YAMAHA YXZ1000R SS 2020 Workshop Manual

5-19
5
This model is equipped with a self-diagnosis
device for various electrical circuits.
If a problem is detected in any of those cir-
cuits, the engine trouble warning light and/or
the YCC-S system warning light will come on
or flash, and the display will indicate an error
code.TIPYCC-S system error codes are displayed
only when the engine is stopped.
 If the display indicates an error code, note
the code number and have a Yamaha deal-
er check the vehicle. NOTICEECB00812If the multi-function display indicates an
error code, the vehicle should be checked
as soon as possible in order to avoid en-
gine damage.
EBU35471Light switch “ / / ”Set the switch to “ ” to turn on the low
beam and the taillight.
Set the switch to “ ” to turn on the high
beam and the taillight.
Set the switch to “ ” to turn off the head-
lights and taillight.NOTICEECB02061Do not use the headlights with the engine
turned off for an extended period of time.
The battery may discharge to the point1. Light switch “ / / ”
L
H
1
L
HLH
UBAS7AE0.book Page 19 Wednesday, June 19, 2019 11:51 AM

5-20
5
that the electric starter will not have
enough power to crank the engine. If this
should happen, remove the battery and re-
charge it. EBU36942Interior light switch “ ” (equipped
models)Push the upper side (a) of the interior light
switch to turn on the interior lights and push
the lower side (b) of the switch to turn off the
lights.1. Interior light (equipped models)
1
1. Interior light switch “ ”
(a)(b)
1
UBAS7AE0.book Page 20 Wednesday, June 19, 2019 11:51 AM

5-21
5
EBU31402On–Command drive knob
“2WD/4WD/DIFF LOCK”Stop the vehicle and move the On–Command
drive knob to change the drive mode to two–
wheel drive, four–wheel drive, or four–wheel
drive with differential lock. Select the appro-
priate drive according to the terrain and driv-
ing conditions.
“2WD” (two–wheel drive): Power is sup-
plied to the rear wheels only.
 “4WD” (four–wheel drive): Power is sup-
plied to the front and rear wheels. 
“DIFF LOCK” (four–wheel drive with the dif-
ferential gear locked): Power is supplied to
the front and rear wheels with the differen-
tial gear locked. Unlike standard four–wheel
drive, all wheels turn at the same speed re-
gardless of traction.
EBU31413Accelerator pedalPress the accelerator pedal to increase en-
gine speed and thus vehicle speed. Release
the accelator pedal and spring tension will re-
turn the pedal to idle position.
1. On-Command drive knob “2WD/4WD/DIFF LOCK”
1
1. Accelerator pedal
1
UBAS7AE0.book Page 21 Wednesday, June 19, 2019 11:51 AM

5-22
5
EBU31421Brake pedalPress the brake pedal to slow or stop the ve-
hicle.
EBU35642Parking brake leverSetting the parking brake lever will help keep
the vehicle from moving while parked.
To engage the parking brake, pull the lever
firmly.
To release the parking brake, pull slightly on
the lever, press the release button, and then
push the lever to its original position.TIPSpring tension helps return the lever to its
original position.
1. Brake pedal
1
1. Release button
2. Parking brake lever
12
UBAS7AE0.book Page 22 Wednesday, June 19, 2019 11:51 AM

5-23
5
If you drive the vehicle with the parking
brake engaged, a buzzer will sound. EBU36633YCC-S systemThis vehicle is equipped with the Yamaha
Chip Controlled-Shift system (YCC-S) with
AUTO DOWNSHIFT.
YCC-S allows the driver to operate the man-
ual transmission without having to operate
the clutch. AUTO DOWNSHIFT automatically
shifts the transmission into first gear when
coming to a stop under normal conditions.
The transmission is operated using the drive
select lever and the shift paddles. The drive
select lever is used to shift the transmission
into forward drive (first gear), neutral, and re-
verse gear. The shift paddles are used to shift
through the forward gears.
When the drive select lever or shift paddles
are moved, a signal is sent to the MCU (motor
control unit) which disengages the clutch, the
gear shift is made, and then the clutch is re- engaged once the engine is running at proper
speed. Clutch engagement is controlled by
the MCU according to engine speed and oth-
er driving conditions.
TIP
This is not an automatic transmission, only
the clutch system is automatic.
 The gears must be shifted by the driver, ex-
cept when AUTO DOWNSHIFT shifts the
transmission into first gear.
 See page 7-3 for more information on shift-
ing.
UBAS7AE0.book Page 23 Wednesday, June 19, 2019 11:51 AM

