brake YAMAHA YS125 2017 User Guide

Periodic maintenance an d a djustment
6-5
6
10 *Tires • Check tread depth and for dam-
age.
• Replace if necessary.
• Check air pressure.
• Correct if necessary. √√√√√
11 *Wheel bearin gs • Check bearing for looseness or
damage. √√√√
12 *Swin
garm pivot
b ushes • Check bush assemblies for
looseness. √√√√
• Lubricate with lithium-soap- based grease. √√
13 Drive chain • Check chain slack, alignment and
condition.
• Adjust and lubricate chain with a special O-ring chain lubricant
thoroughly. Every 1000 km (600 mi) and after washing the motorcycle, riding in the rain or
riding in wet areas
14 *Steerin g b earin gs • Check bearing assemblies for
looseness. √√√√
• Moderately repack with lithium- soap-based grease. √
15 *Chassis fasteners • Make sure that all nuts, bolts and
screws are properly tightened. √√√√√
16 Brake lever pivot
shaft
• Lubricate with silicone grease.
√√√√√
17 Brake ped
al pivot
shaft • Lubricate with lithium-soap-
based grease. √√√√√
18 Clutch lever pivot
shaft • Lubricate with lithium-soap-
based grease. √√√√√
NO. ITEM CHECK OR MAINTENANCE JOB
ODOMETER READING
ANNUAL
CHECK
1000 km
(600 mi) 6000 km
(3500 mi) 12000 km
(7000 mi) 18000 km
(10500 mi) 24000 km
(14000 mi)UBT4E0E0.book Page 5 Thursday, November 17, 2016 10:55 AM

Periodic maintenance an d a djustment
6-6
6
19 Shift pe
dal pivot
shaft • Lubricate with lithium-soap-
based grease. √√√√√
20 *Unifie
d b rake sys-
tem • Check cable free play, and adjust
if necessary. √√√√√√
• Lubricate link pivot of brake pedal with lithium-soap-based grease. √√√√√
21 Si
destan d, center-
stan d • Check operation.
• Lubricate with lithium-soap-
based grease. √√√√√
22 *Sidestan d switch • Check operation and replace if
necessary. √√√√√√
23 *Front fork • Check operation and for oil leak-
age.
• Replace if necessary. √√√√
24 *Shock a
bsor ber as-
sem blies • Check operation and for oil leak-
age.
• Replace if necessary. √√√√
25 En gine oil • Change (warm engine before
draining).
• Check oil level and vehicle for oil leakage. √√√√√√
26 En
gine oil filter ele-
ment •Replace.
√√√
27 *Front an
d rear
b rake switches • Check operation.
√√√√√√
28 *Movin
g parts an d
ca bles • Lubricate.
√√√√√
NO. ITEM CHECK OR MAINTENANCE JOB
OD OMETER READING
ANNUAL
CHECK
1000 km
(600 mi) 6000 km
(3500 mi) 12000 km
(7000 mi) 18000 km
(10500 mi) 24000 km
(14000 mi)
UBT4E0E0.book Page 6 Thursday, November 17, 2016 10:55 AM

Periodic maintenance an d a djustment
6-7
6
EAU72690
TIP The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
 Hydraulic brake service
• Regularly check and, if necessary, correct the brake fluid level.
• Every two years replace the internal components of the brake master cylinder and caliper, and change the brake fluid.
• Replace the brake hoses every four years and if cracked or damaged.29 *Throttle
grip hous-
in g an d cab le • Check operation and free play.
• Adjust the throttle cable free play
if necessary.
• Lubricate the throttle grip housing and cable. √√√√√
30 *Li
ghts, si gnals an d
switches • Check operation.
• Adjust headlight beam.
√√√√√√
NO. ITEM CHECK OR MAINTENANCE JOB
ODOMETER READING
ANNUAL
CHECK
1000 km
(600 mi) 6000 km
(3500 mi) 12000 km
(7000 mi) 18000 km
(10500 mi) 24000 km
(14000 mi)UBT4E0E0.book Page 7 Thursday, November 17, 2016 10:55 AM

Periodic maintenance an d a djustment
6-20
6
6. To increase the clutch lever free
play, turn the clutch lever free play
adjusting nut in direction (a). To
decrease the clutch lever free
play, turn the adjusting nut in di-
rection (b).
7. Tighten the locknut at the clutch cable, and then slide the rubber
cover to its original position.
8. Tighten the locknut at the clutch lever, and then slide the rubber
cover to its original position.
EAU37914
Checkin g the brake lever free
playThere should be no free play at the
brake lever end. If there is free play,
have a Yamaha dealer inspect the
brake system.
WARNING
EWA14212
A soft or spon gy feelin g in the brake
lever can in dicate the presence of
air in the hy draulic system. If there is
air in the hy draulic system, have a
Yamaha dealer blee d the system be-
fore operatin g the vehicle. Air in the
hy draulic system will diminish the b
rakin g performance, which may re-
sult in loss of control an d an acci-
d ent.
1. Rubber cover
2. Clutch lever free play adjusting nut
3. Locknut
3
21(b)
(a)
1. No brake lever free play
1
UBT4E0E0.book Page 20 Thursday, November 17, 2016 10:55 AM

