charging YAMAHA YZ250F 2008 Owners Manual

2-9
MAINTENANCE SPECIFICATIONS
ELECTRICALRear wheel type
Spoke wheel----
Front rim size/material 21 × 1.60/Aluminum----
Rear rim size/material 19 × 1.85/Aluminum----
Rim runout limit: Radial ---- 2.0 mm (0.08
in)
Lateral ---- 2.0 mm (0.08
in)
Drive chain: Type/manufacturer DID520DMA2 SDH/DAIDO ----
Number of links 111 links + joint----
Chain slack 48–58 mm (1.9–2.3 in)----
Chain length (15 links) ----242.9 mm
(9.563 in)
Front disc brake: Disc outside dia.×Thickness 250 × 3.0 mm (9.84 × 0.12 in)250 × 2.5 mm
(9.84 × 0.10 in)
Pad thickness 4.4 mm (0.17 in)1.0 mm (0.04
in)
Master cylinder inside dia. 9.5 mm (0.374 in)----
Caliper cylinder inside dia. 27.0 mm (1.063 in) × 2----
Brake fluid type DOT #4----
Rear disc brake: Disc outside dia.×Thickness 245 × 4.0 mm (9.65 × 0.16 in)245 × 3.5 mm
(9.65 × 0.14 in)
Deflection limit ----0.15 mm
(0.006 in)
Pad thickness 6.4 mm (0.25 in)1.0 mm (0.04
in)
Master cylinder inside dia. 11.0 mm (0.433 in)----
Caliper cylinder inside dia. 25.4 mm (1.000 in) × 1----
Brake fluid type DOT #4----
Brake lever and brake pedal: Brake lever position 95 mm (3.74 in)----
Brake pedal height (vertical height above footrest
top) 5 mm (0.20 in)
----
Clutch lever free play (lever end) 8–13 mm (0.31–0.51 in)----
Throttle grip free play 3–5 mm (0.12–0.20 in)----
Item
StandardLimit
Item StandardLimit
Ignition system: Advancer type Electrical----
CDI: Magneto-model (stator)/manufacturer 5XC-G0/YAMAHA----
Charging coil 1 resistance (color) 720–1,080
Ωat 20 °C (68 °F) (Green–
Brown) ----
Charging coil 2 resistance (color) 44–66
Ωat 20 °C (68 °F) (Black–Pink) ----

6-2
IGNITION SYSTEM
IGNITION SYSTEM
INSPECTION STEPS
Use the following steps for checking the possibility of the malfunctioning engine being attributable to ignition system failure
and for checking the spark plug which will not spark.
*marked: Only when the ignition checker is used.
• Remove the following parts before inspection.
1. Seat
2. Fuel tank
• Use the following special tools in this inspection.
Spark gap test Spark→*Clean or replace spark plug.
No spark
↓
Check entire ignition system for connection.
(couplers, leads and ignition coil) No good→Repair or replace.
OK
↓
Check engine stop switch. No good→Replace.
OK
↓
Check ignition coil. (primary coil and secondary
coil) No good→Replace.
OK
↓
Check CDI magneto. (pickup coil and charging
coil) No good→Replace.
OK
↓
Check neutral switch. No good→Repair or replace.
OK
↓
Replace CDI unit.
Dynamic spark tester: YM-34487
Ignition checker: 90890-06754
Pocket tester:
YU-3112-C/90890-03112
6

