YAMAHA YZF-R1S 2004 Service Manual

5-99
Order Job / Part Q’ty Remarks
Disassembling the main axle
assembly
2nd pinion gear
Toothed lock washer
Toothed lock washer retainer
6th pinion gear
Collar
Washer
Circlip
3rd pinion gear
Circlip
Washer
5th pinion gear
Collar
Main axle1
1
1
1
1
1
1
1
1
1
1
1
1Disassemble the parts in the order listed.
1
2
3
4
5
6
7
8
9
10
11
12
13
TRANSMISSIONENG
ProCarManuals.com

5-100
Order Job / Part Q’ty Remarks
Bearing housing
Bearing1
1
For installation, reverse the removal
procedure.
14
15
TRANSMISSIONENG
ProCarManuals.com

5-101
Order Job / Part Q’ty Remarks
Disassembling the drive axle
assembly
Washer
1st wheel gear
Collar
5th wheel gear
Circlip
Washer
3rd wheel gear
Collar
Toothed lock washer
Toothed lock washer retainer
4th wheel gear
Collar
Washer
Circlip1
1
1
1
1
1
1
1
1
1
1
1
1
1Disassemble the parts in the order listed.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
TRANSMISSIONENG
ProCarManuals.com

5-102
TRANSMISSIONENG
Order Job / Part Q’ty Remarks
6th wheel gear
Circlip
Washer
Collar
2nd wheel gear
Collar
Oil seal
Bearing
Drive axle1
1
1
1
1
1
1
1
1
For installation, reverse the removal
procedure.
15
16
17
18
19
20
21
22
23
ProCarManuals.com

5-103
TRANSMISSIONENG
REMOVING THE TRANSMISSION
1. Remove:

drive axle assembly
1

shift drum retainers 2

shift fork guide bars

shift fork “L” and “R”

shift drum assembly

shift fork “C”
2. Remove:

bearing housing
1

main axle assembly 2
a. Insert two bolts 3 of the proper size, as
shown in the illustration, into the main axle
assembly bearing housing.
b. Tighten the bolts until they contact the crank-
case surface.
c. Continue tightening the bolts until the main
axle assembly comes free from the upper
crankcase.
3. Remove:

oil pipe
1

bearing 2
EAS00421
CHECKING THE SHIFT FORKS
The following procedure applies to all of the shift
forks.
1. Check:

shift fork cam follower
1

shift fork pawl 2
Bends / damage / scoring / wear
Replace
the shift fork.
ProCarManuals.com

5-104
TRANSMISSIONENG
WARNING
2. Check:

shift fork guide bar
Roll the shift fork guide bar on a flat surface.
Bends
Replace.
Do not attempt to straighten a bent shift fork
guide bar.
3. Check:

shift fork movement
(along the shift fork guide bar)
Rough movement
Replace the shift forks
and shift fork guide bar as a set.
EAS00422
CHECKING THE SHIFT DRUM ASSEMBLY
1. Check:

shift drum grooves
1
Damage / scratches / wear
Replace the
shift drum assembly.

shift drum segment
2
Damage / wear
Replace the shift drum as-
sembly.

shift drum bearing
3
Damage / pitting
Replace the shift drum
assembly.
EAS00425
CHECKING THE TRANSMISSION
1. Measure:

main axle runout
(with a centering device and dial gauge
1)
Out of specification
Replace the main
axle.
Main axle runout limit
0.08 mm (0.0032 in)
ProCarManuals.com

5-105
TRANSMISSIONENG
NOTE:
12 Nm (1.2 m
kg, 8.7 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
NOTE: 2. Measure:

drive axle runout
(with a centering device and dial gauge
1)
Out of specification
Replace the drive
axle.
Drive axle runout limit
0.08 mm (0.0032 in)
3. Check:

transmission gears
Blue discoloration / pitting / wear
Replace
the defective gear(s).

transmission gear dogs
Cracks / damage / rounded edges
Replace
the defective gear(s).
INSTALLING THE TRANSMISSION
1. Install:

bearing
1
Make the seal side of bearing face to the outside
and install it close to the right end face of the
crankcase.

oil pipe
2
2. Install:

main axle assembly
1

bearing housing 2
LOCTITE

shift fork “C”

shift drum assembly

shift fork guide bar

shift fork guide bar retainer
LOCTITE

The embossed marks on the shift forks should
face towards the right side of the engine and
be in the following sequence: “R”, “C”, “L”.

Carefully position the shift forks so that they
are installed correctly into the transmission
gears.

Install shift fork “C” into the groove in the 3rd
and 4th pinion gear on the main axle.
ProCarManuals.com

5-106
TRANSMISSIONENG
10 Nm (1.0 m
kg, 7.2 ft
lb)
NOTE:
NOTE: 3. Install:

shift fork “L”
1 and “R” 2

drive axle assembly 3

shift fork guide bar

shift fork guide bar retainer
4
LOCTITE

Install shift fork “L” into the groove in the 6th
wheel gear and shift fork “R” into the groove in
the 5th wheel gear on the drive axle.

Make sure that the drive axle bearing circlip
a
is inserted into the grooves in the upper crank-
case.
4. Check:

transmission
Rough movement
Repair.
Oil each gear, shaft, and bearing thoroughly.
ProCarManuals.com

6-1
Order Job / Part Q’ty Remarks
1
2
3
4
5Removing the radiator
Rider seat
Fuel tank
Air filter case
Side cowlings
Bottom cowling
Coolant
Fuse box stay
Coolant reservoir hose
Radiator
Radiator fan motor
Radiator inlet hose1
1
1
2
1Remove the parts in the order listed.
Refer to “AIR FILTER CASE” in chapter 3.
Drain.
Refer to “CHANGING THE COOLANT” in
chapter 3.
Disconnect.
Refer to “COWLINGS” in chapter 3.
Refer to “SEATS” in chapter 3.
10 Nm (1.0 m
kg, 7.2 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
5 Nm (0.5 m
kg, 3.6 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
RADIATORCOOL
EAS00454
COOLING SYSTEM
RADIATOR
ProCarManuals.com

6-2
6
RADIATORCOOL
Order Job / Part Q’ty Remarks
6
7
8
9
10
11Radiator inlet pipe
Oil cooler outlet hose
Water pump breather hose
Radiator outlet hose
Water pump inlet pipe
O-ring1
1
1
1
1
1
For installation, reverse the removal
procedure.
10 Nm (1.0 m
kg, 7.2 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
5 Nm (0.5 m
kg, 3.6 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
ProCarManuals.com