fuel YAMAHA YZ85 2008 User Guide
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2008, Model line: YZ85, Model: YAMAHA YZ85 2008Pages: 82, PDF Size: 3.66 MB
Page 39 of 82
OPERATION AND IMPORTANT RIDING POINTS
5-3
5
EAU41502
Engine break-in 1. Before starting the engine, fill the
fuel tank with a break-in oil-fuel
mixture as follows.
2. Start and warm up the engine.
Check the operation of the controls
and the engine stop button. (See
page 3-1.)
3. Operate the motorcycle in the low-
er gears at moderate throttle open-
ings for five to eight minutes. Stop
the engine and check the spark
plug condition (see page 6-8); it
will show a rich condition during
break-in.
4. Allow the engine to cool. Restart
the engine and operate the motor-
cycle as in the step above for five
minutes. Then, very briefly shift to
the higher gears and check the
full-throttle response. Stop the en-
gine and check the spark plug.5. After again allowing the engine to
cool, restart and run the motor-
cycle for five more minutes. Full
throttle and the higher gears may
be used, but sustained full-throttle
operation should be avoided. Stop
the engine and check the spark
plug again.
6. Allow the engine to cool, remove
the cylinder head and cylinder, and
inspect the piston and cylinder.
Remove any high spots on the pis-
ton with #600-grit wet sandpaper.
Clean all components and careful-
ly reassemble the cylinder head
and cylinder.
WARNING
EWA10320
If you are not familiar with mainte-
nance work, have a Yamaha dealerdo it for you.
7. Drain the break-in oil-fuel mixture
from the fuel tank and refill with the
specified mix. (See page 3-3.)
8. Start the engine and check the op-
eration of the motorcycle through-
out its entire operating range. Stop
the engine and check the sparkplug condition. Restart the motor-
cycle and ride it for about 10 to 15
more minutes. The motorcycle will
now be ready to ride normally.
After the engine break-in period, thor-
oughly check the motorcycle for loose
parts, oil leakage and any other prob-
lems. Be sure to inspect and make ad-
justments thoroughly, especially cable
and drive chain slack and loose
spokes. In addition, check all fittings
and fasteners for looseness, and tight-
en if necessary.
CAUTION:
ECA15560
When any of the following parts
have been replaced, they must
be broken in.
Cylinder or crankshaft:
About one hour of break-in op-
eration is necessary.
Piston, rings or transmission
gears:
These parts require about 30
minutes of break-in operation at
half-throttle or less. Observe the
condition of the engine carefully
during operation.
Recommended 2-stroke engine oil:
See page 8-1.
Mixing ratio (gasoline to oil):
15:1
U5PA86E0.book Page 3 Monday, April 9, 2007 3:16 PM
Page 40 of 82
OPERATION AND IMPORTANT RIDING POINTS
5-4
5
If any engine trouble should oc-
cur during the engine break-in
period, immediately have a
Yamaha dealer check the vehi-cle.
EAU17190
Parking When parking, stop the engine, and
then turn the fuel cock lever to “OFF”.
WARNING
EWA10310
Since the engine and exhaust
system can become very hot,
park in a place where pedestri-
ans or children are not likely to
touch them.
Do not park on a slope or on soft
ground, otherwise the vehiclemay overturn.
U5PA86E0.book Page 4 Monday, April 9, 2007 3:16 PM
Page 44 of 82
PERIODIC MAINTENANCE AND MINOR REPAIR
6-4
6
NO. ITEM ROUTINEAfter
break-inEvery
raceEvery
third raceEvery
fifth raceAs
required
√
√
√ 13*CarburetorCheck carburetor settings and for obstructions.√
Adjust and clean.√
14 Spark plugCheck condition.
Clean and regap.√
Replace.√
15 Drive chainCheck chain slack, alignment and condition.
Adjust and thoroughly lubricate chain with Yamaha
chain and cable lube or equivalent.√
√
√
√ √
Replace.√
16* *
Cooling systemCheck coolant level and for leakage.√ √
Check hoses for cracks or damage.√
Check radiator cap spring operation.√
Change coolant. Every 2 years√
17*Chassis fastenersCheck all chassis fitting and fasteners.