6-3
IGNITION SYSTEM
SPARK GAP TEST
1. Disconnect the ignition coil from spark plug.
2. Remove the ignition coil cap.
3. Connect the dynamic spark tester
"1" (ignition checker "2") as
shown.
• Ignition coil "3"
• Spark plug "4"
A. For USA and CDN
B. Except for USA and CDN
4. Kick the kickstarter crank.
5. Check the ignition spark gap.
6. Start engine, and increase spark gap until misfire occurs. (for USA
and CDN only)
CHECKING THE COUPLERS,
LEADS AND IGNITION COIL
CONNECTION
1. Check: • Couplers and leads connection
Rust/dust/looseness/short-circuit
→Repair or replace.
• Ignition coil and spark plug as
they are fitted
Push in the ignition coil until it
closely contacts the spark plug
hole in the cylinder head cover.
CHECKING THE ENGINE STOP
SWITCH
1. Inspect: • Engine stop switch conduction Not conductive while it is pushed
→
Replace.
Conductive while it is freed
→Re-
place.
Set the tester selection position to
"
Ω × 1".
CHECKING THE IGNITION COIL
1. Remove the ignition coil cap.
2. Inspect:
• Primary coil resistanceOut of specification
→Replace.
3. Inspect: • Secondary coil resistanceOut of specification
→Replace. 4. Inspect:
• Sealed portion of ignition coil "a"
• Spark plug terminal pin "b"
• Threaded portion of spark plug "c"Wear
→Replace.
CHECKING THE CDI MAGNETO
1. Inspect: • Pickup coil resistanceOut of specification
→Replace.
2. Inspect: • Charging coil 1 resistanceOut of specification
→Replace.
Minimum spark gap:
6.0 mm (0.24 in)
Tester (+) lead
→Black/White
lead "1"
Tester (-) lead
→Black lead "2"
Result
Conductive (while the
engine stop switch is
pushed)
Tester (+) lead
→Orange lead "1"
Tester (-) lead
→Black lead "2"
Primary
coil resis- tance Tester se-
lector posi- tion
0.08–0.10
Ω at 20 °C
(68 °F) Ω × 1
Tester (+) lead
→Orange lead "1"
Tester (-) lead
→Spark plug termi-
nal "2"
Secondary coil resis- tance Tester se-
lector posi- tion
4.6–6.8
k
Ωat 20 °C
(68 °F) kΩ × 1
Tester (+) lead→Red lead "1"
Tester (-) lead
→White lead "2"
Pickup coil resistance Tester se-
lector posi- tion
248-372
Ω
at 20 °C (68 °F)Ω ×100
Tester (+) lead
→Brown lead "1"
Tester (-) lead
→Green lead "2"
Charging
coil 1 resis- tance Tester se-
lector posi- tion
720-1,080
Ω at 20 °C
(68 °F)Ω ×100

6-4
IGNITION SYSTEM
3. Inspect:• Charging coil 2 resistanceOut of specification
→Replace.
CHECKING THE NEUTRAL
SWITCH
1. Inspect: • Neutral switch conduction
Not conductive while it is in neutral
→
Replace.
Conductive while it is engaged
→Re-
place.
Set the tester selection position to
"
Ω × 1".
CHECKING THE CDI UNIT
Check all electrical components. If no
fault is found, replace the CDI unit.
Then check the electrical compo-
nents again. Tester (+) lead
→Pink lead "1"
Tester (-) lead
→Black lead "2"
Charging
coil 2 resis- tance Tester se-
lector posi- tion
44-66
Ω at
20 °C (68
°F)
Ω ×10
Tester (+) lead
→Sky blue lead
"1"
Tester (-) lead
→Ground "2"
Result Conductive (while gear
is in neutral)

6-5
THROTTLE POSITION SENSOR SYSTEM
THROTTLE POSITION SENSOR SYSTEM
INSPECTION STEPS
If the throttle position sensor will not operate, use the following inspection steps.
*marked: Refer to "IGNITION SYSTEM" section.
Use the following special tools in this inspection.
Check entire ignition system for connection. No good→Repair or replace.
OK
↓
Check throttle position sensor. (Throttle position
sensor coil) No good→Replace.
OK
↓
*Check CDI magneto. (Charging coil) No good→Replace.
OK
↓
Check CDI unit. (Throttle position sensor input
voltage) No good→Replace.
Pocket tester:
YU-3112-C/90890-03112