air filter YAMAHA YFZ450R 2011 Owners Manual

Accessories and loading ............................ 6-6
RIDING YOUR ATV ...................................... 7-1
GETTING TO KNOW YOUR ATV............... 7-2
RIDE WITH CARE AND GOOD
JUDGMENT .............................................. 7-2
BE CAREFUL WHERE YOU RIDE ............. 7-9
TURNING YOUR ATV .............................. 7-12
CLIMBING UPHILL ................................... 7-13
RIDING DOWNHILL.................................. 7-16
CROSSING A SLOPE............................... 7-18
CROSSING THROUGH SHALLOW
WATER ................................................... 7-19
RIDING OVER ROUGH TERRAIN ........... 7-20
SLIDING AND SKIDDING ......................... 7-21
WHAT TO DO IF... .................................... 7-22
WHAT TO DO... ........................................ 7-22
PERIODIC MAINTENANCE AND
ADJUSTMENT ............................................... 8-1
Owner’s manual and tool kit ....................... 8-2
Periodic maintenance chart for
the emission control system ..................... 8-3
General maintenance and
lubrication chart ........................................ 8-5
Removing and installing the cowling and
panels ....................................................... 8-9Checking the spark plug ...........................8-12
Engine oil and oil filter element .................8-13
Coolant .....................................................8-19
Cleaning the air filter element ...................8-20
Cleaning the spark arrester ......................8-24
Adjusting the throttle lever free play .........8-26
Valve clearance ........................................8-27
Brakes .......................................................8-27
Checking the front and rear brake pads ...8-27
Checking the brake fluid level ...................8-29
Changing the brake fluid ...........................8-30
Checking the front brake lever free play ...8-30
Checking the brake pedal height ..............8-30
Adjusting the parking brake free play .......8-31
Brake light switches ..................................8-32
Adjusting the clutch lever free play ...........8-33
Drive chain slack .......................................8-34
Lubricating the drive chain ........................8-36
Checking and lubricating the cables .........8-37
Checking and lubricating the brake and
clutch levers ............................................8-38
Checking the shift pedal ...........................8-38
Checking and lubricating the brake
pedal .......................................................8-38
Checking the wheel hub bearings .............8-39
Lubricating the swingarm pivots ...............8-39
U18P64E0.book Page 2 Thursday, May 13, 2010 6:00 PM

4-17
4
NOTICEECB00090Never turn an adjusting mechanism beyond
the minimum and maximum settings.TIPAlthough the total number of clicks or turns of a
damping force adjusting mechanism may not ex-
actly match the following specifications due to
small differences in production, the actual number
of clicks or turns always represents the entire ad-
justing range. To obtain a precise adjustment, it
would be advisable to check the number of clicks
or turns of each damping force adjusting mecha-
nism and to modify the specifications as neces-
sary.Spring preload
1. Remove the cowling. (See page 8-9.)
2. Remove the clip from the hose holder, remove
the bolt, and then move the blow-by gas
chamber away from the vehicle.3. Loosen the clamp screw at the air filter case
side.
1. Hose holder
2. Clip
3. Bolt
4. Blow-by gas chamber
23
4
1
U18P64E0.book Page 17 Thursday, May 13, 2010 6:00 PM

4-18
4
4. Remove the air filter case holding plate by re-
moving the bolts and collars.
5. Remove the bolts, and then remove the air fil-
ter case by disconnecting it from the air intake
duct.
1. Clamp screw
1
1. Bolt
2. Collar
3. Air filter case holding plate
1
1
2
3
U18P64E0.book Page 18 Thursday, May 13, 2010 6:00 PM

4-19
4
6. Disconnect the coupler.7. Loosen the clamp screw at the throttle body
side, and then disconnect the air intake duct
from the throttle body.
8. Loosen the locknut.
9. Turn the spring preload adjusting nut in direc-
tion (a) to increase the spring preload and
thereby harden the suspension, and in direc-
tion (b) to decrease the spring preload and
thereby soften the suspension.
1. Air filter case
2. Bolt
1. Coupler
12 2
1
1. Clamp screw
2. Air intake duct
1
2
U18P64E0.book Page 19 Thursday, May 13, 2010 6:00 PM

4-21
411. Connect the air intake duct to the throttle
body, and then tighten the clamp screw at the
throttle body side. NOTICE: Make sure that
the air intake duct is properly connected to
the throttle body, and that the clamp screw
is tightened securely.
[ECB00961]
12. Connect the coupler.
13. Place the air filter case in the original position,
connect the air intake duct to the air filter case,
and then tighten the clamp screw at the air fil-
ter case side. NOTICE: Make sure that the
air intake duct is properly connected to the
air filter case, and that the clamp screw is
tightened securely.
[ECB00971]
14. Install the air filter case bolts, and then tighten
them to the specified torque.15. Install the air filter case holding plate by install-
ing the bolts and collars, and then tighten the
bolts to the specified torque.
16. Install the blow-by gas chamber by installing
the bolt, tighten the bolt to the specified
torque, and then install the clip to the hose
holder.
17. Install the cowling.
Rebound damping force
Turn the rebound damping force adjusting screw in
direction (a) to increase the rebound damping
force and thereby harden the damping, and in di-
rection (b) to decrease the rebound damping force
and thereby soften the damping. Tightening torque:
Locknut:
30 Nm (3.0 m·kgf, 22 ft·lbf)
Tightening torque:
Air filter case bolt:
7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Tightening torque:
Air filter case holding plate bolt:
7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Tightening torque:
Blow-by gas chamber bolt:
7 Nm (0.7 m·kgf, 5.1 ft·lbf)
U18P64E0.book Page 21 Thursday, May 13, 2010 6:00 PM

