odometer YAMAHA YXZ1000R 2016 Owners Manual

4-6
4
EBU31360Helmet indicator light “ ”
The indicator light comes on and stays on
while the key is turned to “ ” (on) to remind
the occupants to always wear a helmet. If the
indicator light does not come on when the key
is turned to “ ” (on), have a Yamaha dealer
check the electrical circuit.EBU31370Seat belt indicator light “ ”
The indicator light comes on when the key is
turned to “ ” (on) to remind the occupants
to fasten their seat belt. The indicator light
stays on until the driver seat belt is properly
latched. If the indicator light does not come
on when the key is turned to “ ” (on), or if
the indicator light remains on after the driver
seat belt is properly latched, have a Yamaha
dealer check the electrical circuit.
EBU34953Multi-function meter unitThe multi-function meter unit is equipped with
the following:
speedometer
 tachometer1. Tachometer
2. Transmission gear display
3. Shift timing indicator light
4. Speedometer
5. “SELECT” button
6. “MODE” button
7. “RESET” button
8. Clock/Hour meter/Voltage display
9. Fuel meter
10.Odometer/Tripmeter A/Tripmeter B
123456
10 9 8 7
U2HC7LE0.book Page 6 Wednesday, October 7, 2015 12:09 PM

4-7
4
odometer
 two tripmeters
 clock
 hour meter
 voltage display
 fuel meter
 transmission gear display
 shift timing indicator control mode
 self-diagnosis deviceTIPTo switch the display between “MPH” and
“km/h”, turn the key to “ ” (off), then push
and hold the “SELECT” button while turning
the key to “ ” (on).
Speedometer
The speedometer shows the vehicle’s travel-
ing speed.1. Speedometer
1
U2HC7LE0.book Page 7 Wednesday, October 7, 2015 12:09 PM

4-8
4
Tachometer
The tachometer shows the engine speed in
crankshaft revolutions per minute (r/min).
When the vehicle is first powered on, the ta-
chometer needle will sweep once across the
r/min range and then return to zero r/min in
order to test the electrical circuit.NOTICEECB02920Do not operate the engine in the tachome-
ter red zone.Red zone: 10500 r/min and above
Odometer and tripmeter modes
The odometer shows the total distance trav-
eled by the vehicle.
The tripmeters show the distance traveled
since they were last reset.TIP
The odometer will lock at 99999.
1. Tachometer
2. Tachometer red zone
1
2
1. Odometer/Tripmeter A/Tripmeter B
2. “SELECT” button
3. “RESET” button
23
1
U2HC7LE0.book Page 8 Wednesday, October 7, 2015 12:09 PM

4-9
4
The tripmeters will reset and continue
counting after 9999.9 is reached. Pushing the “SELECT” button switches the
display between the odometer mode “ODO”
and the tripmeter modes “TRIP A” and “TRIP
B” in the following order:
ODO → TRIP A → TRIP B → ODO
To reset a tripmeter, select it by pushing the
“SELECT” button, and then push the “RE-
SET” button for three seconds. The tripme-
ters can be used to estimate the distance that
can be traveled with a full tank of fuel. This in-
formation enables you to plan future fuel
stops. Clock, hour meter and voltage display
modes
The clock displays time in 12-hour format.
The hour meter shows the total time the en-
gine has been running.
The voltage display shows the battery volt-
age.
1. Clock/Hour meter/Voltage display
2. “SELECT” button
3. “RESET” button
4. “MODE” button
23
4
1
U2HC7LE0.book Page 9 Wednesday, October 7, 2015 12:09 PM

8-4
8
EBU35770Periodic maintenance chart for the emission control systemFor vehicles equipped with an odometer or an ho ur meter, follow the km (mi) or hours mainte-
nance intervals. However, keep in mind that if the vehicle isn’t used for a long period of time,
the month maintenance intervals should still be followed.
 Items marked with an asterisk should be perfor med by a Yamaha dealer as they require special
tools, data and technical skills.NO. ITEM ROUTINE INITIAL
EVERY
Whichev- er comes first month136612
km
(mi) 320
(200) 1300
(800) 2500
(1600) 2500
(1600) 5000
(3200)
hours 20 80 160 160 320
1 *Fuel line • Check fuel hose for cracks or damage.
• Replace if necessary. √√√
2 *Va l v e s • Check valve clearance.
• Adjust if necessary. √ √√√
3 *Spark plugs • Check condition.
• Adjust gap and clean.
• Replace if necessary. √√√√√
4 *Breather system • Check breather hose for cracks or damage.
• Replace if necessary. √√√
5 *Fuel injection • Adjust synchronization. √√√√√
U2HC7LE0.book Page 4 Wednesday, October 7, 2015 12:09 PM