clutch YAMAHA YZ450F 2014 Owner's Manual

HANDLEBAR
4-31
EAS1SL1161
HANDLEBAR
Removing the handlber
OrderPart name Q’tyRemarks
Number plate Remove the band only.
1 Clutch cable 1 Disconnect.
2 Clutch lever holder 1
3 Engine stop switch 1
4 Brake master cylinder 1
5 Throttle cable cap 1
6 Throttle cable (pull) 1 Disconnect.
7 Throttle cable (return) 1 Disconnect.
8 Right grip 1
9 Tube guide 1
10 Collars 1
11 Left grip 1
12 Handlebar upper holder 2
13 Handlebar 1
14 Handlebar lower holder 2
15 Damper 4

HANDLEBAR
4-34
3. Tighten:
• Lower handlebar holder nut
4. Install:
• Handlebar grip “1”
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Slightly coat the handlebar left end with a
rubber adhesive.
b. Install the handlebar grip on the handlebar
by pressing the grip from the left side.
c. Wipe off any excess adhesive with a clean
cloth.
EWA13120
WARNING
Do not touch and move the handlebar grip
until its adhesive dries completely.
TIP
Install the handlebar grip to the handlebar so
that the line “a” between the two arrow marks
faces straight upward.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
5. Install:
• Engine stop switch “1”
• Clutch lever “2”
• Clutch lever holder “3”
•Clamp “4”
TIP
• The engine stop switch, the clutch lever, and
the clutch lever holder should be installed ac
-
cording to the dimensions shown.
• Pass the engine stop switch lead through the
middle of the clutch lever holder.
Lower handlebar holder nut
40 Nm (4.0 m·kgf, 29 ft·lbf)
3
4
T R..
Engine stop switch screw
0.5 Nm (0.05 m·kgf, 0.36 ft·lbf)
Clutch lever holder bolt
5 Nm (0.5 m·kgf, 3.6 ft·lbf)
T R..

HANDLEBAR
4-36
10.Install:
• Rubber cover “1”
• Cover (throttle cable housings) “2”
11.Install:
• Front brake master cylinder assembly “1”
• Front brake master cylinder holder “2”
• Bolt (brake master cylinder holder) “3”
TIP
• Install the brake master cylinder holder with
the “UP” mark facing up.
• Install in order for the top of the front brake
master cylinder assembly to be level.
• First, tighten the upper bolt, then the lower
bolt.
12.Install:
• Clutch cable “1”
TIP
Before installation, apply the lithium-soap-
based grease to the clutch cable end.
13.Adjust:
• Clutch lever free play
Refer to “ADJUSTING THE CLUTCH LE-
VER FREE PLAY” on page 3-10.
14.Adjust:
• Throttle grip free play
Refer to “ADJUSTING THE THROTTLE
GRIP FREE PLAY” on page 3-11.
Front brake master cylinder hold-
er bolt
9 Nm (0.9 m·kgf, 6.5 ft·lbf)
T R..
Clutch lever free play
7.0-12.0 mm (0.28-0.47 in)
Throttle grip free play
3.0-5.0 mm (0.12-0.20 in)
1LS