7-20
7
After riding your ATV in water, be sure to drain the
trapped water by removing the check hose at the
bottom of the air filter case. NOTICE: Undrained
water can cause damage or improper opera-
tion.
[ECB00841]
Wash the ATV in fresh water if it has been operat-
ed in salt water or muddy conditions.RIDING OVER ROUGH TERRAIN
WARNING
EWB01651Riding improperly over obstacles could cause
loss of control or a collision. Before operating
in a new area, check for obstacles. Never at-
tempt to ride over large obstacles, such as
large rocks or fallen trees. When you go over
obstacles, always follow proper procedures as
described in the Owner’s Manual.Riding over rough terrain should be done with cau-
tion. Look out for obstacles which could cause
damage to the ATV or could lead to an upset or ac-1. Air filter case check hose
1
U18P64E0.book Page 20 Thursday, May 13, 2010 6:00 PM

8-5
8
EBU21865General maintenance and lubrication chart TIP
For ATVs not equipped with an odometer or an hour meter, follow the month maintenance intervals.
For ATVs equipped with an odometer or an hour meter, follow the km (mi) or hours maintenance inter-
vals. However, keep in mind that if the ATV isn’t used for a long period of time, the month maintenance
intervals should be followed.
Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools,
data and technical skills.NO. ITEMCHECK OR MAINTENANCE
JOBINITIAL EVERY
Whichev-
er comes
firstmonth136612
km
(mi)320
(200)1300
(800)2500
(1600)2500
(1600)5000
(3200)
hours 20 80 160 160 320
1 Air filter elementClean and replace if necessary.Every 20–40 hours (more often in wet or
dusty areas)
2*ClutchCheck operation and adjust if necessary.√ √√√
3*Front brakeCheck operation and correct if necessary.
Check fluid level and ATV for fluid leakage, and
correct if necessary.√√√√√
Replace brake pads. Whenever worn to the limit
4*Rear brakeCheck operation and correct if necessary.
Check fluid level and ATV for fluid leakage, and
correct if necessary.√√√√√
Replace brake pads. Whenever worn to the limit
U18P64E0.book Page 5 Thursday, May 13, 2010 6:00 PM

8-7
8
14*Chassis fastenersMake sure that all nuts, bolts, and screws are
properly tightened.√√√√√
15*Shock absorber as-
sembliesCheck operation and correct if necessary.
Check for oil leakage and replace if necessary.√√√
16*Rear suspension re-
lay arm and con-
necting arm
pivoting pointsCheck operation and correct if necessary.√√√√
17*Steering shaftLubricate with lithium-soap-based grease.√√√
18*Steering systemCheck operation and repair or replace if damaged.
Check toe-in and adjust if necessary.√√√√√
19 Engine oilChange.
Check ATV for oil leakage, and correct if neces-
sary.√ √√√
20Engine oil filter ele-
mentReplace.√√√
21*Cooling systemCheck coolant level and ATV for coolant leakage,
and correct if necessary.√√√√√
Replace coolant. Every 2 years
22*Moving parts and
cablesLubricate.√√√√ NO. ITEMCHECK OR MAINTENANCE
JOBINITIAL EVERY
Whichev-
er comes
firstmonth136612
km
(mi)320
(200)1300
(800)2500
(1600)2500
(1600)5000
(3200)
hours 20 80 160 160 320U18P64E0.book Page 7 Thursday, May 13, 2010 6:00 PM

8-20
83. If the coolant is at or below the minimum level
mark, remove the coolant reservoir cap, add
coolant or distilled water to the maximum level
mark, and then install the reservoir cap.
NOTICE: If coolant is not available, use
distilled water or soft tap water instead. Do
not use hard water or salt water since they
are harmful to the engine. If water has
been used instead of coolant, replace it
with coolant as soon as possible, other-
wise the cooling system will not be pro-
tected against frost and corrosion. If water
has been added to the coolant, have a
Yamaha dealer check the antifreeze con-
tent of the coolant as soon as possible,
otherwise the effectiveness of the coolant
will be reduced.
[ECB01011]
TIP
The radiator fan is automatically switched on or
off according to the coolant temperature in the
radiator.

If the engine overheats, see page 8-50 for fur-
ther instructions.EBU26806Cleaning the air filter element The air filter element should be cleaned at the in-
tervals specified in the periodic maintenance and
lubrication chart. Clean or, if necessary, replace
the air filter element more frequently if you are
riding in unusually wet or dusty areas.TIPThere is a check hose at the bottom of the air filter
case. If dust or water collects in this hose, empty
the hose and clean the air filter element and air fil-
ter case.
Coolant reservoir capacity (up to the maxi-
mum level mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
U18P64E0.book Page 20 Thursday, May 13, 2010 6:00 PM

8-21
8 1. Place the ATV on a level surface.
2. Remove the seat. (See page 4-10.)
3. Remove the air filter case cover by unhooking
the holders.4. Fully loosen the wing bolt.
5. Remove the air filter element together with the
wing bolt and washer.
1. Air filter case check hose
1
1. Air filter case cover
2. Air filter case cover holder
1
2
U18P64E0.book Page 21 Thursday, May 13, 2010 6:00 PM