engine oil YAMAHA YZF-R1S 2004 Owner's Manual

3-26
MEASURING THE COMPRESSION PRESSURE /
CHECKING THE ENGINE OIL LEVELCHK
ADJ
13 Nm (1.3 m
kg, 9.4 ft
lb)
NOTE: d. If the compression pressure is below the
minimum specification, pour a teaspoonful of
engine oil into the spark plug bore and mea-
sure again.
Refer to the following table.
Compression pressure
(with oil applied into the cylinder)
ReadingDiagnosis
Higher than
without oilPiston ring(s) wear
or damage

Repair.
Same as without
oilPiston, valves,
cylinder head
gasket or piston
possibly defective

Repair.
6. Install:

spark plug
7. Install:

ignition coils
EAS00069
CHECKING THE ENGINE OIL LEVEL
1. Stand the motorcycle on a level surface.

Place the motorcycle on a suitable stand.

Make sure the motorcycle is upright.
2. Start the engine, warm it up for several min-
utes, and then turn it off.
3. Check:

engine oil level
The engine oil level should be between the
minimum level mark
a and maximum level
mark
b.
Below the minimum level mark
Add the
recommended engine oil to the proper level.
ProCarManuals.com

3-27
CHECKING THE ENGINE OIL LEVEL
CHK
ADJ
NOTE:
NOTE:Recommended oil
AT 5C (40F) or higher
A
Yamalube 4 (20W40) or
SAE 20W40 type SE motor
oil
AT 1 5C (60F) or lower
B
Yamalube 4 (10W30) or
SAE 10W30 type SE motor
oil
Before checking the engine oil level, wait a few
minutes until the oil has settled.
4. Start the engine, warm it up for several min-
utes, and then turn it off.
5. Check the engine oil level again.
Before checking the engine oil level, wait a few
minutes until the oil has settled.
ProCarManuals.com

3-28
CHANGING THE ENGINE OIL
CHK
ADJ
NOTE:
CAUTION:
EAS00074
CHANGING THE ENGINE OIL
1. Start the engine, warm it up for several min-
utes, and then turn it off.
2. Place a container under the engine oil drain
bolt.
3. Remove:

bottom cowlings
Refer to “COWLINGS”.
4. Remove:

engine oil filler cap
1
Remove the engine oil filler cap 1 with the spe-
cial wrench
2 and cover 3.
5. Remove:

engine oil drain bolt
1
(along with the gasket)
6. Drain:

engine oil
(completely from the crankcase)
7. If the oil filter cartridge is also to be replaced,
perform the following procedure.
a. Remove the oil filter cartridge
1 with an oil
filter wrench
2.
Oil filter wrench
90890-01426, YU-38411
b. Lubricate the O-ring
3 of the new oil filter
cartridge with a thin coat of engine oil.
Make sure the O-ring
3 is positioned cor-
rectly in the groove of the oil filter cartridge.
c. Tighten the new oil filter cartridge to specifi-
cation with an oil filter wrench.
ProCarManuals.com

3-29
CHANGING THE ENGINE OIL /
MEASURING THE ENGINE OIL PRESSURECHK
ADJ
43 Nm (4.3 m
kg, 31 ft
lb)
CAUTION:
Oil filter cartridge
17 Nm (1.7 m
kg, 12 ft
lb)
8. Replace:

engine oil drain bolt gasket
New
9. Install:

engine oil drain bolt
(along with the new gasket)
10. Fill:

crankcase
(with the specified amount of the recom-
mended engine oil)
Quantity
Total amount
3.8 L (3.35 Imp qt, 4.02 US qt)
Without oil filter cartridge
replacement
2.9 L (2.55 Imp qt, 3.07 US qt)
With oil filter cartridge
replacement
3.1 L (2.73 Imp qt, 3.28 US qt)
11. Install:

