oil change YAMAHA YXZ1000R SS 2020 User Guide

9-34
9
7. Install the oil filler bolt and its gasket, andthen tighten the bolt to the specified
torque.
8. Check for oil leakage. If oil leakage is found, check for the cause.EBU36064Differential gear oilCheck the oil level and change the differential
gear oil at the intervals specified in the period-
ic maintenance chart.NOTICEECB03600When checking or changing the differen-
tial gear oil, make sure that no foreign ma-
terial enters the differential gear case. If
necessary, clean the differential gear oil
filler bolt and surrounding area.
TIPIf the recommended gear oil is not available,
SAE 80W-90 API GL-4 or GL-5 hypoid gear
oil may be used instead. Checking the differential gear oil level 1. Park the vehicle on a level surface.
2. Remove the differential gear oil filler bolt and its gasket, and then check the oil lev-
el. It should be up to the brim of the filler
hole.
Tightening torque:Final gear oil filler bolt:22 N·m (2.2 kgf·m, 16 lb·ft)
Recommended oil:SAE 80 API GL-4 Hypoid gear oil
Oil quantity: 0.18 L (0.19 US qt, 0.16 Imp.qt)
UBAS7AE0.book Page 34 Wednesday, June 19, 2019 11:51 AM

9-36
9
4. Install the differential gear oil drain boltand its new gasket, and then tighten the
bolt to the specified torque.
5. Refill the differential gear case with the recommended oil.
6. Check the oil filler bolt gasket for dam- age, and replace it if necessary.
7. Install the differential gear oil filler bolt and its gasket, and then tighten the bolt
to the specified torque.
8. Check for oil leakage. If oil leakage is found, check for the cause.
EBU35112CoolantThe coolant level should be checked regular-
ly. In addition, the coolant must be changed
at the intervals specified in the periodic main-
tenance chart.TIPIf genuine Yamaha coolant is not available,
use an ethylene glycol antifreeze containing
corrosion inhibitors for aluminum engines and
mix with distilled water at a 1:1 ratio.
Tightening torque:Differential gear oil drain bolt:9.8 N·m (0.98 kgf·m, 7.2 lb·ft)
Tightening torque: Differential gear oil filler bolt:23 N·m (2.3 kgf·m, 17 lb·ft)
Recommended coolant:YAMALUBE coolant
Coolant quantity: Coolant reservoir (up to full level):0.56 L (0.59 US qt, 0.49 Imp.qt)
Radiator (including all routes): 3.78 L (4.00 US qt, 3.33 Imp.qt)
UBAS7AE0.book Page 36 Wednesday, June 19, 2019 11:51 AM

11-2
11
SAE viscosity grades:5W-30, 10W-30, 10W-40, 15W-40, 20W-40, 20W-50
Recommended engine oil grade: API service SG type or higher, JASO standard MA
Quantity: Oil change:2.50 L (2.64 US qt, 2.20 Imp.qt)
With oil filter removal:
2.70 L (2.85 US qt, 2.38 Imp.qt)Transmission oil:Recommended brand:YAMALUBE
Type:
SAE 5W-30, 10W-30, 10W-40, 15W-40, 20W-40 or 20W-
50
Recommended transmission oil grade:
API service SE, SF, SG type or higher, JASO standard
MA Quantity:
1.50 L (1.59 US qt, 1.32 Imp.qt)
Final gear oil:Type:
SAE 80 API GL-4 Hypoid gear oil
Quantity: 0.47 L (0.50 US qt, 0.41 Imp.qt)Differential gear oil:Type:
SAE 80 API GL-4 Hypoid gear oil
Quantity: 0.18 L (0.19 US qt, 0.16 Imp.qt)Coolant quantity:Coolant reservoir (up to the maximum level mark):
0.56 L (0.59 US qt, 0.49 Imp.qt)
Radiator (including all routes): 3.78 L (4.00 US qt, 3.33 Imp.qt)Air filter:Air filter element:
Wet element
Air filter oil grade: Foam air-filter oil
Secondary air filter element: Oil-coated paper elementFuel:Recommended fuel:Regular unleaded gasoline (Gasohol [E10] acceptable)
Minimum research octane: 91
Fuel tank capacity:
34 L (9.0 US gal, 7.5 Imp.gal)
0 10 30 50 70 90 110 130 F
–20 –10 0 10 20 30 40 50 CSAE 5W-30
SAE 10W-30
SAE 10W-40
SAE 15W-40
SAE 20W-40SAE 20W-50
UBAS7AE0.book Page 2 Wednesday, June 19, 2019 11:51 AM