Correct or tighten if necessary.√
18*Air filter elementClean.
√
Replace.√
19*FrameClean and check for damage.√
20*Fuel line Clean and check for leakage.√√
U5PA86E0.book Page 4 Monday, April 9, 2007 3:16 PM
Page 70 of 82
PERIODIC MAINTENANCE AND MINOR REPAIR
6-30
63. Install the washer and axle nut,
and then lower the rear wheel so
that it is on the ground.
4. Adjust the drive chain slack. (See
page 6-21.)
5. Tighten the axle nut to the speci-
fied torque.
EAU25870
Troubleshooting Although Yamaha motorcycles receive
a thorough inspection before shipment
from the factory, trouble may occur dur-
ing operation. Any problem in the fuel,
compression, or ignition systems, for
example, can cause poor starting and
loss of power.
The following troubleshooting charts
represent quick and easy procedures
for checking these vital systems your-
self. However, should your motorcycle
require any repair, take it to a Yamaha
dealer, whose skilled technicians have
the necessary tools, experience, and
know-how to service the motorcycle
properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look like
Yamaha parts, but they are often inferi-
or, have a shorter service life and can
lead to expensive repair bills.
Tightening torque:
Axle nut:
90 Nm (9.0 m·kgf, 65 ft·lbf)
U5PA86E0.book Page 30 Monday, April 9, 2007 3:16 PM
Page 71 of 82
PERIODIC MAINTENANCE AND MINOR REPAIR
6-31
6
EAU41491
Troubleshooting charts Starting problems or poor engine performance
WARNING
EWA10840
Keep away open flames and do not smoke while checking or working on the fuel system.
Check the fuel level in
the fuel tank.1. Fuel
There is
enough fuel.
There is
no fuel.
Supply fuel.
Operate the kickstarter.2. Compression
There is compression.
There is
no compression.Check the ignition.
Have a Yamaha dealer
check the vehicle.
Remove the spark plug
and check the electrodes.3. Ignition
Wet
DryWipe off with a dry cloth and correct the
spark plug gap, or replace the spark plug.
Have a Yamaha dealer check the vehicle.The engine does not start.
Have a Yamaha dealer check the vehicle.
Open the throttle halfway and operate
the kickstarter.
Check the compression.
The engine does not start.
Check the compression.
U5PA86E0.book Page 31 Monday, April 9, 2007 3:16 PM
Page 74 of 82
MOTORCYCLE CARE AND STORAGE
7-2
7contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.
Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.
For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not leave
any marks. If the windshield isscratched, use a quality plastic
polishing compound after
washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain or near the seaSince sea salt is extremely corrosive,
carry out the following steps after each
ride in the rain or near the sea.
1. Clean the motorcycle with cold wa-
ter and a mild detergent, after the
engine has cooled down.CAUTION:
ECA10790
Do not use warm water since it in-
creases the corrosive action of thesalt.
2. Apply a corrosion protection spray
on all metal, including chrome- and
nickel-plated, surfaces to prevent
corrosion.After cleaning
1. Dry the motorcycle with a chamois
or an absorbing cloth.
2. Immediately dry the drive chain
and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally in-
duced discoloring of stainless-
steel exhaust systems can be re-
moved through polishing.)
4. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal,
including chrome- and nickel-plat-
ed, surfaces.
5. Use spray oil as a universal clean-
er to remove any remaining dirt.
6. Touch up minor paint damage
caused by stones, etc.
7. Wax all painted surfaces.
8. Let the motorcycle dry completely
before storing or covering it.
WARNING
EWA11130
Make sure that there is no oil or
wax on the brakes or tires.
