engine oil YAMAHA YXZ1000R 2017 User Guide

8-18
8
9. Place an oil pan under the engine to col-lect the used engine oil.
10. Remove the engine oil drain bolt and its gasket to drain the oil from the engine.
TIPA “ ” mark is stamped on the crankcase
near the engine oil drain bolt for easy identifi-
cation. 11. Install the engine oil drain bolt, engine oil
tank drain bolt and their new gaskets,
and then tighten the bolts to the specified
torques.
1. Engine oil tank drain bolt
2. Gasket
2
1
1. Engine oil drain bolt
2. Gasket
3. “ ” mark
1 2
3
UB577AE0.book Page 18 Wednesday, June 8, 2016 9:35 AM

8-19
8
12. Add 2.00 L (2.11 US qt, 1.76 Imp.qt) ofthe recommended engine oil to the oil
tank, and then install and tighten the en-
gine oil tank filler cap and the cylinder
head cap.
13. Start the engine, warm it up for several minutes, and then turn it off.
14. Remove the engine oil tank filler cap, and then add sufficient oil of the recommend-
ed type to raise it to the maximum level
mark on the dipstick.
TIPBe sure to wipe off spilled oil on any parts af-
ter the engine and exhaust system have
cooled down. NOTICEECB03020Do not use oils with a diesel specifica-
tion of “CD” or oils of a higher quality
than specified. In addition, do not use
oils labeled “ENERGY CONSERVING II”
or higher.
 Make sure that no foreign material en-
ters the oil tank.
Tightening torques:
Engine oil drain bolt:10 N·m (1.0 kgf·m, 7.2 lb·ft)
Engine oil tank drain bolt: 16 N·m (1.6 kgf·m, 12 lb·ft)
Recommended engine oil: See page 10-1.
Oil quantity: Oil change only:2.50 L (2.64 US qt, 2.20 Imp.qt)
Oil change and filter replacement: 2.70 L (2.85 US qt, 2.38 Imp.qt)
UB577AE0.book Page 19 Wednesday, June 8, 2016 9:35 AM

8-20
8
15. Install and tighten the engine oil tank fillercap.
16. Start the engine, and then let it idle for several minutes while checking it for oil
leakage. If oil is leaking, immediately turn
the engine off and check for the cause.
17. Turn the engine off, wait at least ten mi- nutes, and then check the oil level and
correct it if necessary.
18. Install the engine oil tank cover by install- ing the bolts.
19. Install the panel.
To change the engine oil and oil filter 1. Park the vehicle on a level surface.
2. Loosen the left and right side panels by removing the bolt as shown. 3. Remove the rear bottom panel by remov-
ing the bolts.
1. Left side panel
2. Right side panel
3. Bolt
3
1
3
2
UB577AE0.book Page 20 Wednesday, June 8, 2016 9:35 AM

8-21
8
4. Remove the bolts, and then slide the cen-ter bottom panel rearward to remove it. 5. Drain the engine oil from the both the oil
tank and the engine.
TIPRefer to steps 2–10 of the “To change the en-
gine oil” section for th e oil draining procedure. 6. Remove the oil filter cartridge with an oil
filter wrench. Make sure that the O-ring is
removed together with the oil filter car-
tridge. If the O-ring remains attached to
the crankcase, oil leakage may occur.
1. Rear bottom panel
2. Bolt
2
1
2
2
1. Center bottom panel
2. Bolt
2
2
2
2
2
1
UB577AE0.book Page 21 Wednesday, June 8, 2016 9:35 AM

8-22
8
TIPAn oil filter wrench is available from a Yamaha
dealer. 7. Apply a light coat of clean engine oil to
the O-ring of the new oil filter cartridge.TIPMake sure that the O-ring is properly seated.
8. Install the new oil filter cartridge with anoil filter wrench, and then tighten it to the
specified torque with a torque wrench.
1. Oil filter cartridge
2. Oil filter wrench
2
1
1. O-ringTightening torque:Oil filter cartridge:17 N·m (1.7 kgf·m, 12 lb·ft)
1
UB577AE0.book Page 22 Wednesday, June 8, 2016 9:35 AM

8-23
8
9. Install the drain bolts, and then add thespecified amount of the recommended
engine oil. Check the engine oil level and
the vehicle for oil leakage. Install the en-
gine oil tank cover and panel C.TIPRefer to steps 11–19 of the “To change the
engine oil” section for the oil filling procedure.
10. Slide the front portion of the center bot- tom panel into place as shown, and then
hook the left and right sides of the center
bottom panel into place.
1. Torque wrench
1
1. Center bottom panel
1
UB577AE0.book Page 23 Wednesday, June 8, 2016 9:35 AM

8-29
8
8. Start the engine and drive the vehicle fora few minutes to circulate the transmis-
sion oil.
9. Park the vehicle on a level surface, stop the engine, and then check the transmis-
sion case for oil leakage.TIPIf oil is leaking confirm that the transmission
oil filler cap is properly installed and then have
a Yamaha dealer check the transmission. 10. Check the transmission oil level and cor- rect if necessary.
11. Install the panel.EBU36050Final gear oilCheck the oil level and change the final gear
oil at the intervals specified in the general
maintenance and lubrication chart.
Checking the final gear oil level 1. Park the vehicle on a level surface. 2. Remove the final gear oil filler bolt and its
gasket, and then check the oil level in the
final gear case. The oil level should be at
the brim of the filler hole.
3. If the oil is below the brim of the filler hole, add sufficient oil of the recommended
type to raise it to the correct level.
NOTICE: Be sure no foreign material
enters the final gear case.
[ECB00422]
1. Final gear oil
2. Gasket
3. Final gear oil filler bolt
4. Correct oil level
24
3
1
UB577AE0.book Page 29 Wednesday, June 8, 2016 9:35 AM