Periodic maintenance an d a djustment
6-21
6
EAU39815
A djustin g the brake pe dal free
playMeasure the brake pedal free play at
the brake pedal end as shown.
Periodically check the brake pedal free
play and, if necessary, adjust it as fol-
lows.
To increase the brake pedal free play,
turn the brake pedal free play adjusting
nut at the brake rod in direction (a). To
decrease the brake pedal free play,
turn the adjusting nut in direction (b).
WARNING
EWA10681
 After a djustin g the drive chain
slack or removin g an d installin g
the rear wheel, always check
the brake pe dal free play.
 If proper a djustment cannot b e
o btaine d as descri bed , have a
Yamaha dealer make this ad -
justment.
 After a djustin g the brake ped al
free play, check the operation of
the brake li ght.
EAU22274
Brake li ght switchesThe brake light, which is activated by
the brake pedal and brake lever,
should come on just before braking
takes effect. If necessary, adjust the
rear brake light switch as follows, but
the front brake light switch should be
adjusted by a Yamaha dealer.
Turn the rear brake light switch adjust-
ing nut while holding the rear brake
light switch in place. To make the
brake light come on earlier, turn the ad-
justing nut in direction (a). To make the
brake light come on later, turn the ad-
justing nut in direction (b).
1. Brake pedal free playBrake pe dal free play:
10.0–20.0 mm (0.39–0.79 in)
1
1. Brake pedal free play adjusting nut
1
(a)
(b)
1. Rear brake light switch
2. Rear brake light switch adjusting nut
1 2
(a)
(b)
UBT4E0E0.book Page 21 Thursday, November 17, 2016 10:55 AM

Periodic maintenance an d a djustment
6-22
6
EAU22382
Checkin g the front b rake pads
an d rear b rake shoes The front brake pads and the rear
brake shoes must be checked for wear
at the intervals specified in the periodic
maintenance and lubrication chart.
EAU22432
Front brake pad s
Each front brake pad is provided with
wear indicator grooves, which allow
you to check the brake pad wear with-
out having to disassemble the brake.
To check the brake pad wear, check
the wear indicator grooves. If a brake
pad has worn to the point that the wear indicator grooves have almost disap-
peared, have a Yamaha dealer replace
the brake pads as a set.
EAU43171
Rear
brake shoes
The rear brake is provided with a wear
indicator, which allows you to check
the brake shoe wear without having to
disassemble the brake. To check the
brake shoe wear, check the position of
the wear indicator while applying the
brake. If a brake shoe has worn to the
point that the wear indicator reaches
the wear limit mark, have a Yamaha
dealer replace the brake shoes as a
set.
EAU32346
Checkin g the brake flui d levelBefore riding, check that the brake fluid
is above the minimum level mark.
Check the brake fluid level with the top
of the reservoir level. Replenish the
brake fluid if necessary.
WARNING
EWA15991
Improper maintenance can result in
loss of b raking a bility. O bserve
these precautions:
1. Brake pad wear indicator groove
1
1
1. Brake shoe wear limit mark
2. Brake shoe wear indicator
1
2
1. Minimum level mark
Specified b rake flui d:
DOT 41
UBT4E0E0.book Page 22 Thursday, November 17, 2016 10:55 AM

Periodic maintenance an d a djustment
6-23
6 
Insufficient brake flui d may al-
low air to enter the b rake sys-
tem, re ducin g brakin g
performance.
 Clean the filler cap before re-
moving . Use only DOT 4 b rake
flui d from a seale d container.
 Use only the specified b rake flu-
i d ; otherwise, the ru bber seals
may deteriorate, causin g leak-
a g e.
 Refill with the same type of
brake flui d. A ddin g a brake flui d
other than DOT 4 may result in a
harmful chemical reaction.
 Be careful that water does not
enter the brake flui d reservoir
when refillin g. Water will si gnifi-
cantly lower the boilin g point of
the flui d an d may result in vapor
lock.
NOTICE
ECA17641
Brake flui d may damag e painted
surfaces or plastic parts. Always
clean up spille d flui d imme diately.
As the brake pads wear, it is normal for
the brake fluid level to gradually go
down. A low brake fluid level may indi-
cate worn brake pads and/or brake
system leakage; therefore, be sure to
check the brake pads for wear and the
brake system for leakage. If the brake
fluid level goes down suddenly, have a
Yamaha dealer check the cause before further riding.
EAU22724
Chan gin g the brake flui d Have a Yamaha dealer change the
brake fluid at the intervals specified in
the periodic maintenance and lubrica-
tion chart. In addition, have the oil seals
of the brake master cylinder and cali-
per as well as the brake hose replaced
at the intervals listed below or whenev-
er they are damaged or leaking.
 Oil seals: Replace every two
years.
 Brake hose: Replace every four
years.
UBT4E0E0.book Page 23 Thursday, November 17, 2016 10:55 AM