U5PA86E0.book Page 2 Monday, April 9, 2007 3:16 PM
Page 75 of 82
MOTORCYCLE CARE AND STORAGE
7-3
7
If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or ac-
etone, and wash the tires with
warm water and a mild deter-
gent. Before riding at higher
speeds, test the motorcycle’s
braking performance and cor-nering behavior.
CAUTION:
ECA10800
Apply spray oil and wax spar-
ingly and make sure to wipe off
any excess.
Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.
Avoid using abrasive polishing
compounds as they will wearaway the paint.
NOTE:Consult a Yamaha dealer for advice onwhat products to use.
EAU41511
Storage Short-term
Always store your motorcycle in a cool,
dry place and, if necessary, protect it
against dust with a porous cover.CAUTION:
ECA10810
Storing the motorcycle in a
poorly ventilated room or cover-
ing it with a tarp, while it is still
wet, will allow water and humid-
ity to seep in and cause rust.
To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-cals are stored.
Long-term
Before storing your motorcycle for sev-
eral months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. For motorcycles equipped with a
fuel cock that has an “OFF” posi-
tion: Turn the fuel cock lever to
“OFF”.3. Drain the fuel tank and fuel lines,
and the carburetor float chamber
by loosening the drain bolt; this will
prevent fuel deposits from building
up.
4. Perform the following steps to pro-
tect the cylinder, piston rings, etc.
from corrosion.
a. Remove the spark plug cap
and spark plug.
b. Pour a teaspoonful of engine oil
into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap
from the spark plug, and then
install the spark plug and the
spark plug cap.
U5PA86E0.book Page 3 Monday, April 9, 2007 3:16 PM
Page 77 of 82
SPECIFICATIONS
8-1
8
Dimensions:Overall length:
YZ85 1818 mm (71.6 in)
(AUT)(BEL)(CHE)(DEU)(DNK)(ESP)(FIN)
(FRA)(GBR)(GRC)(IRL)(NLD)(NOR)(PRT)
(SWE)
YZ85 1821 mm (71.7 in) (ZAF)
YZ85LW 1903 mm (74.9 in)
YZ85LWX 1903 mm (74.9 in)
YZ85X 1818 mm (71.6 in)
Overall width:
758 mm (29.8 in)
Overall height:
YZ85 1161 mm (45.7 in)
YZ85LW 1205 mm (47.4 in)
YZ85LWX 1205 mm (47.4 in)
YZ85X 1161 mm (45.7 in)
Seat height:
YZ85 864 mm (34.0 in)
YZ85LW 904 mm (35.6 in)
YZ85LWX 904 mm (35.6 in)
YZ85X 864 mm (34.0 in)
Wheelbase:
YZ85 1255 mm (49.4 in)
(AUT)(BEL)(CHE)(DEU)(DNK)(ESP)(FIN)
(FRA)(GBR)(GRC)(IRL)(NLD)(NOR)(PRT)
(SWE)
YZ85 1258 mm (49.5 in) (ZAF)
YZ85LW 1286 mm (50.6 in)
YZ85LWX 1286 mm (50.6 in)
YZ85X 1255 mm (49.4 in)Ground clearance:
YZ85 351 mm (13.82 in)
YZ85LW 393 mm (15.47 in)
YZ85LWX 393 mm (15.47 in)
YZ85X 351 mm (13.82 in)
Weight:With oil and fuel:
YZ85 71.0 kg (157 lb)
YZ85LW 73.9 kg (163 lb)
YZ85LWX 73.9 kg (163 lb)
YZ85X 71.0 kg (157 lb)Engine:Engine type:
Liquid cooled 2-stroke
Cylinder arrangement:
Forward-inclined single cylinder
Displacement:
84.7 cm³
Bore × stroke:
47.5 × 47.8 mm (1.87 × 1.88 in)
Compression ratio:
8.20 :1
Starting system:
Kickstarter
Lubrication system:
PremixEngine oil:Type:
YAMALUBE 2-RTransmission oil:Type:
YAMALUBE 4 (10W30) or SAE 10W30
type SE motor oilOil change quantity:
0.50 L (0.53 US qt) (0.44 Imp.qt)
Cooling system:Radiator capacity (including all routes):
0.54 L (0.57 US qt) (0.48 Imp.qt)Air filter:Air filter element:
Wet elementFuel:Recommended fuel:
Premium unleaded gasoline only
Fuel tank capacity:
5.0 L (1.32 US gal) (1.10 Imp.gal)Carburetor:Manufacturer:
KEIHIN
Type × quantity:
PWK28 x 1Spark plug (s):Manufacturer/model:
NGK/BR10EG
Spark plug gap:
0.5–0.6 mm (0.020–0.024 in)Clutch:Clutch type:
Wet, multiple-discTransmission:Primary reduction system:
Spur gear
Primary reduction ratio:
65/18 (3.611)
Secondary reduction system:
Chain drive
U5PA86E0.book Page 1 Monday, April 9, 2007 3:16 PM
Page 81 of 82
INDEX
AAccessories and replacement parts ..... 6-17
Air filter element, cleaning .................... 6-12BBrake and clutch levers, checking
