrolyte is poisonous
and dangerous, causing severe
burns, etc. It contains sulfuric acid.
Avoid contact with skin, eyes or
clothing. psrkouhcSV~jh dk ^bysDV ªksykbZV* fo"kSyk vkSj
[krjukd gksrk gS ftlds laidZ esa vkuss
ij rst tyu bR;kfn gksrh gSA blesa
lY¶;wfjd vEy gksrk gSA bls Ropk]
vk¡[kksa rFkk diM+ksa ds lkFk laidZ gksus ls
cpk,aAPERIODIC MAINTENANCE AND MINOR REPAIRlkef;d j[kj[kko rFkk ekewyh ejEer
pg56_96.pmd2/25/2005, 9:59 AM 70

2.
b±/ku dh [kkyh Vadh dks ckgj fudky
ysa] Vadh esa ,d di
SAE 10W30 or
20W40
czkaM dk eksVj vkW;y Mkysaa]
fQj Vadh ds van:uh lrg dh dks¯Vx
djus ds fy, Vadh dks vPNh rjg ls
fgyk,a vkSj Qkyrw rsy dks ckgj fudky
nsaA Vadh dks fQj ls ;FkkLFkku ij
yxk nsaA
3. Remove the spark plug, pour
about one tablespoon of SAE
10W30 or 20W40 motor oil in the
spark plug hole. Reinstall spark
plug. Kick the engine over several
times (with the ignition off) to coat
the cylinder wall with oil.
LikWdZ Iyx dks ckgj fudky ys]
SAE
10W30 or 20W40
czkaM dk ,d cM+k
pEep LikWdZ Iyx ds Nsn esa ¼gksy½
Mkysa vkSj bls fQj ls okil yxk nsaA
batu dks dqN le; rd fdd yxkrs
jgsa ¼bXuh'u dks can j[krs gq,½ ftlls
flyh.Mj dh fnokjksa dh vkW;y&dks¯Vx
gks tk,A
4. Remove the drive chain.
Thoroughly clean the chain
withsolvent and lubricate it.
Reinstall the chain or store it in a
B. STORAGEch- Hk.Mkj.k ¼LVksjst½Long term storage (60 days or more)
of your Motorcycle will require more
preventive procedures to guard
against deterioration. After thoroughly
cleaning the Motorcycle, prepare for
storage as follows:vkidh eksVjlkbfdy dks yEch vof/k rd
¼60
fnu ;k mlls Åij½ ^LVksj* djds
j[kus ij bls u"V gksus ls cpkus ds fy,
lko/kkuho'k dqN izfØ;k,a viukuh iM+rh
gSaA eksVjlkbfdy dks iwjh rjg lQkbZ
djus ds ckn] fuEufyf[kr ckrkssa dk vuqlj.k
djds] bls ^LVksj* djus dh rS;kjh djsa %
1. Drain the fuel tank, fuel lines, and
carburetor float bowl.
b±/ku dh Vadh] b±/ku dh ykbZuksa] vkSj
dkjC;wjsVj ds ¶yksV&ckÅy dks [kkyh
djs ysaA
2. Remove the empty fuel tank, pour
a cup of SAE 10W30 or 20W40
motor oil in the tank, shake the
tank to coat the inner surfaces tank
to coat the inner surfaces
thoroughly and drain off the excess
oil. Reinstall the tank.plastic bag (tied to frame for
safekeeping).
M ªkbo&pSu dks ckgj fudky ysaA
bls iwjh rjg ls nzkod ¼lkWYosaV½ ls
lkQ djsa vkSj bl ij xzhl bR;kfn
yxk nsaA pSu dks fQj ls yxk nsa
vFkok bls ,d IykWfLVd & cSx esa
^LVksj* djds j[k ysaA ¼lqjf{kr j[kus
ds fy, Ýse ds lkFk cka/k nsa½A
5. Lubricate all control cables.
lHkh daVªksy&dscyksa ¼rkjksa½ dh xzh¯lx
dj ysaA
6. Block up the frame to raise both
wheels off the ground.
nksuksa ifgvksa dks t+ehu ls Åij mBkus
ds fy, Ýse dks jksddj j[ksaA
7. Tie a plastic bag over the
exhaust pipe outlet to prevent
moisture from entering.
ueh dks ^,XtkWLV&ikbi* ¼fudkl&uyh½
ds vanj vkus ls cpkus dss fy, ikbi
dks ckgj ls IykWfLVd cSx ls ¼yisV½ nsaA
CLEANING AND STORAGElQkbZ rFkk HkaMkj.k
7.3
pg56_96.pmd2/25/2005, 9:59 AM 86

SPECIFICATIONS
ModelCRUX S
Dimensions:
Overall length2,000 mm
Overall width 735 mm
Overall height1,075 mm
Seal height 780 mm
Wheelbase1,260 mm
Ground clearance160 mm
Minimum turning radius 2,000 mm
Weight : ( With oil & 90% fuel ) 113 kg
Engine :Engine type Air cooled 4-stroke,
SOHC
Cylinder arrangement Forward inclined
single cylinder
Displacement105.6 cm
3
Boer × Stroke49×56 mm
Compression ratio9.0 : 1
Starting systemKick starter
Lubrication systemWet sump
Maximum power7.60BHP(5.59kw) @ 7500 RPM
Maximum torque 0.8 Mkg @ 6000 RPM
EngineOil
Type:
CAUTION :
Be sure to use motor oils that do not contain
antifrication modifiers. Passenger car motor oils
(often labelled Energy conserving) contain anti-
friction additives which will cause clutch/or
starter clutch slippage, resulting in reduced
component life and poor engine performance.
Capacity :
Periodic oil change 0.9 L
Total amount 1.1 L
Air filter:Foam type element
Fuel :
Type Regular gasoline
(petrol)
Fuel tank capacity 11.0 Litres
Reserve amount1.4 Litres
Carburetor:
Type VM17SH
ManufactureMIKUNI
SPECIFICATIONSfo'ks"k fooj.k
8.1
YAMALUBE
4-Stroke motor oil (20W40)
Type SG
pg56_96.pmd2/25/2005, 9:59 AM 88

Wheels:
Type:
FrontSpoke wheel
RearSpoke wheel
Size:Front1.60 × 18
Rear1.60 × 18
Brake:
Front :
Type Drum brake
operationright Hand lever
Rear :
Type Drum brake
OperationRight foot operation
Suspention :
Front Telescopic fork
RearSwing arm
Shock absorber:
Front Coil spring/oil damper
RearCoil spring/oil damperWheels travel:
Front 110 mm
Rear 70 mm
Electrical:
Ignition system:CDI (Digitally
Controlled)
Generator system:
Type Flywheel magneto
Standard output 12V
Battery:
Type Lead acid
Voltage, capacity 12V 2.5AH
Bulb voltage, Wattage × Quantity:
Headlight12V 35W/35W × 1
Tail/Brake light 12V 21W/5W × 1
Front flasher light 12V 10W × 2
Rear flasher light 12V 10W × 2
Meter light 12V 2W × 1
Neutral indicator light 12V 3.4W × 1
High beam indicator light 12V 3.4W × 1
Turn indicator light 12V 3.4W × 1
Fuse:
Main 10A
8.5
SPECIFICATIONSfo'ks"k fooj.k
pg56_96.pmd2/25/2005, 9:59 AM 92