9-2
9
7. Automotive-type wax may be applied toall painted and chrome-plated surfaces.
Avoid combination cleaner-waxes. Many
contain abrasives which may scratch the
paint or protective finish. When finished,
start the engine and let it idle for several
minutes.EBU32741StorageLong term storage (60 days or more) of your
vehicle will require some preventive proce-
dures to guard against deterioration. Make
any necessary repairs before storing the vehi-
cle.
After thoroughly cleaning the vehicle, prepare
for storage as follows:
1. Fill the fuel tank with fresh fuel and add the specified amount of Fuel Med Rx or
another high-quality fuel stabilizer prod-
uct. Follow the instructions on the prod- uct label. Operate the vehicle for at least
5 minutes to distribute treated fuel
through the fuel system.
2. Remove the spark plugs and pour one ta- blespoon of fresh engine oil into each cyl-
inder and then re-install the spark plugs.
Remove the spark plug wires and ground
them. Operate the electric starter to turn
the engine over several times and coat
the cylinder walls with oil.
3. Lubricate all control cables.
4. Put the frame on stands or blocks to raise all wheels off the ground.
5. Tie a plastic bag over the exhaust pipe outlet to prevent moisture from entering.
Specified amount:1 oz of stabilizer to each gallon of fuel (or
7.5 ml of stabilizer to each liter of fuel)
UB577AE0.book Page 2 Wednesday, June 8, 2016 9:35 AM

10-1
10
EBU32750
SPECIFICATIONS
Dimensions:Overall length:3121 mm (122.9 in)
Overall width: 1626 mm (64.0 in)
Overall height:
1834 mm (72.2 in)
Wheelbase: 2300 mm (90.6 in)
Ground clearance: 330 mm (13.0 in)
Minimum turning radius:
6000 mm (236 in)Weight:Curb weight:686.0 kg (1512 lb) (YXZ10YEXH)
705.0 kg (1554 lb) (YXZ10YESH)Noise and vibration level:Noise level (77/311/EEC):
85.8 dB(A) at 4125 r/min (YXZ10YESH_EUR/FRA/GBR,
YXZ10YEXH)
Uncertainty of measurement:
3.0 dB(A) (YXZ10YESH_EUR/FRA/GBR, YXZ10YEXH)
A-weighted sound power level: 100.0 dB(A) at 4125 r/min (YXZ10YESH_EUR/FRA/GBR,
YXZ10YEXH)
Uncertainty of measurement: 3.0 dB(A) (YXZ10YESH_EUR/FRA/GBR, YXZ10YEXH) Vibration on seat (EN1032, ISO5008):
Will not exceed 0.5 m/s² (YXZ10YESH_EUR/FRA/GBR,
YXZ10YEXH)
Uncertainty of measurement:
0.0 m/s² (YXZ10YESH_EUR/FRA/GBR, YXZ10YEXH)
Vibration on handle (EN1032, ISO5008): Will not exceed 2.5 m/s² (YXZ10YESH_EUR/FRA/GBR,
YXZ10YEXH)
Uncertainty of measurement: 0.2 m/s² (YXZ10YESH_EUR/FRA/GBR, YXZ10YEXH)
Engine:Engine type:
Liquid cooled 4-stroke, DOHC
Cylinder arrangement: Inline 3-cylinder
Displacement: 998 cm³
Bore × stroke:
80.0 × 66.2 mm (3.15 × 2.61 in)
Compression ratio: 11.3 : 1
Starting system: Electric starter
Lubrication system:
Dry sumpEngine oil:Recommended brand:YAMALUBE
UB577AE0.book Page 1 Wednesday, June 8, 2016 9:35 AM

10-2
10
Type:SAE 5W-30, 10W-30, 10W-40, 15W-40, 20W-40 or 20W-
50
Recommended engine oil grade: API service SG type or higher, JASO standard MA
Engine oil quantity: Without oil filter cartridge replacement: 2.50 L (2.64 US qt, 2.20 Imp.qt)
With oil filter cartridge replacement: 2.70 L (2.85 US qt, 2.38 Imp.qt)Transmission oil:Recommended brand:YAMALUBE
Type: SAE 5W-30, 10W-30, 10W-40, 15W-40, 20W-40 or 20W-
50
Recommended engine oil grade: API service SG type or higher, JASO standard MA Quantity:
1.50 L (1.59 US qt, 1.32 Imp.qt)
Final gear oil:Type:
SAE 80 API GL-4 Hypoid gear oil
Quantity: 0.47 L (0.50 US qt, 0.41 Imp.qt)Differential gear oil:Type:
SAE 80 API GL-4 Hypoid gear oil
Quantity: 0.18 L (0.19 US qt, 0.16 Imp.qt)Coolant quantity:Coolant reservoir (up to the maximum level mark):
0.31 L (0.33 US qt, 0.28 Imp.qt)
Radiator (including all routes): 3.75 L (3.96 US qt, 3.30 Imp.qt)Air filter:Air filter element:
Wet element
Secondary air filter element: Oil-coated paper elementFuel:Recommended fuel:
Regular unleaded gasoline only
Fuel tank capacity: 34.0 L (8.98 US gal, 7.48 Imp.gal)Fuel injection:Throttle body:
ID mark: 2HC1 00
0 10 30 50 70 90 110 130 F
–20 –10 0 10 20 30 40 50 CSAE 5W-30
SAE 10W-30
SAE 10W-40
SAE 15W-40
SAE 20W-40SAE 20W-50
UB577AE0.book Page 2 Wednesday, June 8, 2016 9:35 AM