CLUTCH......................................................................................................... 5-37
REMOVING THE CLUTCH ...................................................................... 5-40
CHECKING THE FRICTION PLATES...................................................... 5-40
CHECKING THE CLUTCH PLATES ........................................................ 5-40
CHECKING THE CLUTCH SPRINGS...................................................... 5-40
CHECKING THE CLUTCH HOUSING ..................................................... 5-41
CHECKING THE CLUTCH BOSS ............................................................ 5-41
CHECKING THE PRESSURE PLATE ..................................................... 5-41
CHECKING THE PUSH LEVER SHAFT .................................................. 5-41
CHECKING THE CLUTCH PUSH RODS ................................................ 5-41
CHECKING THE PRIMARY DRIVE GEAR .............................................. 5-41
CHECKING THE PRIMARY DRIVEN GEAR ........................................... 5-42
INSTALLING THE OIL SEAL................................................................... 5-42
INSTALLING THE RIGHT CRANKCASE COVER ................................... 5-42
INSTALLING THE CLUTCH ..................................................................... 5-42
INSTALLING THE KICKSTARTER LEVER ............................................. 5-45
KICKSTATER................................................................................................. 5-46
REMOVING THE KICK SHAFT ASSEMBLY ........................................... 5-47
CHECKING THE KICK SHAFT AND RATCHET WHEEL ........................ 5-47
CHECKING THE KICK GEAR, KICK IDLE GEAR, 
AND RATCHET WHEEL ......................................................................... 5-47
INSTALLING THE KICK SHAFT ASSEMBLY .......................................... 5-47
INSTALLING THE KICK IDLE GEAR ....................................................... 5-48
SHIFT SHAFT................................................................................................. 5-49
REMOVING THE SHIFT GUIDE AND SHIFT LEVER ASSEMBLY ......... 5-51
REMOVING THE SEGMENT ................................................................... 5-51
CHECKING THE SHIFT SHAFT .............................................................. 5-51
CHECKING THE SHIFT GUIDE AND SHIFT LEVER ASSEMBLY ......... 5-51
CHECKING THE STOPPER LEVER ....................................................... 5-51
INSTALLING THE STOPPER LEVER ..................................................... 5-52
INSTALLING THE SEGMENT.................................................................. 5-52
INSTALLING THE SHIFT GUIDE AND SHIFT LEVER ASSEMBLY ....... 5-52
INSTALLING THE SHIFT SHAFT ............................................................ 5-53
INSTALLING THE SHIFT PEDAL ............................................................ 5-53
OIL PUMP AND BALANCER GEAR............................................................. 5-54
REMOVING THE BALANCER ................................................................. 5-56
CHECKING THE PRIMARY DRIVE GEAR, BALANCER SHAFT
DRIVE GEAR, AND BALANCER WEIGHT GEAR ................................. 5-56
CHECKING THE BALANCER .................................................................. 5-56
CHECKING THE OIL PUMP .................................................................... 5-56
ASSEMBLING THE OIL PUMP ................................................................ 5-57
INSTALLING THE OIL PUMP AND BALANCER GEAR .......................... 5-57

ENGINE REMOVAL
5-4
Removing the engine
OrderPart name Q’tyRemarks
Use a suitable stand to raise the front wheel
off the ground.
Seat Refer to “GENERAL CHASSIS” on page 4-1.
Side cover (left/right) Refer to “GENERAL CHASSIS” on page 4-1.
Air scoop (left / right) Refer to “GENERAL CHASSIS” on page 4-1.
Rear fender Refer to “GENERAL CHASSIS” on page 4-1
Fuel tank Refer to “FUEL TANK” on page 7-1.
Exhaust pipe and silencer Refer to “ENGINE REMOVAL” on page 5-1.
Air filter case Refer to “THROTTLE BODY” on page 7-5.
Throttle body Refer to “THROTTLE BODY” on page 7-5.
Clutch cable Refer to “CLUTCH” on page 5-37.
Shift pedal Refer to “SHIFT SHAFT” on page 5-49.
1 Engine guard 1
2 Brake pedal 1
3Spring 1
4 Cylinder head breather hose 1
5 Drive sprocket cover 1
6 Drive chain guide 1
New
New
LS
M
8
8
76
11
4 5
New
1
10
3 2

CLUTCH
5-37
EAS1SL1232
CLUTCH
Removing the clutch
OrderPart nameQ’tyRemarks
Engine oilDrain.Refer to “CHANGING THE ENGINE OIL” on page 3-15.
Brake pedalRefer to “ENGINE REMOVAL” on page 5-1.
1Clutch cable1Disconnect.
2Clutch cover1
3O-ring1
4Clutch spring6
5Pressure plate1
6Push rod 11
7Circlip1
8Washers1
9Bearing1
10Ball1
11Push rod 21
12Friction plate 15
13Clutch plate7
LS
LS
New
New
New
2
3 45
789
61011
13
12
12
18
1
14
13
13
17
16
15
T.R.
T.R.
T.R.
T.R.
LT

CLUTCH
5-38
14Friction plate 23Identification color (purple)
15Clutch boss1
16Thrust washer1
17Primary driven gear1
18Push lever shaft1
For installation, reverse the removal proce-dure.
Removing the clutch
Order Part name Q’ty Remarks
LS
LS
New
New
New
2
3 45
789
61011
13
12
12
18
1
14
13
13
17
16
15
T.R.
T.R.
T.R.
T.R.
LT

