light YAMAHA YXZ1000R 2021 User Guide

5-6
5
started, the EPS system may not be working
correctly. When this occurs, have a Yamaha
dealer check the EPS system.
The electrical circuit of the warning light can
be checked by turning the key to “ ” (on). If
the warning light does not come on, have a
Yamaha dealer check the electrical circuit.TIPIf the steering load is too heavy (e.g., exces-
sive steering use at slow speed or when op-
erating in deep mud, sand, or snow), the
power assist is reduced to protect the EPS
motor from overheating. EBU39940Helmet reminder light “ ”
The reminder light comes on and stays on
while the key is turned to “ ” (on) to remind
the occupants to always wear a helmet. If the
reminder light does not come on when the
key is turned to “ ” (on), have a Yamaha
dealer check the electrical circuit.
EBU31371Seat belt reminder light “ ”
The reminder light comes on when the key is
turned to “ ” (on) to remind the occupants
to fasten their seat belt. The reminder light
stays on until the driver seat belt is properly
latched. If the reminder light does not come
on when the key is turned to “ ” (on), or if
the reminder light remains on after the driver
seat belt is properly latched, have a Yamaha
dealer check the electrical circuit.
UB5J7CE0.book Page 6 Thursday, November 26, 2020 1:37 PM

5-7
5
EBU3495DMulti-function meter unitThe multi-function meter unit is equipped with
the following:
speedometer 
tachometer
 odometer
 two tripmeters
 clock
 hour meter
 voltage display
 coolant temperature display
 fuel gauge
 transmission gear display
 shift light control mode
 error code display1. Tachometer
2. Transmission gear display
3. Shift light
4. Speedometer
5. “SELECT” button
6. “MODE” button
7. “RESET” button
8. Clock/Hour meter/Voltage display/Coolant temperature
display
9. Fuel gauge
10.Odometer/Tripmeter A/Tripmeter B
123456
10 9 8 7
UB5J7CE0.book Page 7 Thursday, November 26, 2020 1:37 PM

5-13
5
TIPThis fuel gauge is equipped with a self-diag-
nostic system. If a problem is detected in an
electrical circuit, all the display segments will
flash repeatedly. If this occurs, have a
Yamaha dealer check the electrical circuit. Transmission gear display
This display shows the selected gear. The
neutral position is indicated by “N” and by the
neutral indicator light “N”. Shift light control mode
The shift light has three settings which can be
adjusted.

Flashing pattern: this function allows you to
choose whether or not the light will come
on and whether it should flash or stay on
when activated.
 Activation point: this function allows you to
select the engine speed at which the light is
activated.1. Transmission gear display
2. Neutral indicator light “N”
1
2
1. Shift light
2. çRESETé button
3. çMODEé button
1
23
UB5J7CE0.book Page 13 Thursday, November 26, 2020 1:37 PM

5-14
5
Deactivation point: this function allows you
to select the engine speed at which the light
is deactivated.
To enter shift light control mode1. Turn the key to “ ” (off).
2. Push and hold the “MODE” button.
3. Turn the key to “ ” (on), and then re- lease the “MODE” button after five sec-
onds. After all segments of the display
disappear and the shift light comes on,
the shift light can be adjusted as follows.
To set the flashing pattern1. Push the “RESET” button to select one of the following flashing pattern settings:
On: the shift light stays on when acti-
vated. (The shift light will confirm this
setting by staying on.)
 Flash: the shift light flashes when acti-
vated. (The shift light will confirm this
setting by flashing four times per se-
cond.) 
Off: the shift light is deactivated; in oth-
er words, it does not come on or flash.
(The shift light will confirm this setting
by flashing once every two seconds.)
2. Push the “MODE” button to confirm the
selected flashing pattern. The control
mode then changes to the activation
point setting function. The shift light re-
mains on and the tachometer shows the
current setting r/min for the activation
point.
To set the activation point
TIP The shift light activation point can be set
between 7000 r/min and 12000 r/min. The
activation point can be set in increments of
500 r/min.
 The tachometer needle will start over at
7000 r/min after 12000 r/min.
UB5J7CE0.book Page 14 Thursday, November 26, 2020 1:37 PM

5-15
5
1. Push the “RESET” button to select thedesired engine speed for activating the
shift light.
2. Push the “MODE” button to confirm the selected engine speed. The shift light
flashes and the tachometer shows the
current setting r/min for the deactivation
point.
To set the deactivation pointTIP Be sure to set the deactivation point to a
higher engine speed than for the activation
point, otherwise the shift light will not come
on.
 The shift light deactivation point can be set
between 7000 r/min and 12000 r/min. The
deactivation point can be set in increments
of 500 r/min.
 The tachometer needle will start over at
7000 r/min after 12000 r/min.
1. Push the “RESET” button to select the
desired engine speed for deactivating the
shift light.
2. Push the “MODE” button to confirm the selected engine speed. The display exits
the shift light control mode and returns to
the standard multi-function display mo-
de.
Error code display
This model is equipped with a self-diagnostic
device for various electrical circuits.1. Error code display
2. Engine trouble warning light “ ”
12
UB5J7CE0.book Page 15 Thursday, November 26, 2020 1:37 PM