engine oil filler cap

bottom cowlings
Refer to “COWLINGS”.
12. Start the engine, warm it up for several min-
utes, and then turn it off.
EAS00077
MEASURING THE ENGINE OIL PRESSURE
1. Check:

engine oil level
Below the minimum level mark
a
Add the
recommended engine oil to the proper level.
2. Start the engine, warm it up for several min-
utes, and then turn it off.
When the engine is cold, the engine oil will
have a higher viscosity, causing the engine
oil pressure to increase. Therefore, be sure
to measure the engine oil pressure after
warming up the engine.
3. Remove:

bottom cowlings
Refer to “COWLINGS”.
ProCarManuals.com

3-30
MEASURING THE ENGINE OIL PRESSURE
CHK
ADJ
WARNING
NOTE: 4. Remove:

oil gallery bolt
1
The engine, muffler and engine oil are ex-
tremely hot.
5. Install:

oil pressure gauge
1

adapter 2
Pressure gauge
90890-03153, YU-03153
Oil pressure adapter
90890-03139
6. Measure:

engine oil pressure
(at the following conditions)
Engine oil pressure
230 kPa
(2.3 kg / cm
2, 2.3 bar, 32.71 psi)
Engine speed
Approx. 5,000 r / min
Engine oil temperature
100C (212F)
Regarding the oil pressure as its own data may
fluctuate depending on the oil temperature and
viscosity, the oil pressure may fluctuate when
measuring. The following data should be used
only as a reference when measuring the engine
oil pressure.
ProCarManuals.com

3-31
MEASURING THE ENGINE OIL PRESSURE /
ADJUSTING THE CLUTCH CABLE FREE PLAYCHK
ADJ
8 Nm (0.8 m
kg, 5.8 ft
lb)
CAUTION:
c
b
NOTE:Engine oil pressure
Possible causes
Below
ifi i
Faulty oil pump
specificationClogged oil filter
Leaking oil
passage
Broken or
damaged oil seal
Above
specificationLeaking oil
passage
Faulty oil filter
Oil viscosity too
high
7. Install:

oil gallery bolt
1
Be carful to tighten too much.
8. Install:

bottom cowlings
Refer to “COWLINGS”.
EAS00078
ADJUSTING THE CLUTCH CABLE FREE
PLAY
1. Check:

clutch cable free play
a
Out of specification
Adjust.
Clutch cable free play (at the
end of the clutch lever)
10  15 mm (0.39  0.59 in)
2. Adjust:

clutch cable free play
Handlebar side
a. Turn the adjusting dial
1 in direction b or c
until the specified clutch cable free play is ob-
tained.
Direction
Clutch cable free play is
increased.
DirectionClutch cable free play is
decreased.
If the specified clutch cable free play cannot be
obtained on the handlebar side of the cable, use
the adjusting nut on the engine side.
ProCarManuals.com

3-50
a
b
ADJUSTING THE DRIVE CHAIN SLACK /
LUBRICATING THE DRIVE CHAINCHK
ADJ
NOTE:
DirectionDrive chain is tightened.
DirectionDrive chain is loosened.
To maintain the proper wheel alignment, adjust
both sides evenly.
d. Tighten both locknuts to specification.
Locknut
16 Nm (1.6 m
kg, 12 ft
lb)
e. Tighten the wheel axle nut to specification.
Wheel axle nut
150 Nm (15 m
kg, 108 ft
lb)
EAS00142
LUBRICATING THE DRIVE CHAIN
The drive chain consists of many interacting
parts. If the drive chain is not maintained proper-
ly, it will wear out quickly. Therefore, the drive
chain should be serviced, especially when the
motorcycle is used in dusty areas.
This motorcycle has a drive chain with small
rubber O-rings between each side plate. Steam
cleaning, high-pressure washing, certain sol-
vents, and the use of a coarse brush can dam-
age these O-rings. Therefore, use only kero-
sene to clean the drive chain. Wipe the drive
chain dry and thoroughly lubricate it with engine
oil or chain lubricant that is suitable for O-ring
chains. Do not use any other lubricants on the
drive chain since they may contain solvents that
could damage the O-rings.
Recommended lubricant
Engine oil or chain lubricant
suitable for O-ring chains
ProCarManuals.com