5-24
5
EBU36652Drive select lever and shift paddlesThe drive select lever is used to shift the
transmission into forward drive (first gear),
neutral, and reverse gear.Use the shift paddles to shift through the for-
ward gears. Pull and release the shift
paddle “ ” to shift up. Pull and release the
shift paddle “ ” to shift down.
TIPRead “Shifting and reverse driving” for shift-
ing instructions. (See page 7-3.)
1. Drive select lever
1
1. Shift paddle “ ”
2. Shift paddle “ ”
+
–
2
1
UBAS7AE0.book Page 24 Wednesday, June 19, 2019 11:51 AM

5-25
5
EBU31451Fuel tank capRemove the fuel tank cap when refueling. To
open, turn counterclockwise. When finished
refueling, install the fuel tank cap by screwing
it down clockwise.EBU37390DoorsThe door handle is located on the inside of
each door. To open a door, pull the handle. To close a
door, push or pull the door inward until it is
securely latched. Be sure the door is SE-
CURELY LATCHED AFTER CLOSING IT.
EBU33461SeatsTo remove a seat cushion, lift the front of the
cushion, and then pu
ll the cushion off.
1. Fuel tank cap
1
1. Door
2. Handle
1
2
UBAS7AE0.book Page 25 Wednesday, June 19, 2019 11:51 AM

5-26
5
To install a seat cushion, insert the projec-
tions on the rear of the seat cushion under the
seat frame, and then insert the projection on
the front of the cushion into the grommet
while pushing the cushion downward. Make
sure the seats are properly secured before
starting off. WARNING! A loose seat could
cause the operator to lose control, or cau-
se the operator or passenger to fall.
[EWB03510]
1. Driver seat cushion
1. Passenger seat cushion
1
1
UBAS7AE0.book Page 26 Wednesday, June 19, 2019 11:51 AM

5-27
5
EBU34993Adjusting the driver seat positionThe driver seat position can be adjusted to
suit the driver’s preference. WARNING! Nev-
er adjust the seat position while operating
the vehicle, otherwise the seat may sud-
denly change position, which may lead to
an accident.
[EWB03990]
To adjust the driver seat position, pull the
driver seat position adjusting lever upward
and move the seat to the desired position.
TIPAdjust the driver seat position and make sure
it is locked in place before starting off. EBU35002Adjusting the steeri ng wheel positionThe steering wheel position can be adjusted
to suit the driver’s preference. WARNING!
Never adjust the steering wheel position
while operating the vehicle, otherwise the
steering wheel may suddenly change posi-
tion, which may lead to an accident.
[EWB04000]
To adjust the steering wheel position, pull the
steering wheel position adjusting lever and
move the steering wheel to the desired posi-
tion.
1. Driver seat position adjusting lever
1
UBAS7AE0.book Page 27 Wednesday, June 19, 2019 11:51 AM

5-28
5
TIPAdjust the steering wheel position before
starting off.
EBU36184Seat beltsAlways wear the seat belts properly while rid-
ing in the vehicle. (See page 8-5.)TIPIf the vehicle is driven without the driver
seat belt fastened, a buzzer will sound.
 If the vehicle is driven without the driver
seat belt fastened, engine power will be lim-
ited.
1. Steering wheel position adjusting lever
1
1. Seat belt
1
1
UBAS7AE0.book Page 28 Wednesday, June 19, 2019 11:51 AM