CLUTCH
5-39
Removing the right crankcase cover
OrderPart nameQ’tyRemarks
Right engine guardRefer to “ENGINE REMOVAL” on page 5-1.
Engine oilDrain.Refer to “CHANGING THE ENGINE OIL” on page 3-15.
CoolantDrain.Refer to “CHANGING THE COOLANT” on page 3-8.
Brake pedalRefer to “ENGINE REMOVAL” on page 5-1.
Clutch coverRefer to “CLUTCH” on page 5-37.
1Oil filter element cover1
2Oil filter element1
3Radiator pipe 21
4Kickstarter lever1
5Right crankcase cover1
6Gaskets1
7Dowel pin2
8Collar1
For installation, reverse the removal proce-dure.
T.R.
E
E
LS
New
New
67
2
5
4
1
7 8
New
3
LS
New
New
LS
NewNew
LT

CLUTCH
5-40
EAS1SL1233REMOVING THE CLUTCH
1. Remove:
• Clutch boss nut “1”
• Conical washer “2”
• Clutch boss “3”
TIP
While holding the clutch boss with the clutch
holder “4,” loosen the clutch boss nut.
EAS1SL1234CHECKING THE FRICTION PLATES
1. Check:
• Friction plate
Damage/wear  Replace the friction plates
as a set.
2. Measure:
• Friction plate thickness
Out of specification  Replace the friction
plates as a set.
TIP
Measure it at four points on the friction plate.
EAS1SL1235
CHECKING THE CLUTCH PLATES
1. Check:
• Clutch plate
Damage  Replace the clutch plates as a
set.
2. Measure:
• Clutch plate warpage
(with a surface plate and thickness gauge
“1”)
Out of specification  Replace the clutch
plates as a set.
EAS1SL1236CHECKING THE CLUTCH SPRINGS
1. Check:
• Clutch spring
Damage  Replace the clutch springs as a
set.
2. Measure:
• Clutch spring free length
Out of specification  Replace the clutch
springs as a set.
EAS1SL1237
Clutch holder
90890-04086
YM-91042
Friction plate thickness
2.92–3.08 mm (0.115–0.121 in)
Wear limit
2.85 mm (0.112 in)
34
12
Warpage limit
0.10 mm (0.0039 in)
Clutch spring free length
48.00 mm (1.89 in)
Limit
47.00 mm (1.85 in)

CLUTCH
5-41
CHECKING THE CLUTCH HOUSING
1. Check:
• Clutch housing dogs “a”
Damage/pitting/wear  Deburr the clutch
housing dogs or replace the clutch housing.
TIP
Pitting on the clutch housing dogs will cause er-
ratic clutch operation.
EAS1SL1238CHECKING THE CLUTCH BOSS
1. Check:
• Clutch boss splines
Damage/pitting/wear  Replace the clutch
boss.
TIP
Pitting on the clutch boss splines will cause er-
ratic clutch operation.
EAS1SL1239CHECKING THE PRESSURE PLATE
1. Check:
• Pressure plate
Crack/damage  Replace.
EAS1SL1240
CHECKING THE PUSH LEVER SHAFT
1. Check:
• Push lever shaft
Wear/damage  Replace.
EAS1SL1241CHECKING THE CLUTCH PUSH RODS
1. Check:
• Push rod 1 “1”
• Bearing “2”
• Washer “3”
• Push rod 2 “4”
•Ball “5”
Cracks/damage/wear  Replace.
2. Measure:
• Push rod 2 bending limit
Out of specification  Replace.
EAS1SL1242CHECKING THE PRIMARY DRIVE GEAR
1. Check:
• Primary drive gear
Damage/wear  Replace the primary drive
and primary driven gears as a set.
Excessive noise during operation  Re-
place the primary drive and primary driven
gears as a set.
2. Check:
• Primary-drive-gear-to-primary-driven-gear
free play
Free play exists  Replace the primary
drive and primary driven gears as a set.
EAS1SL1243
a
Push rod bending limit
0.10 mm (0.0039 in)