Periodic maintenance an d a djustment
6-24
6
EAU22762
Drive chain slackThe drive chain slack should be
checked before each ride and adjusted
if necessary.
EAU22799
To check the drive chain slack
1. Place the motorcycle on the cen- terstand.
2. Shift the transmission into the neutral position.
3. Measure the drive chain slack as shown. 4. If the drive chain slack is incorrect,
adjust it as follows. NOTICE: Im-
proper drive chain slack will
overloa d the en gine as well as
other vital parts of the motorcy-
cle an d can lead to chain slip-
pa ge or b reakag e. To prevent
this from occurrin g, keep the
d rive chain slack within the
specifie d limits.
[ECA10572]
EAU78831
To adjust the drive chain slack
Consult a Yamaha dealer before ad-
justing the drive chain slack. 1. Take the motorcycle off the cen- terstand, and then put the side-
stand down.
2. Loosen the brake pedal free play adjusting nut, brake torque rod
nut, and axle nut.
3. Loosen the drive chain puller lock-nut at each end of the swingarm.
1. Drive chain slackDrive chain slack:40.0–50.0 mm (1.57–1.97 in)
1
1. Brake pedal free play adjusting nut
2. Brake torque rod nut
1. Axle nut
2. Drive chain slack adjusting nut
3. Drive chain puller locknut
4. Drive chain puller
1
2
4 31
2
(a)(b)
UBT4E0E0.book Page 24 Thursday, November 17, 2016 10:55 AM

Periodic maintenance an d a djustment
6-25
6 4. Place the motorcycle on the cen-
terstand.
5. To tighten the drive chain, turn the drive chain slack adjusting nut at
each end of the swingarm in direc-
tion (a). To loosen the drive chain,
turn the adjusting nut at each end
of the swingarm in direction (b),
and then push the rear wheel for-
ward.
TIPUsing the alignment marks on each
drive chain puller, make sure that both
drive chain pullers are in the same po-
sition for proper wheel alignment.
6. Take the motorcycle off the cen-terstand, and then put the side-
stand down.
7. Tighten both locknuts, and then tighten the axle nut and brake
torque rod nut to their specified
torques.
8. Adjust the brake pedal free play. (See page 6-21.)
WARNING
EWA10661
After a djustin g the brake pe dal free
play, check the operation of the
b rake li ght.9. Make sure that the drive chain
pullers are in the same position,
the drive chain slack is correct,
and the drive chain moves
smoothly.
EAU23018
Cleanin g an d lu bricatin g the
d rive chainThe drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly wear
out, especially when riding in dusty or
wet areas. Service the drive chain as
follows.NOTICE
ECA10584
The drive chain must be lu bricated
after washin g the motorcycle, ri din g
in the rain or ri din g in wet areas.1. Remove all dirt and mud from the
drive chain with a brush or cloth.TIPFor a thorough cleaning, have a
Yamaha dealer remove the drive chain and soak it in solvent.2. Spray Yamaha chain lubricant or other suitable chain lubricant on
the entire chain, making sure that
all side plates and rollers have
been sufficiently oiled.
1. Washer
2. Alignment marks
1
2
Tightenin g torques:
Locknut: 7 N·m (0.7 kgf·m, 5.1 lb·ft)
Axle nut:
90 N·m (9.0 kgf·m, 65 lb·ft)
Brake torque rod nut: 18 N·m (1.8 kgf·m, 13 lb·ft)
UBT4E0E0.book Page 25 Thursday, November 17, 2016 10:55 AM

Periodic maintenance an d a djustment
6-26
6
EAU23098
Checkin g an d lu bricatin g the
ca blesThe operation of all control cables and
the condition of the cables should be
checked before each ride, and the ca-
bles and cable ends should be lubri-
cated if necessary. If a cable is
damaged or does not move smoothly,
have a Yamaha dealer check or re-
place it. WARNING! Dama ge to the
outer housin g of cab les may result
in internal rustin g an d cause inter-
ference with ca ble movement. Re-
place damag ed cab les as soon as
possi ble to prevent unsafe con di-
tions.
[EWA10712] EAU49921
Checkin
g an d lu bricatin g the
throttle grip an d ca bleThe operation of the throttle grip
should be checked before each ride. In
addition, the cable should be lubricat-
ed by a Yamaha dealer at the intervals
specified in the periodic maintenance
chart.
EAU44276
Checkin g an d lu bricatin g the
b rake an d shift pe dalsThe operation of the brake and shift
pedals should be checked before each
ride, and the pedal pivots should be lu-
bricated if necessary.
Brake pe dal
Shift pe dal
Recommen ded lu bricant:
Yamaha cable lubricant or other
suitable cable lubricant
UBT4E0E0.book Page 26 Thursday, November 17, 2016 10:55 AM