3-61
CHECKING AND LUBRICATING THE CABLES /
LUBRICATING THE LEVERS AND PEDALS /
LUBRICATING THE SIDESTAND / LUBRICATING THE REAR SUSPENSIONCHK
ADJ
WARNING
NOTE:
EAS00170
CHECKING AND LUBRICATING THE
CABLES
The following procedure applies to all of the in-
ner and outer cables.
Damaged outer cable may cause the cable to
corrode and interfere with its movement. Re-
place damaged outer cable and inner cables
as soon as possible.
1. Check:

outer cable
Damage
Replace.
2. Check:

cable operation
Rough movement
Lubricate.
Recommended lubricant
Engine oil or a suitable cable
lubricant
Hold the cable end upright and pour a few drops
of lubricant into the cable sheath or use a suit-
able lubricating device.
EAS00171
LUBRICATING THE LEVERS AND PEDALS
Lubricate the pivoting point and metal-to-metal
moving parts of the levers and pedals.
Recommended lubricant
Lithium-soap-based grease
EAS00172
LUBRICATING THE SIDESTAND
Lubricate the pivoting point and metal-to-metal
moving parts of the sidestand.
Recommended lubricant
Lithium-soap-based grease
EAS00174
LUBRICATING THE REAR SUSPENSION
Lubricate the pivoting point and metal-to-metal
moving parts of the rear suspension.
Recommended lubricant
Molybdenum-disulfide grease
ProCarManuals.com

4-74
SWINGARM AND DRIVE CHAINCHAS
CAUTION:
2. Check:

drive chain
Stiffness
Clean and lubricate or replace.
3. Clean:

drive chain
a. Wipe the drive chain with a clean cloth.
b. Put the drive chain in kerosene and remove
any remaining dirt.
c. Remove the drive chain from the kerosene
and completely dry it.
This motorcycle has a drive chain with small
rubber O-rings
1 between the drive chain
side plates. Never use high-pressure water
or air, steam, gasoline, certain solvents
(e.g., benzine), or a coarse brush to clean the
drive chain. High-pressure methods could
force dirt or water into the drive chain’s in-
ternals, and solvents will deteriorate the O-
rings. A coarse brush can also damage the
O-rings. Therefore, use only kerosene to
clean the drive chain. Don’t soak drive chain
in kerosine more them ten minutes. O-ring is
damage by kerosine.
4. Check:

O-rings
1
Damage
Replace the drive chain.

drive chain rollers
2
Damage / wear
Replace the drive chain.

drive chain side plates
3
Damage / wear
Replace the drive chain.
Cracks
Replace the drive chain and make
sure the battery breather hose is properly
routed away from the drive chain and below
the swingarm.
5. Lubricate:

drive chain
Recommended lubricant
Engine oil or chain lubricant
suitable for O-ring chains
ProCarManuals.com

5-5
Order Job / Part Q’ty Remarks
1
2Disconnecting the leads and hoses
Fuel tank
Air filter case
Throttle body assembly
Engine oil
Oil cooler
Air cut-off valve
Starter motor
Battery negative lead
Battery positive lead1
1Disconnect the parts in the order listed.
Refer to “FUEL TANK” in chapter 3.
Refer to “AIR FILTER CASE” in chapter 3.
Refer to “THROTTLE BODIES” in
chapter 7.
Drain.
Refer to “CHANGING THE ENGINE OIL”
in chapter 3.
Refer to “OIL COOLER” in chapter 6.
Refer to “AIR INDUCTION SYSTEM” in
chapter 7.
Refer to “STARTING SYSTEM” in
chapter 7.
ENGINEENG
LEADS AND HOSES
ProCarManuals.com