5-16
5
If a problem is detected in any of those cir-
cuits, the engine trouble warning light will
come on or flash, and the display will indicate
an error code.
If the display indicates an error code, note the
code number and have a Yamaha dealer
check the vehicle.NOTICEECB00812If the multi-function display indicates an
error code, the vehicle should be checked
as soon as possible in order to avoid en-
gine damage.
EBU35471Light switch “ / / ”Set the switch to “ ” to turn on the low
beam and the taillight.
Set the switch to “ ” to turn on the high
beam and the taillight.
Set the switch to “ ” to turn off the head-
lights and taillight.NOTICEECB02061Do not use the headlights with the engine
turned off for an extended period of time.
The battery may discharge to the point1. Light switch “ / / ”
L
H
1
L
HLH
UB5J7CE0.book Page 16 Thursday, November 26, 2020 1:37 PM

5-19
5
EBU31421Brake pedalPress the brake pedal to slow or stop the ve-
hicle.
EBU35642Parking brake leverSetting the parking brake lever will help keep
the vehicle from moving while parked.
To engage the parking brake, pull the lever
firmly.
To release the parking brake, pull slightly on
the lever, press the release button, and then
push the lever to its original position.TIPSpring tension helps return the lever to its
original position.
1. Brake pedal
1
1. Release button
2. Parking brake lever
12
UB5J7CE0.book Page 19 Thursday, November 26, 2020 1:37 PM

5-25
5
EBU31503Glove compartmentStore lightweight or frequently used items,
such as your driving gloves or vehicle docu-
ments, in this compartment.
NOTICEECB02071To protect from damage, do not put metal
items, like tools, or sharply edged items di-
rectly in the glove compartment. If they
must be stored, wrap them in appropriate
cushioning material. EBU38570Storage compartments
1. Unlock.
2. Open.Glove compartment load limit: 4.5 kg (9 lb)
1
2
1. Storage compartment
1
UB5J7CE0.book Page 25 Thursday, November 26, 2020 1:37 PM

5-44
5
This model has an auxiliary DC jack located at
the left side of the glove compartment. A 12-
V accessory with the proper plug, such as a
radio or smartphone charger, can be used
when the engine is running and the headlights
are off.1. Start the engine. (See page 7-2.)
2. Turn the headlights off. (See page 5-16.)
3. Open the auxiliary DC jack cap.
4. Make sure the accessory is off.
5. Insert the accessory power plug.
6. Turn the accessory on.TIP Turn off the accessory before plugging in-
to/unplugging from the jack.
 When the auxiliary DC jack is not being
used, cover it with the cap.
NOTICEECB02251Do not use accessories requiring more
than the stated maximum capacity. Do-
ing so may overload the circuit and cau-
se the fuse to blow.
 If accessories are used while the head-
lights are on and/or without the engine
running, the battery may discharge.
 Do not use an automotive cigarette light-
er or other accessories with a plug that
gets hot, because the jack can be dam-
aged.
Auxiliary DC jack maximum capacity:
10.0 A (120 W)
UB5J7CE0.book Page 44 Thursday, November 26, 2020 1:37 PM

6-2
6
Engine oil• Check oil level.
• Fill with oil to proper level if necessary.
6-6, 9-16
Drivetrain • Check front differential, transmission case, and rear final
gear for leakage. 6-6, 6-6, 6-6, 9-27,
9-30, 9-32
Coolant • Check coolant level in reservoir.
• Fill with coolant if necessary. 6-6, 9-34
Accelerator pedal • Check free play and for proper operation. 6-7
Seat belts • Check for proper operation and belt wear. 6-7
Passenger handhold • Check for stability and proper fastening. 6-7, 8-8
Steering • Check for proper operation. 6-7
Shift lever • Check for proper operation. 6-8
Fittings and fasteners • Check all fittings and fasteners. 6-8
Instruments, lights and
switches • Check for proper operation.
4-3, 5-2, 6-8, 9-65,
9-65
Wheels and tires • Check tire pressure and for wear and damage. 6-8, 9-56, 9-57
Axle boots • Check for damage. 9-36
ITEM
ROUTINE PAGE
UB5J7CE0.book Page 2 Thursday, November 26, 2020 1:37 PM