and lubricating .................................... 6-24
Brake and shift pedals, checking
and lubricating .................................... 6-24
Brake fluid, changing ............................ 6-21
Brake fluid level, checking .................... 6-20
Brake lever ............................................. 3-2
Brake pedal ............................................ 3-2CCables, checking and lubricating .......... 6-23
Carburetor, adjusting ............................ 6-14
Care ........................................................ 7-1
Clutch lever............................................. 3-1
Clutch lever free play, adjusting ........... 6-18
Coolant ................................................. 6-10DDrive chain, cleaning and lubricating .... 6-22
Drive chain slack .................................. 6-21EEngine break-in ...................................... 5-3
Engine idling speed .............................. 6-14
Engine, starting a warm .......................... 5-1
Engine stop button.................................. 3-1FFront and rear brake pads, checking .... 6-19
Front brake lever free play, checking ... 6-18
Front fork, adjusting ................................ 3-7
Front fork, bleeding................................. 3-8
Front fork, checking .............................. 6-25
Fuel......................................................... 3-3Fuel cock ................................................. 3-5
Fuel tank breather hose .......................... 3-5
Fuel tank cap........................................... 3-3
HHandlebar switch..................................... 3-1IIdentification numbers ............................. 9-1KKickstarter ............................................... 3-6LLabels, location of ...................................1-4MMatte color, caution .................................7-1
Model label .............................................. 9-1PParking ....................................................5-4
Part locations .......................................... 2-1
Periodic maintenance and
lubrication chart.....................................6-2
Pre-operation check list........................... 4-2RRear suspension, lubricating ................. 6-25SSafety information ...................................1-1
Seat ......................................................... 3-6
Shifting ....................................................5-2
Shift pedal ............................................... 3-1
Shock absorber assembly, adjusting ...... 3-9
Sidestand .............................................. 3-12
Spark plug, checking ...............................6-8
Specifications .......................................... 8-1
Starter (choke) knob................................ 3-6
Starting and warming up a cold
engine ................................................... 5-1Steering, checking ................................ 6-26
Storage ................................................... 7-3
Supporting the motorcycle .................... 6-27
Swingarm pivots, lubricating ................. 6-25
TThrottle cable free play, adjusting ......... 6-15
Throttle grip and cable, checking
and lubricating .................................... 6-23
Tires ...................................................... 6-15
Transmission oil ...................................... 6-9
Troubleshooting .................................... 6-30
Troubleshooting charts ......................... 6-31VVehicle identification number .................. 9-1WWheel bearings, checking..................... 6-27
Wheel (front) ......................................... 6-28
Wheel (rear) .......................................... 6-28
Wheels .................................................. 6-17
U5PA86E0.book Page 1 Monday, April 9, 2007 3:16 PM