low beam YAMAHA YFZ450 2007 Owners Manual

Parking ...................................................... 6-5
Parking on a slope .................................... 6-6
Accessories and loading ........................... 6-6
RIDING YOUR ATV ...................................... 7-1
GETTING TO KNOW YOUR ATV.............. 7-2
RIDE WITH CARE AND GOOD
JUDGEMENT ...........................................7-2
BE CAREFUL WHERE YOU RIDE ............ 7-8
TURNING YOUR ATV ............................. 7-12
CLIMBING UPHILL .................................. 7-14
RIDING DOWNHILL................................. 7-16
CROSSING A SLOPE.............................. 7-17
CROSSING THROUGH SHALLOW
WATER ..................................................7-18
RIDING OVER ROUGH TERRAIN .......... 7-20
SLIDING AND SKIDDING ........................ 7-20
WHAT TO DO IF... ................................... 7-21
WHAT TO DO... ....................................... 7-21
PERIODIC MAINTENANCE AND MINOR
REPAIR .......................................................... 8-1
Owner’s manual and tool kit ...................... 8-1
Periodic maintenance and lubrication
chart ........................................................ 8-3
Removing and installing the panel ............ 8-8
Checking the spark plug ............................ 8-9
Engine oil and oil filter element ............... 8-13
Coolant .................................................... 8-19Cleaning the air filter element .................. 8-23
Cleaning the spark arrester ..................... 8-26
Adjusting the carburetor ........................... 8-28
Checking the engine idling speed ............ 8-29
Adjusting the throttle cable free play ........ 8-29
Valve clearance ....................................... 8-30
Checking the front and rear brake pads .. 8-30
Checking the brake fluid level .................. 8-31
Changing the brake fluid .......................... 8-34
Checking the front brake lever free play .. 8-34
Checking the brake pedal position ........... 8-35
Adjusting the parking brake free play ...... 8-36
Brake light switches ................................. 8-37
Adjusting the clutch lever free play .......... 8-38
Drive chain slack ...................................... 8-39
Lubricating the drive chain ....................... 8-41
Checking and lubricating the cables ........ 8-42
Checking and lubricating the brake and
clutch levers ........................................... 8-42
Checking and lubricating the brake and
shift pedals ............................................. 8-43
Checking the wheel bearings ................... 8-43
Lubricating the swingarm pivots .............. 8-44
Lubricating the upper and lower arm
pivots ..................................................... 8-44
Battery ..................................................... 8-45
Replacing the fuse ................................... 8-46
Replacing a headlight bulb ...................... 8-47
Adjusting a headlight beam ..................... 8-49

4-3
1
2
34
5
6
7
8
9
10
11

EBU18060
Handlebar switches
EBU18070
Engine stop switch “ENG. STOP”
Set this switch to “RUN” before starting the engine.
The engine stop switch controls the ignition and
stops the engine when it is running. Use this switch
to stop the engine in an emergency situation. The
engine will not start or run when this switch is set
to “OFF”.
EBU18090
Start switch “START”
Push this switch to crank the engine with the start-
er.CAUTION:

ECB00050
See the starting instructions on page 6-1 prior
to starting the engine.
EBU18120
Light switch “LIGHTS”
Set this switch to “LO” to turn on the low beams
and the taillight. Set the switch to “HI” to turn on the
high beams and the taillight. Set the switch to
“OFF” to turn off all the lights.
NOTE:

The headlights and the taillight can be turned on
only when the engine is running.
EBU18280
Throttle lever
Once the engine is running, movement of the throt-
tle lever will increase the engine speed.
Regulate the speed of the ATV by varying the
throttle position. Because the throttle is spring-
loaded, the ATV will decelerate, and the engine will
1. Light switch “LIGHTS”
2. Engine stop switch “ENG. STOP”
3. Start switch “START”
1
2
3

8-49
1
2
3
4
5
6
78
9
10
11
CAUTION:

ECB00650
Do not touch the glass part of the headlight
bulb to keep it free from oil, otherwise the
transparency of the glass, the luminosity of the
bulb, and the bulb life will be adversely affect-
ed. Thoroughly clean off any dirt and finger-
prints on the headlight bulb using a cloth
moistened with alcohol or thinner.
6. Install the headlight bulb holder by pushing it
in and turning it clockwise.
7. Install the headlight bulb holder cover.8. Connect the headlight coupler.
9. Install the headlight unit by installing the bolts.
10. Adjust the headlight beam if necessary.
EBU25550
Adjusting a headlight beam
CAUTION:

ECB00690
It is advisable to have a Yamaha dealer make
this adjustment.
To raise a headlight beam, turn the adjusting
screw in direction (a).
To lower a headlight beam, turn the adjusting
screw in direction (b).
1. Do not touch the glass part of the bulb.
1

1. Headlight beam adjusting screw
1(a)
(b)